Vivo STAND-V101N User manual

Single Monitor Desk Mount with Extra Long Arm
Scan the QR code with your mobile device or follow the link
for helpful videos and specications related to this product.
Instruction Manual
https://vivo-us.com/products/stand-v101n
SKU: STAND-V101N
[email protected]om www.vivo-us.com 309-278-5303
Chat live with an agent!
GET IN TOUCH | Monday-Friday from 7:00am-7:00pm CST

2
PACKAGE CONTENTS
TOOLS NEEDED
22lbs
(10kg)
DO NOT EXCEED WEIGHT CAPACITY.
Failure to do so may result in serious injury.
WARNING!
Phillips
Screwdriver
A (x1)
Arm
B (x1)
Clamp
C (x1)
Pole
M-A (x4)
M4x12mm Screw
M-B (x4)
M5x12mm Screw
M-C (x4)
M5 Washer
If you do not understand these directions, or if you have any doubts about the safety of the
installation, please call a qualied technician. Check carefully to make sure there are no missing or
defective parts. Improper installation may cause damage or serious injury. Do not use this product
for any purpose that is not explicitly specied in this manual. Do not exceed weight capacity.
We cannot be liable for damage or injury caused by improper mounting, incorrect assembly or
inappropriate use.
D (x1)
Pole Cap
E (x1)
Grommet Plate
F (x3)
Arm Cable Clip
G (x1)
Support Plate
H (x1)
Pole Cable Clip
WARNING: CHOKING HAZARD
SMALL PARTS - NOT FOR CHILDREN UNDER 3 YEARS. ADULT SUPERVISION IS REQUIRED.
NOTE: SOME HARDWARE MAY NOT BE USED
I (x5)
Rubber Pad
S-A (x3)
M6x16mm Screw
T-A (x1)
4mm Allen Wrench
T-B (x1)
5mm Allen Wrench
T-C (x1)
6mm Allen Wrench
T-D (x1)
8mm Allen Wrench
T-E (x1)
19mm Wrench

3
ASSEMBLY STEPS
STEP 2
OPTION A: Clamp Installation
Mount Pole (C) to Clamp (B) using
M6x16mm Screws (S-A). Tighten using
4mm Allen Wrench (T-A). Apply the Rubber
Pads (I) to the underside of Clamp (B), then
attach Clamp (B) to the desktop.
OPTION B: Grommet Base Installation
Separate Clamp (B) by removing the
screws in back with 4mm Allen Wrench
(T-A). Remove the screw from the top
of Clamp Bolt (B1), then remove Clamp
Bolt (B1). Apply Rubber Pads (I) to the
bottom of Grommet Base (E). Place
Support Plate (G) onto Clamp Bolt (B1),
then insert Clamp Bolt (B1) through the
grommet hole and thread into Pole (C)
as shown in the diagram.
STEP 1
Insert Pole Cap (D) into the top of Pole (C).
C
B
S-A
T-A
I
B
T-A
I
E
G
B1
C

4
STEP 3
Slide Pole Cable Clip (H) and Arm (A) onto Pole (C). Secure Arm (A) to Pole (C) using
5mm Allen Wrench (T-B).
STEP 4
Attach Arm Cable Clips (F) to Arm (A) as shown.
H
A
C
T-B
A

5
STEP 5
Insert two screws (M-A or M-B) and M5 Washers (M-C) into the top mounting holes of the
monitor, making sure to leave 3mm of thread exposed. Align screws in monitor over the
slots in the VESA plate. Secure using two more Screws (M-A or M-B) and M5 Washers (M-C)
in the bottom two holes of the monitor. Tighten all four screws using a Phillips screwdriver.

6
STEP 6
Adjust the tilt joint using 6mm Allen Wrench (T-C).
STEP 7
Store 5mm Allen Wrench (T-B) and 6mm Allen Wrench (T-C) in Pole Cable Clip (H) for
future adjustments.
T-C
T-C
T-B
H

7
STEP 9
Route cables through Arm Cable Clips (F) and Pole Cable Clips (H).
STEP 8
Tighten the joints in Arm (A) using 8mm Allen Wrench (T-D) with 19mm Wrench (T-E) and
6mm Allen Wrench (T-C).
A
T-D
T-F
T-C
F
H
T-E

LAST UPDATED: 06/01/2022
REV3
Open Monday - Friday 7:00am - 7:00pm CST,
our dedicated support team can oer immediate assistance with rapid response times. If any
parts are received damaged or defective, please contact us. We are happy to replace parts to
ensure you have a fully functioning product.
FOR MORE VIVO PRODUCTS, CHECK OUT OUR WEBSITE AT: www.vivo-us.com
Love your new VIVO setup and want to share?
Tag us in your photo! @vivo_us
[email protected] AVG. RESPONSE TIME (within oice hrs): 1HR 8M
- 23% within < 15m
- 38% within < 30m
- 61% within < 1hr
- 83% within < 2hr
- 92% within < 3hr
AVG. RESOLUTION TIME (within oice hrs): < 15 M
www.vivo-us.com
Chat live with an agent!
AVG. RESOLUTION TIME (within oice hrs): 5M 4S
309-278-5303