Vivo STAND-V200A User manual

Silver Pneumatic Arm Dual Monitor Desk Mount
Scan the QR code with your mobile device or follow the link
for helpful videos and specifications related to this product.
Instruction Manual
https://vivo-us.com/products/stand-v200a
SKU: STAND-V200A
[email protected]om www.vivo-us.com 309-278-5303
Chat live with an agent!
GET IN TOUCH | Monday-Friday from 7:00am-7:00pm CST

2
PACKAGE CONTENTS
TOOLS NEEDED
2.2-19.8lbs
(1-9kg)
DO NOT EXCEED WEIGHT CAPACITY.
Failure to do so may result in serious injury.
Phillips
Screwdriver
A (x1)
Arm
B(x1)
Clamp Brace
C(x1)
Clamp
J (x1)
Support Plate
NOTE: SOME HARDWARE INCLUDED MAY NOT BE USED
D(x1)
Cover
E(x2)
VESA Plate
F (x3)
M6x8mm
G(x4)
Pad
H (x1)
Carriage Bolt
I (x1)
Grommet Base
K (x1)
M8 Nut
M-A (x8)
M4x12
M-B (x8)
M5x12
M-C (x8)
D5 Washer
WARNING!
If you do not understand these directions, or if you have any doubts about the safety of the installation, please call a
qualified technician. Check carefully to make sure there are no missing or defective parts. Improper installation may
cause damage or serious injury. Do not use this product for any purpose that is not explicitly specified in this manual. Do
not exceed weight capacity. We cannot be liable for damage or injury caused by improper mounting, incorrect assembly
or inappropriate use.
TIPOVER WARNING
SERIOUS OR FATAL CRUSHING INJURIES CAN OCCUR FROM TIPOVER. TO HELP PREVENT TIPOVER:
• NEVER ALLOW CHILDREN TO CLIMB, STAND, HANG, OR PLAY ON ANY PART OF MONITOR OR
STAND.
• USE TIPOVER RESTRAINT OR ANCHOR STAND TO WALL
USE OF TIPOVER RESTRAINTS MAY ONLY REDUCE, BUT NOT ELIMINATE RISK OF TIPOVER.
WARNING: CHOKING HAZARD
SMALL PARTS - NOT FOR CHILDREN UNDER 3 YEARS. ADULT SUPERVISION IS REQUIRED.
O (x1)
6mm Allen
Wrench
L (x1)
M8 Washer
M (x2)
Cable Clip
N (x1)
4mm Allen
Wrench
P (x1)
Wrench
PER ARM

3
ASSEMBLY STEPS
STEP 1
OPTION A: Clamp Installation
Attach clamp brace (B) to the base of the
arm (A) using M6x8mm bolts (F), and
tighten with the 4mm Allen wrench (N).
Apply pads (G) to each corner of the base.
For 3/8” - 2” (10-50mm) desktop thickness,
place clamp (C) over the pre-installed
bolts in the clamp brace, then tighten bolts
using the 4mm Allen wrench (N).
For 1-3/4” - 3-11/32” (45-85mm) desktop
thickness, remove the screw and clamp
plate from the top of the clamp (C) hand
bolt. Remove the hand bolt, reinsert
through the other side, and reassemble the
clamp plate and screw. Place clamp over
the pre-installed bolts in the clamp brace,
then tighten bolts using the 4mm Allen
wrench (N).
Place the mount with clamp on the desk
edge and tighten the hand bolt. Place the
cover (D) on the back of the clamp.
OPTION B: Grommet Installation
Drop the carriage bolt (H) down through
the center hole of the grommet base (I),
making sure the counter-sink holes are
on the underside of the base. Attach
the grommet base with carriage bolt to
the base of the arm (A) using M6x8mm
bolts (F), and tighten with the 4mm Allen
wrench (N). Apply pads (G) to each corner
of the base.
If a grommet hole is not present in the
desktop, drill a hole through the desktop
using a 3/8” (10mm) bit. Place the arm
over the hole, then secure by attaching
the support plate (J) to the carriage bolt
protruding from underneath the desk
using the M8 nut (K) with M8 washer (L).
Tighten the M10 nut using the wrench (P).

4
STEP 2
Attach the VESA plates (E) to the monitors using
bolts (M-A or M-B) with washers (M-C), making
sure the knob on each is facing towards the
top of the monitor, and tighten with a Phillips
screwdriver.
STEP 3
Slide the VESA plates (E) with monitors onto the arm (A), and twist each knob 1/4
turn to lock.

5
STEP 4
If needed, adjust the gas spring in each arm (A) to
support the monitors using the 6mm Allen wrench
(O). While holding the arm in the straight forward po-
sition, turn the screw in back clockwise to decrease
support, and counter-clockwise to increase.
Attach the cable clips (M) to the arms, making sure they are firmly latched in place.
STEP 5
CAUTION - To avoid damage to the monitor
and mount, always keep the arm in a horizontal
position while making adjustments.

6
STEP 6
Use the cable clips (M) and cover (D) to organize cables.
STEP 7
To limit the arm swivel range, tighten the set screw on the back of the arm (A) using the flat blade
end of the 4mm Allen wrench (N). For no swivel range limit, loosen the set screw.

7
STEP 8
Tighten or loosen the rotation tension by turning the screws on the back of the VESA plates (E) with a
Phillips screwdriver. Adjust tilt support by turning the bolt on the side of the tilt joints with the 4mm
Allen wrench (N).

LAST UPDATED: 08/24/2020
Open Monday - Friday 7:00am - 7:00pm CST,
our dedicated support team can oer immediate assistance with rapid response times. If any
parts are received damaged or defective, please contact us. We are happy to replace parts to
ensure you have a fully functioning product.
FOR MORE VIVO PRODUCTS, CHECK OUT OUR WEBSITE AT: www.vivo-us.com
[email protected] AVG. RESPONSE TIME (within oice hrs): 1HR 8M
- 23% within < 15m
- 38% within < 30m
- 61% within < 1hr
- 83% within < 2hr
- 92% within < 3hr
Love your new VIVO setup and want to share?
Tag us in your photo! @vivo_us
AVG. RESOLUTION TIME (within oice hrs): < 15 M
www.vivo-us.com
Chat live with an agent!
AVG. RESOLUTION TIME (within oice hrs): 5M 4S
309-278-5303