Vivotek FD8138-H User manual

IP Surveillance
Installation Guide
VIVOTEK Fixed Dome & Fisheye Series
Mounting Cap
Using AM-514 mounting cap
and compatible accessories
Rev. 1.0
Part no.: 625031700G
Ordering part no.:
100138800G ASS'Y KIT,AM-514_V01
625031700G_AM-514_ig_VVTK_rev1.0_20150910.indd 1 2015/9/10 上午 11:20:05
Available from A1 Security Cameras
www.a1securitycameras.com email: [email protected]

2
AM-514 Mounting Cap Mechanical Drawings
Revision History:
* Rev. 1.0: Initial Release
Compatible VIVOTEK Cameras
I
Fixed Dome series FD8167 / FD8138-H / FD9171 / FD816B / FD8182
Fisheye FE8174
You may also refer to VIVOTEK's website for the list of supported models. Support for other models can
be available through time.
Package Contents: AM-514, Installation Guide, 4x panhead M4x7, 2x copper spacer,
625031700G_AM-514_ig_VVTK_rev1.0_20150910.indd 2 2015/9/10 上午 11:20:05
Available from A1 Security Cameras
www.a1securitycameras.com email: [email protected]

3
English
Installation
II
Above are the locations of different groups of mounting holes for matching different junction
boxes:
Hole
Type
Applicable Box Drawings Screw No. of
screws
1
4" square box
#8-32, L15
(User-supplied) 2
2
4" octagon box
#8-32, L15
(User-supplied) 2
3
1" single gang box
#6-32, L15
(User-supplied) 2
Mounting Hole Denitions
User a hammer and screwdriver to open the
knock out holes you prefer to use.
625031700G_AM-514_ig_VVTK_rev1.0_20150910.indd 3 2015/9/10 上午 11:20:06
Available from A1 Security Cameras
www.a1securitycameras.com email: [email protected]

4
Installing the Mounting Cap
NOTE:
1. Route cables before you secure the accessories to a wall.
2. For details on the cable connections with network cameras, please refer to their Quick
Installation Guide.
Hole
Type
Applicable Cameras Screw No. of screws
AFD9171, FD816B,
FD8182 #8-32, L15 (User-supplied) 2
BFD8167, FD8138-H #8-32, L15 (User-supplied) 2
1FE8174 #6-32, L15 (User-supplied) + copper spacers 2
1. Route cables through the junction box.
625031700G_AM-514_ig_VVTK_rev1.0_20150910.indd 4 2015/9/10 上午 11:20:06
Available from A1 Security Cameras
www.a1securitycameras.com email: [email protected]

5
English
Hole 1
Hole 1
2. If installing FE8174 sheye camera, install two copper spacers to holes 1's.
3. Install the mount cap to the junction box. Use screw holes specied on page 3
depending on the type of junction box.
625031700G_AM-514_ig_VVTK_rev1.0_20150910.indd 5 2015/9/10 上午 11:20:06
Available from A1 Security Cameras
www.a1securitycameras.com email: [email protected]

6
4-1. FE8174.
4-1-1. Install the camera to the mount cap by fastening two screws to the threaded holes
on the copper spacers.
4-1-2. Connect the cables and install the top cover.
625031700G_AM-514_ig_VVTK_rev1.0_20150910.indd 6 2015/9/10 上午 11:20:08
Available from A1 Security Cameras
www.a1securitycameras.com email: [email protected]

7
English
4-2. FD9171/FD816B/FD8182.
4-2-1. Install the camera to the mount cap by fastening three screws. You will need to
remove the plastic tab on the routing hole in order to pass the cables.
4-2-2. Connect the cables and install the top cover.
625031700G_AM-514_ig_VVTK_rev1.0_20150910.indd 7 2015/9/10 上午 11:20:09
Available from A1 Security Cameras
www.a1securitycameras.com email: [email protected]

8
4-3. FD8167/FD8138H.
4-3-1. Fasten screws to the mounting cap. Do not completely tighten the screws. Leave
part of the screws out.
4-3-2. Install the camera to the mounting cap by turning it counter-clockwise so that the
screw heads t in the keyhole slots. Fasten the screws, and then connect the cables.
4-3-3. Install the dome cover. Tune the focus, and refer to the
documentation that came with your cameras for the rest of
conguration details.
625031700G_AM-514_ig_VVTK_rev1.0_20150910.indd 8 2015/9/10 上午 11:20:11
Available from A1 Security Cameras
www.a1securitycameras.com email: [email protected]