Vivo STAND-V001V User manual

Single Monitor Desk Stand
Scan the QR code with your mobile device or follow the link
for helpful videos and specifications related to this product.
Instruction Manual
https://vivo-us.com/products/stand-v001v
SKU: STAND-V001V
[email protected]om www.vivo-us.com 309-278-5303
Chat live with an agent!
GET IN TOUCH | Monday-Friday from 7:00am-7:00pm CST

2
PACKAGE CONTENTS
A (x1)
Column
B(x1)
Base
C(x1)
VESA Plate
NOTE: SOME HARDWARE INCLUDED MAY NOT BE USED
D(x1)
Thumbscrew
E(x2)
Screw
F (x1)
Pad
G(x1)
4mm Allen
Wrench
H (x1)
6mm Allen
Wrench
M-A (x4)
M4x12
M-B (x4)
M4x16
M-C (x4)
M5x12
M-D (x4)
M5x16
M-E (x4)
D5 Washer
M-F (x4)
Spacer
WARNING!
If you do not understand these directions, or if you have any doubts about the safety of the
installation, please call a qualified technician. Check carefully to make sure there are no missing or
defective parts. Improper installation may cause damage or serious injury. Do not use this product
for any purpose that is not explicitly specified in this manual. Do not exceed weight capacity.
We cannot be liable for damage or injury caused by improper mounting, incorrect assembly or
inappropriate use.
TIPOVER WARNING
SERIOUS OR FATAL CRUSHING INJURIES CAN OCCUR FROM TIPOVER. TO HELP PREVENT TIPOVER:
• NEVER ALLOW CHILDREN TO CLIMB, STAND, HANG, OR PLAY ON ANY PART OF MONITOR OR
STAND.
• USE TIPOVER RESTRAINT OR ANCHOR STAND TO WALL
USE OF TIPOVER RESTRAINTS MAY ONLY REDUCE, BUT NOT ELIMINATE RISK OF TIPOVER.
WARNING: CHOKING HAZARD
SMALL PARTS - NOT FOR CHILDREN UNDER 3 YEARS. ADULT SUPERVISION IS REQUIRED.

3
ASSEMBLY STEPS
STEP 1
TOOLS NEEDED
15.4lbs
(6.99kg)
DO NOT EXCEED WEIGHT CAPACITY.
Failure to do so may result in serious injury.
Phillips
Screwdriver
STEP 2
Peel backing from pad (F) and stick in place over screws.
Mount telescopic column (A) to base (B) using screws (E). Tighten with 4mm Allen wrench (G).
A
B
E
G
F

4
STEP 3
OPTION B: Curved Back Monitor
Install VESA plate (C) to monitor using screws (M-B or M-D), washers (M-E), and spacers (M-F) if
necessary.
OPTION A: Flat Back Monitor
Install VESA plate (C) to monitor using short screws (M-A or M-C) and washers (M-E).
C
M- E
M- F
M- B
M- D
M-E
C
M-A
M-C

5
STEP 4
Slide monitor with VESA plate onto mounting bracket and secure with thumbscrew (D).
STEP 5
Adjust tilt support using 6mm Allen wrench (H).
D
H

6
STEP 7
Remove tape from lever. To raise or lower monitor, pull the lever up and adjust the monitor height.
Manage cables and store tools using pre-installed clip.
STEP 6
G
H
t ^o k fkd>

7
STEP 8
Press the lever down to lock the monitor height.
+20°
-20°
±45°
±180°

LAST UPDATED: 03/06/2020
Open Monday - Friday 7:00am - 7:00pm CST,
our dedicated support team can oer immediate assistance with rapid response times. If any
parts are received damaged or defective, please contact us. We are happy to replace parts to
ensure you have a fully functioning product.
FOR MORE VIVO PRODUCTS, CHECK OUT OUR WEBSITE AT: www.vivo-us.com
[email protected] AVG. RESPONSE TIME (within oice hrs): 1HR 8M
- 23% within < 15m
- 38% within < 30m
- 61% within < 1hr
- 83% within < 2hr
- 92% within < 3hr
Love your new VIVO setup and want to share?
Tag us in your photo! @vivo_us
AVG. RESOLUTION TIME (within oice hrs): < 15 M
www.vivo-us.com
Chat live with an agent!
AVG. RESOLUTION TIME (within oice hrs): 5M 4S
309-278-5303