Vivo MOUNT-PC01 User manual

Black Under Desk and Wall PC Mount
Scan the QR code with your mobile device or follow the link
for helpful videos and specifications related to this product.
Instruction Manual
https://vivo-us.com/products/mount-pc01
SKU: MOUNT-PC01
[email protected]om www.vivo-us.com 309-278-5303

2
PACKAGE CONTENTS
TOOLS NEEDED
WARNING!
A1 (x1)
Mount
B(x4)
4.8x16
C (x4)
4.8x38
D (x4)
Anchor
E (x12)
Pad
If you do not understand these directions, or if you have any doubts about the safety of the
installation, please call a qualified technician. Check carefully to make sure there are no missing or
defective parts. Improper installation may cause damage or serious injury. Do not use this product
for any purpose that is not explicitly specified in this manual. Do not exceed weight capacity.
We cannot be liable for damage or injury caused by improper mounting, incorrect assembly or
inappropriate use.
Drill
WARNING: CHOKING HAZARD
SMALL PARTS - NOT FOR CHILDREN UNDER 3 YEARS. ADULT SUPERVISION IS REQUIRED.
CAUTION!
DO NOT INSTALL INTO DRYWALL ALONE. VERIFY YOUR WALL CONSTRUCTION. USE WOOD STUDS TO
MOUNT. We include mounting for brick and concrete If unsure, please contact us at vivo-us.com,
email at [email protected]om, or call us at 309-278-5303.
F(x4)
Washer
G (x1)
Allen Wrench
Level
22 lbs
(10 kg)
DO NOT EXCEED WEIGHT CAPACITY.
Failure to do so may result in serious injury.
Pencil
Phillips
Screwdriver

3
ASSEMBLY STEPS
STEP 1
Apply pads (E) to top, bottom, and side of the PC mount (A) as shown.
STEP 2A-1
OPTION A: Under Desk Installation
Secure PC mount (A) to bottom of desk using 4.6x16 screws (B) and washers (F).
B
F
E

4
STEP 2A-2
Loosen two screws on top of mount (one on each side) and slide side support bracket
out to maximum width.
O
STEP 2A-3
Loosen set screws for lower support using the Allen wrench (G) and slide the support
down. Place PC tower on mount, slide bottom support up until mount is fit vertically
to PC, and tighten set screws using the Allen wrench. Slide side bracket into place to
hold PC, and tighten screws using a Phillips screwdriver.
G
1
1
2
3
1
2

5
STEP 2B-1
OPTION B: Wood Wall Installation
Loosen two screws on top of mount (one on each side) and slide side support bracket out to maximum
width. Loosen set screws for lower support using the Allen wrench (G) and slide the support down.
STEP 2B-2A
3mm
X
B
B
ø3 5m
ø1 /8"
.
()
m
15mm
0.6”()
For solid wood wall, place mount (A) against wall and mark drilling locations. Using a 1/8” (3.5mm)
drill bit, drill holes 0.67” (15mm) deep. Insert two 4.8x16 screws (B) into top holes, leaving a 3mm
of thread exposed. Hang mount (A) over screws and insert two more 4.8x16 screws into lower holes.
Tighten screws with a Phillips screwdriver.
If wall has a wood stud frame, use a stud finder to locate the stud, then place mount against wall and
mark drilling locations for top and bottom holes on only one side of the mount. Using a 1/8” (3.5mm)
drill bit, drill holes 1.2” (35mm) deep. Insert a 4.8x38 screw (C) into top hole, leaving a 3mm of thread
exposed.
Hang mount (A) over screw
and insert another 4.8x38
screw into lower hole. Tighten
screws with a Phillips screw-
driver.
12

6
STEP 2B-2B
O
N
uu
√
C
D
3m m
C
OPTION C: Concrete Wall Installation
For concrete wall installation, place PC mount (A) against the wall and mark locations with a pencil.
Drill 1.2” (35mm) deep holes at marked locations using a 1/4” (6mm) drill bit. Insert anchors (D) into
holes, and insert two 4.8x38 screws (C) into top holes, leaving 3mm if thread exposed.
Hang mount over two screws in the wall. Secure with two additional 4.8x38 screws, and tighten
screws with a Phillips screwdriver.

7
STEP 2B-3
O
Place PC tower on mount, slide bottom support up until mount is fit vertically to PC, and tighten set
screws using the Allen wrench (G). Slide side bracket into place to hold PC, and tighten screws using a
Phillips screwdriver.
1
2
3

LAST UPDATED: 10/14/2019
Open Monday-Friday from 7:00am-7:00pm CST,
our dedicated support team can oer immediate assistance with rapid response times.
If any parts are received damaged or defective, please contact us.
We are happy to replace parts to ensure you have a fully functioning product.
FOR MORE VIVO PRODUCTS, CHECK OUT OUR WEBSITE AT: www.vivo-us.com
Love your new VIVO setup and want to share?
Tag us in your photo! @vivo_us
[email protected]
www.vivo-us.com
309-278-5303
AVG. RESPONSE TIME (within oice hrs): 1HR 8M
- 23% within < 15m
- 38% within < 30m
- 61% within < 1hr
- 83% within < 2hr
- 92% within < 3hr
AVG. RESOLUTION TIME (within oice hrs): 5M 4S
AVG. RESOLUTION TIME (within oice hrs): < 15 M