Vivo MOUNT-POLE05O User manual

Pole Mount Pneumatic Monitor Arm for VESA
75x75mm and 100x100mm
Scan the QR code with your mobile device or follow the link
for helpful videos and specifications related to this product.
Instruction Manual
https://vivo-us.com/products/mount-pole05o
SKU: MOUNT-POLE05O
[email protected]om www.vivo-us.com 309-278-5303
Chat live with an agent!
GET IN TOUCH | Monday-Friday from 7:00am-7:00pm CST

2
PACKAGE CONTENTS
WARNING!
If you do not understand these directions, or if you have any doubts about the safety of the installation,
please call a qualified technician. Check carefully to make sure there are no missing or defective parts.
Improper installation may cause damage or serious injury. Do not use this product for any purpose that is
not explicitly specified in this manual. Do not exceed weight capacity. We cannot be liable for damage or
injury caused by improper mounting, incorrect assembly or inappropriate use.
NOTE: NOT ALL HARDWARE INCLUDED WILL BE USED
A(x1)
Arm
S-A (x2)
M8x50mm Screw
T-B (x1)
5mm Allen Wrench
T-A (x1)
4mm Allen Wrench
S-B (x2)
M8x65mm Screw
B(x1)
Pole Clamp
S-C (x2)
M8 Nut
DO NOT EXCEED WEIGHT CAPACITY.
Failure to do so may result in serious injury. 4.4-17.6lbs
(2-8kg)
WARNING: CHOKING HAZARD
SMALL PARTS - NOT FOR CHILDREN UNDER 3 YEARS. ADULT SUPERVISION IS REQUIRED.
M-C (x4)
M5 Washer
M-A (x4)
M4x12mm Screw
M-B (x4)
M5x12mm Screw

3
ASSEMBLY STEPS
STEP 1
While holding Arm (A) closed, cut the shipping tie and gently release Arm (A).
A

4
STEP 2
Poles 28-45mm in Diameter: Assemble Arm (A) with Pole Clamp (B) to the pole using M8x50mm
Screws (S-A),M8 Nuts (S-C) and 5mm Allen Wrench (T-B).
Poles 46-60mm in Diameter: Assemble Arm (A) with Pole Clamp (B) to the pole using M8x65mm
Screws (S-B),M8 Nuts (S-C) and 5mm Allen Wrench (T-B).
A
B
S-A
S-C
T-B
A
B
S-C
T-B
S-B

5
STEP 3
Install Screws (M-A or M-B) and M5 Washers (M-C) to the top mounting holes of your monitor, making
sure to leave 3mm of threads exposed. Align Screws (M-A or M-B) in the VESA plate. Secure using two
more Screws (M-A or M-B) and M5 Washers (M-C) in the bottom two holes. Tighten all four screws
using the Phillips end of 4mm Allen Wrench (T-A).
T-A

6
STEP 4
Adjust gas spring support in Arm (A) using 5mm Allen Wrench (T-B). Turning counter-clockwise
increases support, and clockwise decreases.
STEP 5
Remove the cable management covers
from Arm (A) using the Phillips end of
4mm Allen Wrench (T-A). Run cables from
monitors through bottom Arm (A), then
reattach cable management covers.
A
T-B
A
T-A

7
STEP 6
Adjust the monitor tilt using 5mm Allen Wrench (T-B).
T-B

LAST UPDATED: 07/26/2022
REV1.1
Open Monday - Friday 7:00am - 7:00pm CST,
our dedicated support team can oer immediate assistance with rapid response times. If any
parts are received damaged or defective, please contact us. We are happy to replace parts to
ensure you have a fully functioning product.
FOR MORE VIVO PRODUCTS, CHECK OUT OUR WEBSITE AT: www.vivo-us.com
[email protected] AVG. RESPONSE TIME (within oice hrs): 1HR 8M
- 23% within < 15m
- 38% within < 30m
- 61% within < 1hr
- 83% within < 2hr
- 92% within < 3hr
Love your new VIVO setup and want to share?
Tag us in your photo! @vivo_us
AVG. RESOLUTION TIME (within oice hrs): < 15 M
www.vivo-us.com
Chat live with an agent!
AVG. RESOLUTION TIME (within oice hrs): 5M 4S
309-278-5303