Vivo MOUNT-PC03V User manual

CPU Mount
Instruction Manual
[email protected]om www.vivo-us.com 309-278-5303
Chat live with an agent!
GET IN TOUCH | Monday-Friday from 7:00am-7:00pm CST

2
ASSEMBLY STEPS
STEP 1
Remove the nuts from the CPU holder (A) and separate into wall bracket (A1), end
bracket (A2) and washers (A3).
PACKAGE CONTENTS
TOOLS NEEDED
22lbs
(10kg)
DO NOT EXCEED WEIGHT CAPACITY.
Failure to do so may result in serious injury.
WARNING!
Phillips
Screwdriver
A (x1)
CPU Holder
B(x2)
Straps
C(x2)
Knob
If you do not understand these directions, or if you have any doubts about the safety of the installation, please call a
qualified technician. Check carefully to make sure there are no missing or defective parts. Improper installation may
cause damage or serious injury. Do not use this product for any purpose that is not explicitly specified in this manual. Do
not exceed weight capacity. We cannot be liable for damage or injury caused by improper mounting, incorrect assembly
or inappropriate use.
Drill
D(x2)
ST4.2x45
E (x4)
ST4.2x32
WARNING: CHOKING HAZARD
SMALL PARTS - NOT FOR CHILDREN UNDER 3 YEARS. ADULT SUPERVISION IS REQUIRED.
CAUTION!
DO NOT INSTALL INTO DRYWALL ALONE. VERIFY YOUR WALL CONSTRUCTION. USE WOOD STUDS
IN ADDITION TO DRYWALL ANCHORS TO MOUNT. If unsure, please contact us at vivo-us.com,
email at [email protected]om, or call us at 309-278-5303.
F (x4)
Drywall
Anchor
G (x4)
Washer

3
STEP 2
Wood Stud Installation: Place the wall bracket
(A1) against the wall and mark drilling locations
with a pencil. Use of a stud finder and level is
recommended. Drill 1.8” (45mm) deep hole(s)
using a 1/8” (3mm) bit. Thread the “T” end of each
strap (B) into the slots in the wall bracket (A1), then
mount the wall bracket using ST4.2x45 screws (D)
with washers (G).
STEP 3
Reassemble the end bracket (A2) and washers
(A3) to the wall bracket (A1) using the knobs
(C), leaving slightly loose for later adjustment.
Thread the end of each strap (B) through the
slots in the end bracket, then back up into the
clip on each strap as shown.
Drywall Installation:
Place the wall bracket (A1) against the wall and
mark drilling locations with a pencil. Use of a level
is recommended. Thread the self-tapping drywall
anchors (F) directly into drilling locations. Thread
the “T” end of each strap (B) into the slots in the wall
bracket (A1), then mount the wall bracket (A1) using
ST4.2x32 screws (E) with washers (G). Please note,
at least 1 screw hole must be aligned with a wood
stud for strength.
STEP 4
Place the CPU tower into the holder (A), then adjust the end bracket to fit and tighten the knobs (C).
Tighten the straps (B), thread the ends into the buckles on the straps, and close the buckles to secure.

LAST UPDATED:09/16/2020
Open Monday - Friday 7:00am - 7:00pm CST,
our dedicated support team can oer immediate assistance with rapid response times. If any
parts are received damaged or defective, please contact us. We are happy to replace parts to
ensure you have a fully functioning product.
FOR MORE VIVO PRODUCTS, CHECK OUT OUR WEBSITE AT: www.vivo-us.com
[email protected] AVG. RESPONSE TIME (within oice hrs): 1HR 8M
- 23% within < 15m
- 38% within < 30m
- 61% within < 1hr
- 83% within < 2hr
- 92% within < 3hr
Love your new VIVO setup and want to share?
Tag us in your photo! @vivo_us
AVG. RESOLUTION TIME (within oice hrs): < 15 M
www.vivo-us.com
Chat live with an agent!
AVG. RESOLUTION TIME (within oice hrs): 5M 4S
309-278-5303