Vivo STAND-V011 User manual

Single Monitor Extra Tall Desk Mount
Scan the QR code with your mobile device or follow the link
for helpful videos and specifications related to this product.
Instruction Manual
https://vivo-us.com/products/stand-v011
SKU: STAND-V011
[email protected]om www.vivo-us.com 309-278-5303
Chat live with an agent!
GET IN TOUCH | Monday-Friday from 7:00am-7:00pm CST

2
WARNING!
If you do not understand these directions, or if you have any doubts about the safety of the
installation, please call a qualified technician. Check carefully to make sure there are no missing or
defective parts. Improper installation may cause damage or serious injury. Do not use this product
for any purpose that is not explicitly specified in this manual. Do not exceed weight capacity.
We cannot be liable for damage or injury caused by improper mounting, incorrect assembly or
inappropriate use.
TIPOVER WARNING
SERIOUS OR FATAL CRUSHING INJURIES CAN OCCUR FROM TIPOVER. TO HELP PREVENT TIPOVER:
• NEVER ALLOW CHILDREN TO CLIMB, STAND, HANG, OR PLAY ON ANY PART OF MONITOR OR
STAND.
• USE TIPOVER RESTRAINT OR ANCHOR STAND TO WALL
USE OF TIPOVER RESTRAINTS MAY ONLY REDUCE, BUT NOT ELIMINATE RISK OF TIPOVER.
WARNING: CHOKING HAZARD
SMALL PARTS - NOT FOR CHILDREN UNDER 3 YEARS. ADULT SUPERVISION IS REQUIRED.
PACKAGE CONTENTS
A (x1)
Pole Set
B(x1)
Clamp
C(x1)
Clamp Brace
K(x1)
M10 Washer
N-1 (x3)
Wire Clip
J (x1)
Support Plate
NOTE: SOME HARDWARE INCLUDED MAY NOT BE USED
O(x1)
Allen
Wrench Set
N-2 (x2)
Wire Clip
D(x1)
Swivel Arm
E(x1)
VESA Plate
F (x3)
M5x14
G(x2)
M8x12
H (x1)
Nut
I (x1)
M10 Bolt
M (x1)
Grommet
Base Plate
L(x1)
Spring Washer
R(x4)
M4x30
S (x4)
M4 Spacer
Q (x4)
M4x12 Thumb
Bolt
P(x1)
Wrench
T-1 (x1)
So Pad
T-2 (x1)
So Pad

3
TOOLS NEEDED
22 lbs
(10 kg)
DO NOT EXCEED WEIGHT CAPACITY.
Failure to do so may result in serious injury.
Phillips
Screwdriver
ASSEMBLY STEPS
STEP 1
ASSEMBLE POLE SET
Remove the grub screws with provided
Allen wrench (O).
Connect the poles (A) by threads.
Install the previously removed grub
screws and fasten them with the Allen
wrench (O).
Option A: Desk Clamp Install
1. Install the clamp brace (C) to the pole (A) using x3 M5x14 bolts (F). See Figure 1.
2. Attach so pad (T1) to the clamp brace (C) , see Figure 2.
3. Install the clamp (B) to the pole assembly according to the thickness of the desktop. The
thickness can be changed to 3 positions. Connect using x2 M8x12 bolts (G) and tighten using the
Allen key (O). Tighten the clamp to the desktop using the plastic knob. See Figure 3.
a
c
f
Figure 1
t1
Figure 2
g
o
b
Plastic Knob Figure 3

4
STEP 1 (Continued)
Install the swivel arm (D) to the pole (A). Fasten the bolt with the supplied Allen wrench (O). Attach the
wire clip (N-1, N-2) to the pole (A) and swivel arm (D).
STEP 2
Option B: Grommet Base with Existing Hole
If existing grommet hole comes with a plastic
protector, remove it to ensure a flat surface
before installing the desk mount.
1. Install grommet base plate (M) to the pole
(A) using x3 M5x14 bolts (F). See Figure 4.
2. Attach so pad (T2) to the grommet base
plate (M) , see Figure 5.
3. Position pole (A) on the mounting surface
and secure using the support plate (J),
M10 washer (K), spring washer (L) and M10
bolt (I). Fasten M10 bolt using provided
wrench (P). See Figure 6.
a
m
f
Figure 4 t2 Figure 5
j
i
k
l
Figure 6
Option C: Grommet Base with Self-Drilled Hole
1. Position the Pole (A) on the mounting surface and mark the center hole. Drill a 3/8” (10mm)
diameter hole at the marked position through the mounting surface.
2. Install the Grommet Base Plate (M) to the Pole (A) using x3 M5x14 Bolts (F), and tighten using the
Allen Wrench (O), see Figure 4.
3. Attach So Pad (T2) to the Grommet Base Plate (M), see Figure 5.
4. Position the Pole (A) on the mounting surface and secure using Support Plate (J), M10 Washer
(K), Spring Washer (L), and M10 Bolt (I). Fasten the M10 Bolt using provided Wrench (P), see
Figure 6.
d
on1
n2

5
STEP 3
OPTION A: Flat Back Monitor
Attach the VESA plate (E) to the monitor with
M4x12 thumb bolts (Q).
NOTE: Hand tighten screws to avoid over
tightening.
q
Slide the monitor onto the head of swivel arm (D).
OPTION B: Curved Back Monitor
Attach the VESA plate (E) to the monitor with M4x30
bolts (R) and M4 spacers (S).
NOTE: Hand tighten screws to avoid over
tightening.
s
r
STEP 4
Install the security nut (H). Make sure the security
nut is installed before you rotate the monitor. For
minor height adjustment, use Allen key (O).
h

6
STEP 5
Tighten the bolt with the supplied Allen wrench (O) to fix the tilt angle.
o
To level the monitors, remove the nut (H) and turn the bolt with the Allen key (O) to raise or lower the
monitor. Replace nut (H) aer the adjustment.
o

7
STEP 6
Use the supplied Allen key set (O) to make any necessary adjustments. Manage cables and store Allen
keys (O) in wire clip (N1) for future use.

LAST UPDATED: 03/06/2020
Open Monday - Friday 7:00am - 7:00pm CST,
our dedicated support team can oer immediate assistance with rapid response times. If any
parts are received damaged or defective, please contact us. We are happy to replace parts to
ensure you have a fully functioning product.
FOR MORE VIVO PRODUCTS, CHECK OUT OUR WEBSITE AT: www.vivo-us.com
[email protected] AVG. RESPONSE TIME (within oice hrs): 1HR 8M
- 23% within < 15m
- 38% within < 30m
- 61% within < 1hr
- 83% within < 2hr
- 92% within < 3hr
Love your new VIVO setup and want to share?
Tag us in your photo! @vivo_us
AVG. RESOLUTION TIME (within oice hrs): < 15 M
www.vivo-us.com
Chat live with an agent!
AVG. RESOLUTION TIME (within oice hrs): 5M 4S
309-278-5303