Vivo STAND-V102G2 User manual

Dual Monitor Desk Mount
Scan the QR code with your mobile device or follow the link
for helpful videos and specifications related to this product.
Instruction Manual
https://vivo-us.com/products/stand-v102g2
[email protected]om www.vivo-us.com 1-800-371-5654
SKU: STAND-V102G2

2
NOTE: NOT ALL HARDWARE INCLUDED WILL BE USED
PACKAGE CONTENTS
A (x1)
Base
B(x2)
Lower Arm
C(x2)
Gas Spring Arm
M (x4)
4mm Allen
Wrench
N (x1)
6mm Allen
Wrench
L(x1)
3mm Allen
Wrench
J (x1)
Clamp
K (x4)
Flat Head
Bolt
M-A (x8)
M4x12
D(x2)
VESA Plate
E(x1)
Clamp Plate
F (x1)
Grommet
Plate
G(x1)
So Pad
H (x1)
Cover
I (x1)
Clamp
Brace
M-B (x8)
M5x12
M-C (x8)
D5 Washer
WARNING!
If you do not understand these directions, or if you have any doubts about the safety of the
installation, please call a qualified technician. Check carefully to make sure there are no missing or
defective parts. Improper installation may cause damage or serious injury. Do not use this product
for any purpose that is not explicitly specified in this manual. Do not exceed weight capacity.
We cannot be liable for damage or injury caused by improper mounting, incorrect assembly or
inappropriate use.
TIPOVER WARNING
SERIOUS OR FATAL CRUSHING INJURIES CAN OCCUR FROM TIPOVER. TO HELP PREVENT TIPOVER:
• NEVER ALLOW CHILDREN TO CLIMB, STAND, HANG, OR PLAY ON ANY PART OF MONITOR OR
STAND.
• USE TIPOVER RESTRAINT OR ANCHOR STAND TO WALL
USE OF TIPOVER RESTRAINTS MAY ONLY REDUCE, BUT NOT ELIMINATE RISK OF TIPOVER.
WARNING: CHOKING HAZARD
SMALL PARTS - NOT FOR CHILDREN UNDER 3 YEARS. ADULT SUPERVISION IS REQUIRED.

3
ASSEMBLY STEPS
STEP 1
OPTION A: Clamp Installation
Attach clamp brace (I) to base (A)
using flat head bolts (K) and tighten
with 4mm Allen wrench (M). Apply
so pad (G) to underside of base.
Loosen bolts on back of clamp (J),
leaving 6mm of thread exposed.
For a desk thickness of 3/8” - 2-1/2”
(10 - 58mm), hang assembled clamp
into top 4 slots of clamp brace, or
for a desk thickness of 2” - 3-3/8”
(50 - 85mm), into lower 4 slots. Place
clamp plate (E) on top of clamp bolts.
Position base on desktop and tighten
clamp bolts evenly using 6mm Allen
wrench (N). Attach cover (H) to back
of clamp brace.
TOOLS NEEDED
Phillips
Screwdriver
33 lbs
(15 kg)
DO NOT EXCEED WEIGHT CAPACITY.
Failure to do so may result in serious injury.
PER ARM
A
I K
M
G
N
H
E
10-58mm
50-85mm
E
6mm
M
J
6mm
M
J

4
STEP 1 (Continued)
OPTION B: Grommet Base Installation
Attach grommet plate (F) to base (A) using
flat head bolts (K) and tighten with 4mm Allen
wrench (M). Apply so pad (G) to underside of
base. Position base over grommet hole in desk-
top, or drill two 3/8” (10mm) holes 1-25/32”
(45mm) apart through the desk for installation.
Remove clamp bolts from clamp (J) using
6mm Allen wrench (N) if needed. Insert clamp
bolts with clamp plate (E) up through the
underside of the desk and tighten to the base
using the 6mm Allen wrench.
STEP 2
STEP 3
Place lower arms (B) on top of base, and secure by turning the lower screws in back with 3mm Allen
wrench (N). (NOTE: The upper screws in back do not have a function on this model).
Place gas spring arms (C) on top of lower arm, and secure by turning the screw in back with 3mm
Allen wrench.
G
F
K
M
J
N
N
E
B
L
±135 °
C
L

5
STEP 4
Install the VESA plates (D) to monitors using M4x12 bolts (M-A) or M5x12 bolts (M-B) with
washers (M-C), making sure the arrow in back is pointing up.
STEP 5
Pull back the release lever on the support bracket, then place the monitor with VESA plate
into the support. Repeat for second monitor.
STEP 6
If needed, adjust gas spring arms to support the monitors using the 6mm Allen wrench. Turn the screw
in back clockwise to decrease support, and counter-clockwise to increase. Adjust the tilt joint to tighten
or loosen tilt support.
TV
TV
TV
D
M-A
M-B
M-C
2
1
N
N

6
STEP 7
Remove cable covers on upper arms using a Phillips screwdriver. Slide cable covers on
lower arms forward to remove.
STEP 8
Organize cables, then reinstall cable covers to arms.

7
STEP 9
For safety, please do not extend the monitor behind the desk. This may cause instability and tip the
desk over.
Adjust as Desired
Pleas e DO NOT rotat e monito r pas t rear edg e of desk. Or else it
will creat e an unstabl e situatio n and ma y caus e equipmen t tipove r.
±180°
±90°
+45°
-45°
PO
N
±135°
±90°

Last Updated: 03/20/2019
If any parts are received damaged or defective, please contact us. We are happy to
replace parts to ensure you have a fully functioning product.
For more VIVO products, check out our website at:
www.vivo-us.com.
Love your new VIVO setup and want to share?
Tag us in your photo! @vivo_us
[email protected]om www.vivo-us.com 1-800-371-5654