Vivo STAND-V013L User manual

Black Dual Monitor + Single Laptop Desk Mount
Scan the QR code with your mobile device or follow the link
for helpful videos and specifications related to this product.
Instruction Manual
https://vivo-us.com/products/stand-v013L
SKU: STAND-V013L
[email protected]om www.vivo-us.com 309-278-5303
Chat live with an agent!
GET IN TOUCH | Monday-Friday from 7:00am-7:00pm CST

2
PACKAGE CONTENTS
WARNING!
If you do not understand these directions, or if you have any doubts about the safety of the installation,
please call a qualified technician. Check carefully to make sure there are no missing or defective parts.
Improper installation may cause damage or serious injury. Do not use this product for any purpose that is
not explicitly specified in this manual. Do not exceed weight capacity. We cannot be liable for damage or
injury caused by improper mounting, incorrect assembly or inappropriate use.
TIPOVER WARNING
SERIOUS OR FATAL CRUSHING INJURIES CAN OCCUR FROM TIPOVER. TO HELP PREVENT TIPOVER:
• NEVER ALLOW CHILDREN TO CLIMB, STAND, HANG, OR PLAY ON ANY PART OF MONITOR OR STAND.
• USE TIPOVER RESTRAINT OR ANCHOR STAND TO WALL
USE OF TIPOVER RESTRAINTS MAY ONLY REDUCE, BUT NOT ELIMINATE RISK OF TIPOVER.
WARNING: CHOKING HAZARD
SMALL PARTS - NOT FOR CHILDREN UNDER 3 YEARS. ADULT SUPERVISION IS REQUIRED.
A(x1)
Monitor Arm
C (x1)
Upper Clamp
D (x1)
Lower Clamp
E(x1)
VESA Bracket
F (x1)
Laptop Tray
G (x1)
Pole
H (x2)
Laptop Arm
I(x2)
Clip
J (x1)
Grommet
Plate
K (x6)
Arm Cable Clips
L (x1)
Pole Cable Clip
M (x1)
Support Plate
N (x5)
Pads
S-A (x2)
M6x10mm
Screw
S-B (x3)
M6x16mm
Screw
S-C (x4)
M4x8mm
Screw
M-A (x12)
M4x12mm
Screw
M-B (x12)
M5x12mm
Screw
M-C (x12)
M5 Washer
T-A (x1)
4mm Allen
Wrench
T-B (x1)
5mm Allen
Wrench
T-C (x1)
6mm Allen
Wrench
NOTE: SOME HARDWARE MAY NOT BE USED
B(x1)
Laptop Arm

3
ASSEMBLY STEPS
STEP 1
OPTION A: Clamp Installation
Install Upper Clamp (C) to Pole (G) using M6x16mm Screws (S-B) and 4mm Allen Wrench (T-A). Apply
Pads (N) to the underside of Upper Clamp (C) as shown below. Then attach Lower Clamp (D) to Upper
Clamp (C) using M6x10mm Screws (S-A) and 5mm Allen Wrench (T-B) using either the top or bottom
holes in Upper Clamp, based on desktop thickness. Secure the clamp assembly to the desktop by
tightening to the hand bolts on Lower Clamp (D).
TOOLS NEEDED
Phillips
Screwdriver
OPTION B: Existing Grommet Base Installation
The gromment installation will make use of one Hand Bolt (D1) from Lower Clamp (D). To
remove, use a Phillips screwdriver to remove the small screw from the top of Hand Bolt
(D1) and unscrew Hand Bolt (D1) from Lower Clamp (D). Apply Pads (N) to Grommet Plate
(J). Place the pole assembly over grommet hole in desk, and connect using Support Plate
(M) and previously removed Hand Bolt (D1) from underneath desk, as shown. Secure by
tightening Hand Bolt (D1).
Drill
15.4 lbs
Per Arm
(7 kg)
DO NOT EXCEED WEIGHT CAPACITY.
Failure to do so may result in serious injury.
G
N
S-B
S-A
S-A
D
D
T-A
C
T-B
T-B
D
J
N
G
M
D1
10-40mm
OR

4
STEP 2 (Option A)
SIDE LAPTOP MOUNTING:
Slide Pole Cable Clip (L) onto the Pole (G). Assemble Laptop Arm (B), Monitor Arm (A), and VESA
Bracket (E) on to Pole (G) and secure using 5mm Allen Wrench (T-B).
D
A
T-B
G
LB
E

5
CENTER LAPTOP MOUNTING:
Slide Pole Cable Clip (L) onto the Pole (G). Assemble VESA Bracket (E), Monitor Arm (A) and
Laptop Arm (A), and on to Pole (G) and secure using 5mm Allen Wrench (T-B).
STEP 3
Install Arm Cable Clips (K) to Monitor Arm (A) and Laptop Arm (B).
STEP 2 (Option B)
T-B
AE
B
L
G
K
A
B

6
STEP 5
Place Laptop Arms (H) underneath each side of Laptop Tray (F), aligning square holes in Laptop Arms
(H) with the edge and long slot on each side. Insert Clips (I) through top to secure Laptop Arms (H),
making sure all four locks on each Clip (I) are engaged with square holes in Laptop Arms (H).
S-C
S-C
STEP 4
Install two mounting screws (M-A or M-B) with Washers (M-C) onto top holes of each monitor, leaving a
3mm gap. Slide monitors onto respective Mount Arm (A) and VESA Mount (E) and insert two mounting
screws (M-A or M-B) with Washers (M-C) into remaining holes and tighten using a Phillips screwdriver.
M-A
M-B
M-A
M-B
M-C
F
H
FB
I
M-C
Insert two M4x8mm Screws (S-C) into the top holes of Laptop Tray (F), leaving a 3mm gap. Slide
Laptop Tray (F) onto Laptop Arm (B) VESA plate and tighten screws. Install final two M4x8mm Screws
(S-C) into bottom VESA holes to secure.

7
STEP 7
Route cables through Arm Cable Clips (K) and Pole Cable Clip (L). Store 5mm Allen Wrench (T-B) and
6mm Allen Wrench (T-C) in Pole Cable Clip (L) for future adjustments.
Adjust tilt on Mount Arm (A) and Laptop Arm (B) using 6mm Allen Wrench (T-C). To level height of
monitors, use 5mm Allen Wrench (T-B).
STEP 6
T-B
T-B
T-C
T-C
K
L

LAST UPDATED: 08/10/2022
REV1.2
Open Monday - Friday 7:00am - 7:00pm CST,
our dedicated support team can oer immediate assistance with rapid response times. If any
parts are received damaged or defective, please contact us. We are happy to replace parts to
ensure you have a fully functioning product.
FOR MORE VIVO PRODUCTS, CHECK OUT OUR WEBSITE AT: www.vivo-us.com
[email protected] AVG. RESPONSE TIME (within oice hrs): 1HR 8M
- 23% within < 15m
- 38% within < 30m
- 61% within < 1hr
- 83% within < 2hr
- 92% within < 3hr
Love your new VIVO setup and want to share?
Tag us in your photo! @vivo_us
AVG. RESOLUTION TIME (within oice hrs): < 15 M
www.vivo-us.com
Chat live with an agent!
AVG. RESOLUTION TIME (within oice hrs): 5M 4S
309-278-5303