Vivo STAND-MIC01 User manual

Pneumatic Arm Microphone Desk Mount
Scan the QR code with your mobile device or follow the link
for helpful videos and specifications related to this product.
Instruction Manual
https://vivo-us.com/products/stand-mic01
SKU: STAND-MIC01
[email protected]om www.vivo-us.com 309-278-5303
Chat live with an agent!
GET IN TOUCH | Monday-Friday from 7:00am-7:00pm CST

2
PACKAGE CONTENTS
WARNING!
A (x1)
Arm
B(x1)
Clamp
C(x1)
Decorative
Cover
If you do not understand these directions, or if you have any doubts about the safety of the
installation, please call a qualified technician. Check carefully to make sure there are no missing or
defective parts. Improper installation may cause damage or serious injury. Do not use this product
for any purpose that is not explicitly specified in this manual. Do not exceed weight capacity.
We cannot be liable for damage or injury caused by improper mounting, incorrect assembly or
inappropriate use.
NOTE: SOME HARDWARE INCLUDED MAY NOT BE USED
D(x1)
Mic Clamp
E(x1)
Pole
F (x1)
Cable Clip
G (x3)
Bolt
H (x1)
Grommet Plate
TIPOVER WARNING
SERIOUS OR FATAL CRUSHING INJURIES CAN OCCUR FROM TIPOVER. TO HELP PREVENT TIPOVER:
• NEVER ALLOW CHILDREN TO CLIMB, STAND, HANG, OR PLAY ON ANY PART OF MONITOR OR
STAND.
• USE TIPOVER RESTRAINT OR ANCHOR STAND TO WALL
USE OF TIPOVER RESTRAINTS MAY ONLY REDUCE, BUT NOT ELIMINATE RISK OF TIPOVER.
WARNING: CHOKING HAZARD
SMALL PARTS - NOT FOR CHILDREN UNDER 3 YEARS. ADULT SUPERVISION IS REQUIRED.
I(x1)
Grommet Base
J(x1)
3mm Allen
Wrench
K (x1)
4mm Allen
Wrench
L (x1)
6mm Allen
Wrench

3
ASSEMBLY STEPS
STEP 1
TOOLS NEEDED
5.95lbs
(2.70kg)
DO NOT EXCEED WEIGHT CAPACITY.
Failure to do so may result in serious injury.
Phillips
Screwdriver
OPTION A: Clamp Installation
As delivered, the clamp (B) will fit a desktop thickness of 35-80mm. To fit a desk thickness of 10-45mm,
remove the two bolts using the 6mm Allen wrench (L), then reassemble at alternate height. Attach
decorative cover (C) to clamp (B). Attach pole (E) to clamp (B) with bolts (G) using 4mm allen wrench
(K).
35-80mm
L
10-45mm
L
C
B
E
K
G

4
STEP 1 (Continued)
STEP 2
Slide on cable management clip (F). Slide arm (A) onto pole (E) and tighten at desired height using
6mm allen wrench (L).
OPTION B: Grommet Base Installation
Disassemble clamp (B) using 6mm Allen wrench (L). Remove the screw, washer and clamp plate from
the clamp, then remove the hand bolt. If desk does not have an existing grommet hole, drill a 3/8”
(10mm) hole through the desktop. Place grommet plate (H) onto the hand bolt, then secure the pole
(E) and grommet base (I) to the desktop using the hand bolt and grommet plate. Slide on decorative
cover (C).
L
H
I
0-40mm
L
A
F
NOTE: Pin in grommet base (I)
inserts into small hole underneath
pole (E).

5
STEP 3
Screw mic clamp (D) onto arm (A) and adjust using 3mm Allen wrench (J).
STEP 4
Place mic into mic clamp (D). Manage cable as shown using covers on arm (A) and cable clip (F).
D
J

6
STEP 5
Adjust gas spring tension if needed by turning screw on top of center joint with 6mm Allen wrench (L).
L
L

7
Adjust as Desired
+90 °
-90°
±135 °
±90 °
±180 °
±180 °

LAST UPDATED: 03/06/2020
Open Monday - Friday 7:00am - 7:00pm CST,
our dedicated support team can oer immediate assistance with rapid response times. If any
parts are received damaged or defective, please contact us. We are happy to replace parts to
ensure you have a fully functioning product.
FOR MORE VIVO PRODUCTS, CHECK OUT OUR WEBSITE AT: www.vivo-us.com
[email protected] AVG. RESPONSE TIME (within oice hrs): 1HR 8M
- 23% within < 15m
- 38% within < 30m
- 61% within < 1hr
- 83% within < 2hr
- 92% within < 3hr
Love your new VIVO setup and want to share?
Tag us in your photo! @vivo_us
AVG. RESOLUTION TIME (within oice hrs): < 15 M
www.vivo-us.com
Chat live with an agent!
AVG. RESOLUTION TIME (within oice hrs): 5M 4S
309-278-5303