Vivo STAND-V101H User manual

Pneumatic Arm Single Monitor Desk Mount
Scan the QR code with your mobile device or follow the link
for helpful videos and specifications related to this product.
Instruction Manual
https://vivo-us.com/products/stand-v101h
SKU: STAND-V101H
[email protected]om www.vivo-us.com 309-278-5303
Chat live with an agent!
GET IN TOUCH | Monday-Friday from 7:00am-7:00pm CST

2
PACKAGE CONTENTS
WARNING!
A (x1)
Monitor Arm
B(x1)
Clamp
C(x1)
Clamp Brace
O (x1)
6mm Allen
Wrench
M-A (x4)
M4x12
M-D (x4)
M5x16
N(x1)
4mm Allen
Wrench
J (x5)
Rubber Pad
K (x2)
M6x10 Bolt
L (x1)
Thumbscrew
M (x1)
3mm Allen
Wrench
If you do not understand these directions, or if you have any doubts about the safety of the
installation, please call a qualified technician. Check carefully to make sure there are no missing or
defective parts. Improper installation may cause damage or serious injury. Do not use this product
for any purpose that is not explicitly specified in this manual. Do not exceed weight capacity.
We cannot be liable for damage or injury caused by improper mounting, incorrect assembly or
inappropriate use.
NOTE: SOME HARDWARE MAY NOT BE USED
M-F (x4)
Spacer
M-E (x4)
D5 Washer
D(x1)
Grommet Base
E(x1)
Pole
F (x1)
Base Cover
G(x1)
VESA Plate
H (x1)
Support Plate
I (x1)
Cable Clip
M-C (x4)
M5x12
M-B (x4)
M4x16
WARNING: CHOKING HAZARD
SMALL PARTS - NOT FOR CHILDREN UNDER 3 YEARS. ADULT SUPERVISION IS REQUIRED.
FOR VESA ADAPTER:
A (x1)
Adapter Plate
M-A (x4)
M4x12
M-C (x8)
D5 Washer
M-B (x4)
M4 Nut

3
ASSEMBLY STEPS
TOOLS NEEDED
4-26.4lbs
(1.81-11.97kg)
DO NOT EXCEED WEIGHT CAPACITY.
Failure to do so may result in serious injury.
Phillips
Screwdriver Wrench
STEP 1
F
E
STEP 2
J
Stick rubber pads (J) to the underside of clamp
brace (C). (Skip to Step 3 Option B if grommet
base option will be used)
Slide Base cover (F) onto Pole (E).
STEP 3
OPTION A: Clamp Installation
Assemble clamp (B) to clamp brace
(C) using M6x8 bolts (K) and tighten
with 4mm Allen wrench (N). Screw
pole (E) onto clamp brace, tighten
pre-installed set screws with 3mm
Allen wrench (M), and press base
cover (F) into place. Place assemble
on edge of desk and tighten the
hand bolt to secure.
M
K
C
B
N
10-88m m

4
STEP 3 (continued)
STEP 4
OPTION B: Grommet Base Installation
Screw pole (E) onto grommet base (D), tighten pre-installed set screws with 3mm Allen wrench (M), and
press base cover (F) into place. Place assemble on edge of desk and tighten the hand bolt to secure.
Stick rubber pads (J) to the underside of grommet base.
D
J
H
M
B
10-85mm
Slide cable clip (I) and monitor arm (A) onto pole. Secure arm using 6mm Allen wrench (O).
IA
O
Remove screw from end of bolt on clamp (B) and separate parts. Use hand bolt with support plate
(H) to secure base assembly to grommet hole in desk.

5
OPTION A: Flat Back Monitor
For flat back monitor, install VESA plate
(G) to monitor using bolts (M-A) or (M-C)
and washers (M-E).
OPTION B: Curved Back Monitor
For curved back monitor, install VESA
plate (G) to monitor using bolts (M-B) or
(M-D), washers (M-E), and spacers (M-F).
STEP 5
TV
TV
TV TV
GM- E
M- A
M- C
M- E
M- B
M- D
M- F
FOR VESA ADAPTER:
M-A
A
M-B
M-C
M-C
If your monitor has a 200x100 VESA hole pattern, install “200x100 VESA adapter plate” (A) to VESA
Plate (G) using bolts (M-A), nuts (M-B), and washers (M-C).

6
STEP 6
Slide VESA plate (G) over bracket on monitor arm (A). Secure using thumb screw (L).
L
STEP 7
Remove bottom cover from monitor
arm by sliding cover forward and o.
STEP 8
Run cables through bottom of monitor arm. Reattach cover.

7
STEP 9
Adjust tension in arm and angle of monitor using 6mm Allen key (O). Clockwise reduces tension,
counterclockwise increases tension. The tension should be just enough to hold your monitor in place
without liing itself up.
STEP 10
Adjust monitor to desired position and store Allen wrenches in cable clip (I) for future use.
O
+35°
-35°
±180°
±115°
±180°
±90°
ON
M
O

LAST UPDATED: 03/06/2020
Open Monday - Friday 7:00am - 7:00pm CST,
our dedicated support team can oer immediate assistance with rapid response times. If any
parts are received damaged or defective, please contact us. We are happy to replace parts to
ensure you have a fully functioning product.
FOR MORE VIVO PRODUCTS, CHECK OUT OUR WEBSITE AT: www.vivo-us.com
[email protected] AVG. RESPONSE TIME (within oice hrs): 1HR 8M
- 23% within < 15m
- 38% within < 30m
- 61% within < 1hr
- 83% within < 2hr
- 92% within < 3hr
Love your new VIVO setup and want to share?
Tag us in your photo! @vivo_us
AVG. RESOLUTION TIME (within oice hrs): < 15 M
www.vivo-us.com
Chat live with an agent!
AVG. RESOLUTION TIME (within oice hrs): 5M 4S
309-278-5303