Vivo MOUNT-DLS024 User manual

VESA Adapter for Compatible Dell Monitors
Scan the QR code with your mobile device or follow the link
for helpful videos and specifications related to this product.
Instruction Manual
https://vivo-us.com/products/mount-dls024
SKU: MOUNT-DLS024
[email protected]om www.vivo-us.com 309-278-5303
Chat live with an agent!
GET IN TOUCH | Monday-Friday from 7:00am-7:00pm CST

2
ASSEMBLY STEPS
STEP 1
PACKAGE CONTENTS
TOOLS NEEDED
WARNING!
Phillips
Screwdriver
If you do not understand these directions, or if you have any doubts about the safety of the
installation, please call a qualified technician. Check carefully to make sure there are no missing or
defective parts. Improper installation may cause damage or serious injury. Do not use this product
for any purpose that is not explicitly specified in this manual. Do not exceed weight capacity.
We cannot be liable for damage or injury caused by improper mounting, incorrect assembly or
inappropriate use.
A (x1)
VESA Adapter
B(x4)
M4x10mm
Thumbscrew
C(x8)
M4x1.5mm THK
Washer
WARNING: CHOKING HAZARD
SMALL PARTS - NOT FOR CHILDREN UNDER 3 YEARS. ADULT SUPERVISION IS REQUIRED.
With the original base removed, install the VESA adapter (A) to the monitor. You will hear a
“click” when the adapter is locked in place.
D(x2)
M4x20mm
Screw
E(x2)
So Pad

3
STEP 2
NOTE: Once the thumbscrews are finger-tight,
it is recommended (but not necessary) to tighten
slightly more with a Phillips screwdriver.
IMPORTANT!
Depending on the thickness of your monitor mount’s VESA plate, it may be necessary to
remove M4 washers (C) in order for the M4x10mm thumbscrews (B) to fully engage the
threads in VESA adapter (A). Very thick VESA plates may require no washers. The best
way to determine this is to check that the M4x10mm thumbscrew (B) is protruding out the
back of VESA adapter (A), as shown in figure below. Be sure to also check that removing
M4 washers (C) does not allow the M4x10mm thumbscrew (B) to contact the back of your
monitor. If you experience diiculties, please contact customer support.
Mount the VESA adapter (A) with attached monitor to
your VESA mount using M4x10mm thumbscrews (B)
and M4 washers (C), making sure to use two washers
with each screw. Insert two M4x20mm screws (D)
partially into the unused upper holes, then places
the so pads (E) on the ends of the screws. Tighten
the screws with pads against the back of the monitor
with a Phillips screwdriver until snug.

LAST UPDATED: 06/29/2020
Open Monday - Friday 7:00am - 7:00pm CST,
our dedicated support team can oer immediate assistance with rapid response times. If any
parts are received damaged or defective, please contact us. We are happy to replace parts to
ensure you have a fully functioning product.
FOR MORE VIVO PRODUCTS, CHECK OUT OUR WEBSITE AT: www.vivo-us.com
[email protected] AVG. RESPONSE TIME (within oice hrs): 1HR 8M
- 23% within < 15m
- 38% within < 30m
- 61% within < 1hr
- 83% within < 2hr
- 92% within < 3hr
Love your new VIVO setup and want to share?
Tag us in your photo! @vivo_us
AVG. RESOLUTION TIME (within oice hrs): < 15 M
www.vivo-us.com
Chat live with an agent!
AVG. RESOLUTION TIME (within oice hrs): 5M 4S
309-278-5303