Vivo STAND-V003D User manual

Triple Vertical Monitor Desk Stand
Scan the QR code with your mobile device or follow the link
for helpful videos and specifications related to this product.
Instruction Manual
https://vivo-us.com/products/stand-v003d
SKU: STAND-V003D
[email protected]om www.vivo-us.com 309-278-5303
Chat live with an agent!
GET IN TOUCH | Monday-Friday from 7:00am-7:00pm CST

2
PACKAGE CONTENTS
WARNING!
A (x1)
Pole
B(x1)
Base
C(x3)
Arm
If you do not understand these directions, or if you have any doubts about the safety of the
installation, please call a qualified technician. Check carefully to make sure there are no missing or
defective parts. Improper installation may cause damage or serious injury. Do not use this product
for any purpose that is not explicitly specified in this manual. Do not exceed weight capacity.
We cannot be liable for damage or injury caused by improper mounting, incorrect assembly or
inappropriate use.
NOTE: SOME HARDWARE INCLUDED MAY NOT BE USED
D(x3)
VESA Plate
E(x3)
M4x6
F (x3)
M5x14
TIPOVER WARNING
SERIOUS OR FATAL CRUSHING INJURIES CAN OCCUR FROM TIPOVER. TO HELP PREVENT TIPOVER:
• NEVER ALLOW CHILDREN TO CLIMB, STAND, HANG, OR PLAY ON ANY PART OF MONITOR OR
STAND.
• USE TIPOVER RESTRAINT OR ANCHOR STAND TO WALL
USE OF TIPOVER RESTRAINTS MAY ONLY REDUCE, BUT NOT ELIMINATE RISK OF TIPOVER.
WARNING: CHOKING HAZARD
SMALL PARTS - NOT FOR CHILDREN UNDER 3 YEARS. ADULT SUPERVISION IS REQUIRED.
G (x3)
Wire Clip
H (x1)
Allen Wrench
I(x1)
Wrench
J(x12)
M4x12
Thumbscrew
K (x12)
M4x30
L(x12)
M4 Spacer

3
ASSEMBLY STEPS
STEP 1
22 lbs
Per Arm
(10 kg)
DO NOT EXCEED WEIGHT CAPACITY.
Failure to do so may result in serious injury.
TOOLS NEEDED
Phillips
Screwdriver Drill
Install the Pole (A) to the Weighted Base (B) using M5x14 Bolts (F), and tighten using
the Allen Wrench (H).
STEP 2
Remove the grub screws with provided Allen wrench (H). Connect the poles (A) by threads. Install
the previously removed grub screws and fasten them with the Allen wrench (H).
a
f
b

4
STEP 3
OPTION A: Flat Back Monitor
For monitors with flat backs attach VESA plate (D) using M4x12 Thumb Bolts (J).
STEP 4
Install Monitor Arm (C) to the Pole (A). Fasten the bolt with supplied Allen Wrench (H). Attach the Wire
Clip (G) to the Pole (A).
c
h
g
j

5
STEP 4 (Continued)
OPTION B: Curved Back Monitor
For monitors with curved or recessed backs attach VESA plate using M4x30 Bolts (K) and
M4 Spacers (L).
l
k

6
STEP 4
Slide the monitor onto the head of Monitor Arm (C) as shown in the diagram. Install the M4x6 Bolt (E).
Make sure the bolt is installed before you rotate the monitor.
e

7
STEP 5
Fasten the grub screw in Monitor Arm to fix the tilting angle by provided Allen Key (M). Manage the
wires as in the diagram.
grub
scre w

LAST UPDATED: 03/16/2020
Open Monday - Friday 7:00am - 7:00pm CST,
our dedicated support team can oer immediate assistance with rapid response times. If any
parts are received damaged or defective, please contact us. We are happy to replace parts to
ensure you have a fully functioning product.
FOR MORE VIVO PRODUCTS, CHECK OUT OUR WEBSITE AT: www.vivo-us.com
[email protected] AVG. RESPONSE TIME (within oice hrs): 1HR 8M
- 23% within < 15m
- 38% within < 30m
- 61% within < 1hr
- 83% within < 2hr
- 92% within < 3hr
Love your new VIVO setup and want to share?
Tag us in your photo! @vivo_us
AVG. RESOLUTION TIME (within oice hrs): < 15 M
www.vivo-us.com
Chat live with an agent!
AVG. RESOLUTION TIME (within oice hrs): 5M 4S
309-278-5303