Vivo STAND-TS38B-4 User manual

Telescoping Quad Monitor Desk Mount
Scan the QR code with your mobile device or follow the link
for helpful videos and specifications related to this product.
Instruction Manual
https://vivo-us.com/products/stand-ts38b-4
SKU: STAND-TS38B-4
[email protected]om www.vivo-us.com 309-278-5303
Chat live with an agent!
GET IN TOUCH | Monday-Friday from 7:00am-7:00pm CST

2
PACKAGE CONTENTS
TOOLS NEEDED
WARNING!
Phillips
Screwdriver
A (x1)
Bottom Pole
D (x1)
Base
E (x2)
Arm with Pole
Collar
If you do not understand these directions, or if you have any doubts about the safety of the installation,
please call a qualified technician. Check carefully to make sure there are no missing or defective parts.
Improper installation may cause damage or serious injury. Do not use this product for any purpose that is
not explicitly specified in this manual. Do not exceed weight capacity. We cannot be liable for damage or
injury caused by improper mounting, incorrect assembly or inappropriate use.
F (x2)
Arm
WARNING: CHOKING HAZARD
SMALL PARTS - NOT FOR CHILDREN UNDER 3 YEARS. ADULT SUPERVISION IS REQUIRED.
I (x4)
Arm Cable Clip
17.6 lbs
(8kg)
DO NOT EXCEED WEIGHT CAPACITY.
Failure to do so may result in serious injury.
TIPOVER WARNING
SERIOUS OR FATAL CRUSHING INJURIES CAN OCCUR FROM TIPOVER. TO HELP PREVENT TIPOVER:
• TO PREVENT TIPPING, PLEASE BE CAREFUL NOT TO EXTEND THE ARMS TOO FAR FORWARD OR
BACKWARD.
• NEVER ALLOW CHILDREN TO CLIMB, STAND, HANG, OR PLAY ON ANY PART OF MONITOR OR STAND.
• USE TIPOVER RESTRAINT OR ANCHOR STAND TO WALL
USE OF TIPOVER RESTRAINTS MAY ONLY REDUCE, BUT NOT ELIMINATE RISK OF TIPOVER.
NOTE: SOME HARDWARE INCLUDED MAY NOT BE USED
G (x4)
VESA Plate
PER SCREEN
H (x2)
Pole Cable Clip
S-A (x3)
M5x16mm Screw
S-C (x4)
M6 Cap Nut
M-A (x16)
M4x12mm Thumbscrew
M-B (x16)
M4x30mm Screw
M-C (x16)
M4 Spacer
S-B (x2)
M8x42mm Screw
T-A (x1)
3mm Allen Wrench
T-B (x1)
5mm Allen Wrench
T-C (x1)
6mm Allen Wrench
B (x1)
Middle Pole
C (x1)
Top Pole With Cap

3
ASSEMBLY STEPS
STEP 1
Install Bottom Pole (A) to Base (D) using M5x16 Screws (S-A). Tighten with the 3mm Allen wrench
(T-A).
STEP 2
A
B
C
Thread Middle Pole (B) onto Bottom Pole (A), and Top Pole With Cap (C) onto Middle Pole (B).
A
D
S-A
T-A

4
STEP 3
Slide Pole Cable Clips (H) and arm assemblies onto the pole assembly. Secure arm assemblies using
6mm Allen Wrench (T-C). Attach Arm Cable Clips (I) to arms.
STEP 4
Install Arms (F) to Arms with Pole Collar (E) using M8x42mm Screws (S-B) and the 5mm Allen Wrench
(T-B). Ensure the tilt joints are facing in the same direction during installation.
H
T-C
I
F
E
S-B
T-B

5
STEP 5
OPTION A: Flat Back Monitor
Attach the VESA Plates (G) to the monitor with Thumbscrews (M-A).
NOTE: Hand tighten screws to avoid over tightening.
OPTION B: Curved Back Monitor
Attach VESA Plate (G) to the monitor with M4x30mm Screws (M-B) and M4 Spacers (M-C).
NOTE: Gently tighten using a screwdriver
G
G

6
STEP 6
STEP 7
Adjust the length of arm assemblies using 3mm Allen Wrench (T-A).
Slide VESA Plates (G) onto the arm assemblies. The monitors can be leveled using 3mm Allen Wrench
(T-A). Secure using M6 Cap Nuts (S-C).
G
T-A
S-C
T-A

7
Adjust the tilt using 5mm Allen Wrench (T-B).
STEP 8
Manage cables using Arm Cable Clips (I) and Pole Cable Clips (H).
STEP 9
I
H
T-B

LAST UPDATED: 05/02/2023
REV1.1
Open Monday - Friday 7:00am - 7:00pm CST,
our dedicated support team can oer immediate assistance with rapid response times. If any
parts are received damaged or defective, please contact us. We are happy to replace parts to
ensure you have a fully functioning product.
FOR MORE VIVO PRODUCTS, CHECK OUT OUR WEBSITE AT: www.vivo-us.com
[email protected] AVG. RESPONSE TIME (within oice hrs): 1HR 8M
- 23% within < 15m
- 38% within < 30m
- 61% within < 1hr
- 83% within < 2hr
- 92% within < 3hr
Love your new VIVO setup and want to share?
Tag us in your photo! @vivo_us
AVG. RESOLUTION TIME (within oice hrs): < 15 M
www.vivo-us.com
Chat live with an agent!
AVG. RESOLUTION TIME (within oice hrs): 5M 4S
309-278-5303