Vivotek NR7401 User manual

EN - 1
English
Power off the Network Video Recorder
as soon as it is found smoking or
smelt unusual.
Contact your distributor when such cases
happen.
Keep the Network Video Recorder
away from the water. If the Network
Camera is wet, power off immediately.
Do not place the Network Video
Recorder around the heat sources,
such as television or oven.
Refer to your user's manual for the
operating temperature.
Keep the Network Video Recorder
away from direct sunlight.
Do not place the Network
Video Recorder in high humid
environments.
Power POE Status HDD WAN LAN1 LAN2 LAN3 LAN4 NR7401Network Video Recorder
Contact your distributor when such cases
happen.
Warning Before Install

EN - 2
Do not place the Network Video
Recorder on unsteady surfaces.
Do not touch the Network Video
Recorder when it's lightening.
Do not drop the Network Video
Recorder. Do not insert any object into the
Network Video Recorder, such as
needles.

EN - 3
English
Software CD
NR7401
Warranty card
3M Bumpon / screws
Quick installation guide
Power cord
Package Contents
1

EN - 4
Physical Description
2
Front Panel
Rear Panel
Power POE Status HDD WAN LAN1 LAN2 LAN3 LAN4 NR7401 Network Video Recorder
RESET
LAN4 LAN3 LAN2 LAN1 WAN
1 2 3 4 5 6 7 8 9101112
USB socket Status indicator
Power cord socket
Indented reset button
Ethernet 10/100
RJ45 socket
General I/O
terminal block

EN - 5
English
Before using the Network Video Recorder, please prepare a SATA hard disk to store the
recorded video.
1. Make sure the power is off.
2. Use a screwdriver to loose five screws, and then slide to remove the upper cover.
3. Loose the screw and take out the hard disk bracket.
4. Put your hard disk into the bracket, and secure it with the supplied four screws.
5. Place your hard disk into the Network Video Recorder.
6. Slide the hard disk as the picture shows, and then secure it with the original screw.
7. Attach the upper cover, and then secure it with the original five screws.
Hardware Installation
3
Install the hard disk
2
5
3
4
67

EN - 6
1. Connect the supplied power cable from the Network Video Recorder to a power outlet.
2. Connect NR7401 to Network Cameras and computer in LAN via LAN sockets. Because
NR7401 supports PoE, if the Network Camera is PoE-compliant, it allows transmission of
power and data via single Ethernet cable.
3. If your want to access NR7401 over the Internet, connect NR7401 to the Internet via
WAN socket.
4. If you have external devices such as sensors and alarms, make connections from gen-
eral I/O terminal block.
RESET
LAN4 LAN3 LAN2 LAN1 WAN
1 2 3 4 5 6 7 8 9101112
Activity
Power/MIC
Internet
WAN
LAN
LAN
LAN
1
2
Network Camera
(PoE)
Network Deployment
4
Network Camera
(without PoE)
3
1: Power
2: Relay output COM
3: Relay output N.O.
4: Digital Input 1
5: Digital Input 1 Ground
6: Digital Input 2
7: Digital Input 2 Ground
8: Digital Input 3
9: Digital Input 3 Ground
10: Digital Input 4
11: Digital Input 4 Ground
12: Ground
4
4
Cable, DSL
Modem, or router

EN - 7
English
3. Use the WAN IP address to access NR7401 from the Internet.
Assigning IP Address
5
1. Set up NR7401 in LAN. When in LAN, the default IP address for NR7401 is
192.168.100.1. Directly enter the IP address in the addrees bar of the web browser. The
webpage of NR7401 will be displayed for you to configure the settings.
2. If you want to access NR7401 over the Internet, please assign a WAN IP address in the
configuration page. There are three ways to get WAN IP address: DHCP (Dynamic IP),
Static IP address, and PPPoE (DSL).
If your network environment is DHCP, you can use VIVOTEK Installation Wizard 2 (IW2)
to get an IP address easily.
(1) Install the “Installation Wizard 2” under the Software Utility directory from software
CD.
(2) The program will conduct analyses on your network environment. After your network
is analyzed, please click on the “Next” button to continue the program.
Installation
Wizard 2
0002D107893F
0002D107893F
00-02-D1-07-89-3F 192.168.5.131 NR7401
(3) The program will search the VIVOTEK Network Devices in the same LAN.
(4) After searching, the main installer window will pop up. Click on the MAC that match-
es the one labeled on the bottom of your device to connect the Internet Explorer to
NR7401.

EN - 8
Note
If you want to record live video and playback the recorded video, you have
to add devices to NR7401 in the Configuration page. For further setup,
please refer to user's manual on the software CD.
Ready to Use
6
Following is the Homepage of NR7401.
Configuration page

P/N:625007300G