Vivo STAND-V001C User manual

Single Monitor Desk Mount
Scan the QR code with your mobile device or follow the link
for helpful videos and specifications related to this product.
Instruction Manual
https://vivo-us.com/products/stand-v001c
SKU: STAND-V001C
[email protected]om www.vivo-us.com 309-278-5303
Chat live with an agent!
GET IN TOUCH | Monday-Friday from 7:00am-7:00pm CST

2
PACKAGE CONTENTS
WARNING!
A (x1)
VESA Plate
B(x1)
Bracket
C(x1)
Clamp
M-A (x4)
M4x12
J (x1)
Grommet
Plate
L (x1)
4mm Allen
Key
If you do not understand these directions, or if you have any doubts about the safety of the
installation, please call a qualified technician. Check carefully to make sure there are no missing or
defective parts. Improper installation may cause damage or serious injury. Do not use this product
for any purpose that is not explicitly specified in this manual. Do not exceed weight capacity.
We cannot be liable for damage or injury caused by improper mounting, incorrect assembly or
inappropriate use.
NOTE: SOME HARDWARE INCLUDED MAY NOT BE USED
D(x1)
Pole
E(x1)
Pole Cap
F (x1)
Cable Clip
G(x1)
Grommet Base
H (x5)
Pad
I (x3)
Bolt
M-C (x4)
M5x12
M-B (x4)
M4x16
TIPOVER WARNING
SERIOUS OR FATAL CRUSHING INJURIES CAN OCCUR FROM TIPOVER. TO HELP PREVENT TIPOVER:
• NEVER ALLOW CHILDREN TO CLIMB, STAND, HANG, OR PLAY ON ANY PART OF MONITOR OR
STAND.
• USE TIPOVER RESTRAINT OR ANCHOR STAND TO WALL
USE OF TIPOVER RESTRAINTS MAY ONLY REDUCE, BUT NOT ELIMINATE RISK OF TIPOVER.
WARNING: CHOKING HAZARD
SMALL PARTS - NOT FOR CHILDREN UNDER 3 YEARS. ADULT SUPERVISION IS REQUIRED.
M-D (x4)
M5x16
M-E (x4)
D5 Washer
M-F (x4)
Spacer
M (x1)
6mm Allen
Key
K (x1)
Thumbscrew

3
ASSEMBLY STEPS
STEP 1
TOOLS NEEDED
17.6lbs
(7.98kg)
DO NOT EXCEED WEIGHT CAPACITY.
Failure to do so may result in serious injury.
Phillips
Screwdriver
Attach pole cap (E) to top of pole (D).
DE
OPTION A: Desk Clamp Installation
Assemble pole (D) to clamp base (C) with bolts (I) using 4mm Allen key (L). Attach pads (H), and
clamp to desktop.
OPTION B: Grommet Base Installation
Remove screw from clamp bolt, and remove clamp bolt from clamp (C). Attach pads (H) to grommet
base (G). Align pin on top of grommet base (G) with the small hole on the bottom of pole (D), position
over hole in desktop, and attach to desktop using clamp bolt and grommet plate (J).
STEP 2
IH
L
C
10-88mm
G
H
J
1
0
-
7
5
mm

4
STEP 3
Attach bracket (B) and cable clip (F) to pole (D). Fasten the bolt with the supplied 6mm Allen key (M).
STEP 4
OPTION A: Flat Back Monitor
For flat back monitor, attach VESA plate (A) to monitor using bolts (M-A) or (M-C) and washers (M-E).
B
F
M
M- A
M- C
M- E
A

5
STEP 4 (Continued)
OPTION B: Curved Back Monitor
For curved back monitor, attach VESA plate (A) to monitor using bolts (M-B) or (M-D), washers (M-E),
and spacers (M-F).
STEP 5
Slide the monitor onto the head of bracket (B). Attach thumb screw (K). Make sure the screw is
attached before you rotate the monitor.
A
M- B
M- D
M- E
M- F
K

6
STEP 6
If needed, adjust the bolt on the side of the hinge behind the VESA plate to tighten or loosen the tilt
angle.
STEP 7
Manage the cables using the attached cable clips.
M

7
STEP 8
Store the Allen keys in cable clip (F) for future use.
Adjust as Desired
M
L
180°
+45°
-45°
360°

LAST UPDATED: 03/05/2020
Open Monday - Friday 7:00am - 7:00pm CST,
our dedicated support team can oer immediate assistance with rapid response times. If any
parts are received damaged or defective, please contact us. We are happy to replace parts to
ensure you have a fully functioning product.
FOR MORE VIVO PRODUCTS, CHECK OUT OUR WEBSITE AT: www.vivo-us.com
[email protected] AVG. RESPONSE TIME (within oice hrs): 1HR 8M
- 23% within < 15m
- 38% within < 30m
- 61% within < 1hr
- 83% within < 2hr
- 92% within < 3hr
Love your new VIVO setup and want to share?
Tag us in your photo! @vivo_us
AVG. RESOLUTION TIME (within oice hrs): < 15 M
www.vivo-us.com
Chat live with an agent!
AVG. RESOLUTION TIME (within oice hrs): 5M 4S
309-278-5303