Vivo STAND-V002Z User manual

Dual Monitor Desk Stand
Scan the QR code with your mobile device or follow the link
for helpful videos and specifications related to this product.
Instruction Manual
https://vivo-us.com/products/stand-v002z
SKU: STAND-V002Z
[email protected]om www.vivo-us.com 309-278-5303
Chat live with an agent!
GET IN TOUCH | Monday-Friday from 7:00am-7:00pm CST

2
PACKAGE CONTENTS
A (x1)
Pole
B(x1)
Base
C(x1)
Monitor Arm
NOTE: SOME HARDWARE MAY NOT BE USED
D(x3)
M5x14
E (x2)
Wire Clip
F (x1)
Allen Wrench
Set
G (x8)
M4x12 Thumb
Bolt
J (x16)
M4 Washer
K (x4)
Cable Ring
H (x8)
M4x30
I(x8)
M4 Spacer
WARNING!
If you do not understand these directions, or if you have any doubts about the safety of the
installation, please call a qualified technician. Check carefully to make sure there are no missing or
defective parts. Improper installation may cause damage or serious injury. Do not use this product
for any purpose that is not explicitly specified in this manual. Do not exceed weight capacity.
We cannot be liable for damage or injury caused by improper mounting, incorrect assembly or
inappropriate use.
WARNING: CHOKING HAZARD
SMALL PARTS - NOT FOR CHILDREN UNDER 3 YEARS. ADULT SUPERVISION IS REQUIRED.
TIPOVER WARNING
SERIOUS OR FATAL CRUSHING INJURIES CAN OCCUR FROM TIPOVER. TO HELP PREVENT TIPOVER:
• TO PREVENT TIPPING, PLEASE BE CAREFUL NOT TO EXTEND THE ARMS TOO FAR FORWARD
OR BACKWARD.
• NEVER ALLOW CHILDREN TO CLIMB, STAND, HANG, OR PLAY ON ANY PART OF MONITOR OR
STAND.
• USE TIPOVER RESTRAINT OR ANCHOR STAND TO WALL
USE OF TIPOVER RESTRAINTS MAY ONLY REDUCE, BUT NOT ELIMINATE RISK OF TIPOVER.

3
ASSEMBLY STEPS
TOOLS NEEDED
Phillips
Screwdriver
Install the pole (A) to the base (B) using M5x14 bolts (D). Tighten with the small Allen wrench (F).
STEP 1
22lbs
(9.98kg)
DO NOT EXCEED WEIGHT CAPACITY.
Failure to do so may result in serious injury.
PER ARM
a
d
b

4
STEP 2
Slide monitor arm (C) down onto the pole and tighten the bolt with large Allen wrench (F).
c
f

5
STEP 3
OPTION A: Flat Back Monitor
Attach monitors to VESA plates on monitor arm using M4x12 thumb bolts (G) with M4 washers (J).
NOTE: Hand tighten screws to avoid stripping the plastic screw heads.
OPTION B: Curved Back Monitor
Attach monitors to the VESA plates on monitor arm using M4 spacers (I), M4x30 bolts (H) and M4
washers (J). Tighten with a Phillips screwdriver.
g
j
i
h
j

6
STEP 4
Adjust monitor height by loosening the center bolt with the large Allen wrench (F), then re-tighten
at desired height. Adjust monitor support joints using the knob on top of each bracket. If additional
tightening is needed, remove the monitor, tighten the center nut on the VESA plate with a 13mm
wrench (not included), and reinstall the monitor.
f
kno b

7
STEP 5
Attach wire clips (E) and cable rings (K) to manage wires as shown in the diagram.
e
k

LAST UPDATED: 03/05/2020
Open Monday - Friday 7:00am - 7:00pm CST,
our dedicated support team can oer immediate assistance with rapid response times. If any
parts are received damaged or defective, please contact us. We are happy to replace parts to
ensure you have a fully functioning product.
FOR MORE VIVO PRODUCTS, CHECK OUT OUR WEBSITE AT: www.vivo-us.com
[email protected] AVG. RESPONSE TIME (within oice hrs): 1HR 8M
- 23% within < 15m
- 38% within < 30m
- 61% within < 1hr
- 83% within < 2hr
- 92% within < 3hr
Love your new VIVO setup and want to share?
Tag us in your photo! @vivo_us
AVG. RESOLUTION TIME (within oice hrs): < 15 M
www.vivo-us.com
Chat live with an agent!
AVG. RESOLUTION TIME (within oice hrs): 5M 4S
309-278-5303