Vivo STAND-V001UVM User manual

Single Monitor Desk Mount
Scan the QR code with your mobile device or follow the link
for helpful videos and specifications related to this product.
Instruction Manual
https://vivo-us.com/products/stand-v001uvm
SKU: STAND-V001UVM
[email protected]om www.vivo-us.com 309-278-5303
Chat live with an agent!
GET IN TOUCH | Monday-Friday from 7:00am-7:00pm CST

2
TOOLS NEEDED
5.5 lbs
(2.5kg)
22 lbs
(10kg)
DO NOT EXCEED WEIGHT CAPACITY.
Failure to do so may result in serious injury.
WARNING!
Phillips
Screwdriver
If you do not understand these directions, or if you have any doubts about the safety of the installation, please call a
qualified technician. Check carefully to make sure there are no missing or defective parts. Improper installation may
cause damage or serious injury. Do not use this product for any purpose that is not explicitly specified in this manual. Do
not exceed weight capacity. We cannot be liable for damage or injury caused by improper mounting, incorrect assembly
or inappropriate use.
NOTE: SOME HARDWARE INCLUDED MAY NOT BE USED
TIPOVER WARNING
SERIOUS OR FATAL CRUSHING INJURIES CAN OCCUR FROM TIPOVER. TO HELP PREVENT TIPOVER:
• NEVER ALLOW CHILDREN TO CLIMB, STAND, HANG, OR PLAY ON ANY PART OF MONITOR OR STAND.
• USE TIPOVER RESTRAINT OR ANCHOR STAND TO WALL
USE OF TIPOVER RESTRAINTS MAY ONLY REDUCE, BUT NOT ELIMINATE RISK OF TIPOVER.
PACKAGE CONTENTS
A (x1)
Pole
B(x1)
Clamp
C(x1)
Swivel Arm
T-A (x1)
3mm Allen
Wrench
T-B (x1)
5mm Allen
Wrench
J(x1)
Pole Cable Clip
H(x1)
Adapter
G (x1)
So Pad
I (x2)
Cable Clip
D(x1)
VESA Plate
E(x1)
Pole Cap
S-B (x1)
M6 Security
Nut
S-C (x6)
M4x16mm
Thumbscrew
S-D (x4)
M4 Washer
S-A (x3)
M6x16mm
Screw
F (x1)
Grommet Plate
WARNING: CHOKING HAZARD
SMALL PARTS - NOT FOR CHILDREN UNDER 3 YEARS. ADULT SUPERVISION IS REQUIRED.
M-C (x4)
M6 Spacer
M-B (x4)
M4x30mm
Screw
M-A (x4)
M4x12mm
Thumbscrew
Tablet Monitor

3
ASSEMBLY STEPS
STEP 1 - Option A - Desk Clamp
Loosen the hand screw on Clamp (B) to open fully, as shown below.
Install the Clamp (B) to the Pole (A) using M6x16mm Screws (S-A) and tighten using 3mm Allen
Wrench (T-A). Mount assembly to the desktop and tighten using the hand screw.
B
T-A
A
B
S-A

4
Install Grommet Plate (F) to the Pole (A) using M6x16mm Screws (S-A) and 3mm Allen Wrench (T-A).
Attach So Pad (G) to the Grommet Plate (F). Position Pole (A) on the mounting surface and secure
using Clamp Plate (B1) and Knob (B2).
Disassemble Clamp (B) into individual parts. Remove Clamp Plate (B1) using Phillips screwdriver and
remove Knob (B2).
STEP 1 - Option B - Grommet
B
B1
B2
F
G
S-A
T-A
A
B1
B2
If desk does not have an existing
grommet hole, drill a 3/8” (10mm)
diameter hole at the desired position
through the mounting surface.

5
Attach Cable Clips (I) onto each segment of Swivel Arm (C).
STEP 3
Slide Pole Cable Clip (J) and Swivel Arm (C) onto Pole (A). Tighten Swivel Arm (C) at desired height
using 5mm Allen Wrench (T-B). Insert Pole Cap (E) into top of Pole (A).
STEP 2
C
E
T-B
A
J
I
C

6
STEP 4
With the adjustment screw holes on top, mount Adapter (H) to to VESA Plate (D) using
M4x16mm Thumbscrews (S-C) with M4 Washers (S-D) and a Phillips screwdriver. Loosly
install remaining M4x16mm Thumbscrews (S-C) into the top adjustment holes in Adapter (H).
S-C
Adjustment Holes
H
S-C
S-D
To adjust the Adapter (H) to fit the device, push device down onto springloaded tabs and position
device against the face of the adapter. With previously installed M4x16mm Thumbscrews (S-C) still
loose, center the device on the adapter, then tighten the Thumberscrews.
To remove the device for any reason, hold both sides of the device, pull down, tilt the devide, then li
it out. Reinstall the device in reverse order.
Tablet
H
S-C

7
STEP 5
STEP 6
NOTE: Before proceeding, ensure that the tilt
joint on Swivel Arm (C) is tight. Use 5mm Allen
Wrench (T-B) to secure tilt joint. C
T-B
Slide VESA Plate (D) with adapter and tablet onto the head of Swivel Arm (C). Install the M6 Security
Nut (S-B).
S-B
D

8
ADJUST AS DESIRED
Tighten the screw with the supplied 5mm Allen Wrench (T-B) to fix the tilt angle and to make any
necessary adjustments.
STEP 7
Manage cables in Cable Clips (I) and Pole Cable Clip (J).
T-B
I
J

9
To use stand as single monitor mount, follow Steps 1-3, then return to these instructions to
proceed.
OPTIONAL USE: MONITOR MOUNT
STEP 4B
Curved Back Monitor
Attach the VESA Plate (D) to the monitor with M4x30mm Screws (M-B), M6 Spacers (M-C)
and a Phillips screwdriver. NOTE: Gently tighten using a screwdriver.
Flat Back Monitor
Attach the VESA Plate (D) to the monitor with Thumbscrews (M-A) and a Phillips screwdriver.
NOTE: Hand tighten screws to avoid over tightening.
D
D

10
STEP 5B
STEP 6B
Slide VESA Plate (D) with monitor onto the head of Swivel Arm (C). Install the M6 Security Nut (S-B).
Make sure the security nut is installed before you rotate the monitor.
Manage cables in Cable Clips (I) and Pole Cable Clip (J).
S-B
I
J
D
C