Vivo STAND V002A User manual

Dua Monito Wa Mount
Instruction Manual
Email: [email protected]
Live chat: www.vivo-us.com
Call: 1-800-371- 6 4
-Mode STAND V002A
Too Requied
phillips screwdriver
Package Content
1
Scan the QR code with your mobile device or follow the link
to helpful videos and specifications related to this product.
- -http vivo u.com poduct tand v002a
A (x1)
Sprin Arm
B (x2)
Extension Arm
C (x2)
Monitor Mount
D (x1)
Guide
E (x2)
Cable Clip
F (x2)
Knob
G (x2)
Cap
H (x1)
5mm Allen Wrench
I (x1)
mm Allen Wrench
-W C (x3)
Washer
-W A (x3)
Screw
- W B (x3)
Anchor
-M C (x8)
D5 Washer
-M A (x8)
M4x12
- M B (x8)
M5x12

Aemb+ Step
2
Step 1
Remove decorative covers from wall mount as shown in diagram. Remove
brace and screws on spring arm (A) using mm allen wrench (H) as shown in
diagram. Attach extension arms (B) by re-attaching brace and screws on
spring arm (A) using mm allen wrench (H).
Step 2
Option A Wood Fame Intaation
Make sure that mounting screws are anchored into the center of the studs.
The use of a stud finder is highly recommended. Use cardboard guide (D) to
mark desired position with pencil. Drill 2.2” ( mm) deep pilot hole with
3/16” (4. mm) drill bit in top center mark. Insert screw (W-A) with washer (W-
C). Leave slightly loose from wall. Hang arm (A) as shown in diagram. Make
sure wall mount is level. Insert screw (W-A) with washer (W-C). Tighten both
screws.
Step 2 (Continued)
Option B Concete Bick Wa Intaation
Use cardboard guide (D) to mark desired position with pencil. Drill 2/4”
(60mm) deep pilot holes using a 3/8” (10mm) drill bit. Insert anchors. Attach
wall mount using screws (W-A) with washers (W-C). Tighten all screws.
Slide decorative covers back onto wall mount as shown in diagram.
Step 3
Step 4
Attach monitor mounts (C) to monitors using screws (M-A or M-B) and D
washers (M-C).

Step 7
Attach cable
management clips (E)
to extension arms (B).
Step 8
Adjust arm tension by turning screw on top of center joint with 6mm
Allen Wrench (I). Clockwise reduces tension, counter-clockwise
increases tension. The tension should be just enough to hold your
monitors in place without lifting itself up. NOTE: Tighten the socket
set screw if the joint makes a popping sound.
Step 5
Slide monitors onto extension arms (B) as shown in diagram. Tighten using
mm allen wrench (H) as shown in diagram.
Step 6
Slide caps (G) onto ends of extension arms (B). Insert knobs (F) as shown in
diagram and tighten.
3

If you do not understand these directions, or if you have any
doubts about the safety of the installation, please call a
qualified technician. Check carefully to make sure there are no
missing or defective parts. Improper installation may cause
damage or serious injury. Do not use this product for any
purpose that is not explicitly specified in this manual. We
cannot be liable for damage or injury caused by incorrect
assembly or inappropriate use.
Email: [e-mail]
Live chat: www.vivo-us.com
Call: 1-800-371- 6 4
For more VIVO products, check out our
website at
www.vivo-us.com.
If any parts are received damaged or defective, please contact
us. We are happy to replace parts to ensure you have a fully
functioning product.
Safet+ Waning
Contact u at
Last updated: 0 /24/18
Step 9
Use cable management clips (E) to manage cables.
Adjut a Deied
4