Vivo STAND-V102L User manual

Pneumatic Arm Single Monitor and Laptop Desk
Scan the QR code with your mobile device or follow the link
for helpful videos and specifications related to this product.
Instruction Manual
https://vivo-us.com/products/stand-v102l
SKU: STAND-V102L
[email protected]om www.vivo-us.com 309-278-5303
Chat live with an agent!
GET IN TOUCH | Monday-Friday from 7:00am-7:00pm CST

2 3
ASSEMBLY STEPS
STEP 1
Press the cover (C) onto the clamp
brace (B1). Secure the pole (E) to
the clamp brace using three bolts
(H) and tighten with the 4mm Allen
wrench (K).
For a desk thickness of 3/8” - 1-3/4”
(10mm - 45mm), assemble the
clamp (B2) to the upper holes of
the clamp brace using clamp bolts
(B3), or for a thickness of 1-3/8” -
3-1/8” (35mm - 80mm), assemble
to the lower holes of the clamp
brace. Tighten bolts using the
6mm Allen wrench (L).
PACKAGE CONTENTS
TOOLS NEEDED
17.6lbs
(8kg)
DO NOT EXCEED WEIGHT CAPACITY.
Failure to do so may result in serious injury.
WARNING!
Phillips
Screwdriver
A (x2)
Arm
B(x1)
Clamp
C(x1)
Cover
M-A (x8)
M4x12
M-B (x8)
M4x16
M-C (x8)
M5x12
If you do not understand these directions, or if you have any doubts about the safety of the
installation, please call a qualified technician. Check carefully to make sure there are no missing or
defective parts. Improper installation may cause damage or serious injury. Do not use this product
for any purpose that is not explicitly specified in this manual. Do not exceed weight capacity.
We cannot be liable for damage or injury caused by improper mounting, incorrect assembly or
inappropriate use.
D(x2)
VESA Plate
E(x1)
Pole
F (x1)
Cable Clip
G(x2)
Thumbscrew
H (x3)
Bolt
OPTION B: Grommet Base Installation
Remove the screw, washer and clamp plate
from the clamp (B2), then remove the hand
bolt from the clamp.
Press the cover (C) onto the grommet base (J).
If necessary, drill a hole through the desktop
using a 3/8” (10mm) drill bit. Place the pole
(E) on the grommet base, making sure the
small pin inserts into the edge hole on the
bottom of the pole as shown. Position the
grommet base with pole over the grommet
hole, and secure using the hand bolt with
support plate (I) from underneath.
WARNING: CHOKING HAZARD
SMALL PARTS - NOT FOR CHILDREN UNDER 3 YEARS. ADULT SUPERVISION IS REQUIRED.
NOTE: SOME HARDWARE MAY NOT BE USED
MONITOR
9.9lbs
(4.5kg)
LAPTOP
I (x1)
Support Plate
J (x1)
Grommet Base
K (x1)
4mm Allen
Wrench
L (x1)
6mm Allen
Wrench
M (x1)
Laptop Tray
N (x2)
Laptop Arm
O (x2)
Arm Clip
P (x4)
M4x8
M-D (x8)
M5x16
M-F (x8)
Spacer
M-E (x8)
D5 Washer
Separate the clamp (B) using the 6mm
Allen wrench (L) into clamp brace (B1),
clamp (B2) and clamp bolts (B3).
STEP 2
OPTION A: Desk Clamp Installation

4 5
STEP 3
Slide the cable clip (F) and arm (A) down over the top of the pole (E). Tighten the bolt on
the arm using the 6mm Allen wrench (L).
STEP 4
Slide the second arm (A) down over the top of the pole (E). Tighten the bolt on the arm
using the 6mm Allen wrench (L).
STEP 5
Place the laptop arms (N) underneath each side of the laptop tray (M), aligning square
holes in the arms with the edge and long slot on each side. Insert the arm clips (O) through
the top to secure the arms, making sure all 4 locks on each clip are engaged with the
square holes in the arms.
STEP 6
Attach the assembled laptop holder to the 75mm and 100mm holes on the VESA
plate (D) using the M4x8 bolts (P).
STEP 7
Attach the second VESA plate (D) to the back of the monitor using bolts (M-A, M-B,
M-C, M-D) and washers (M-E). For monitors with a curved or recessed back, spacer
(M-F) may be required.
STEP 8
Slide the VESA plates (D) with monitor and laptop tray over the brackets on the
arms (A). Secure using thumb screws (G).

6 7
STEP 9
Release the locks on the underside of the laptop arms. Extend the arms, place laptop in the
holder, then adjust the arms to the width of the laptop. Engage locks to secure the laptop.
If using a thicker laptop, turn the front bumpers to the upward position for additional
support. Adjust the tilt support on each arm by turning the bolt on the side of the tilt joint
using the 6mm Allen wrench (L). Adjust the gas spring support in each arm by turning the
screw on top of the center arm joint using the 6mm Allen wrench (L). Turning clockwise
will decrease gas spring support, and counter-clockwise will increase gas spring support.
STEP 10
Remove lower covers from the arm (A) by sliding forward and o.
STEP 11
Organize cables using the clips in the upper arms. Run cables through the lower arms and
reattach the lower covers.
STEP 12
Adjust the monitor and laptop positions as desired.

LAST UPDATED: 05/11/2020
Open Monday - Friday 7:00am - 7:00pm CST,
our dedicated support team can oer immediate assistance with rapid response times. If any
parts are received damaged or defective, please contact us. We are happy to replace parts to
ensure you have a fully functioning product.
FOR MORE VIVO PRODUCTS, CHECK OUT OUR WEBSITE AT: www.vivo-us.com
[email protected] AVG. RESPONSE TIME (within oice hrs): 1HR 8M
- 23% within < 15m
- 38% within < 30m
- 61% within < 1hr
- 83% within < 2hr
- 92% within < 3hr
Love your new VIVO setup and want to share?
Tag us in your photo! @vivo_us
AVG. RESOLUTION TIME (within oice hrs): < 15 M
www.vivo-us.com
Chat live with an agent!
AVG. RESOLUTION TIME (within oice hrs): 5M 4S
309-278-5303