ViziT BVD-406 Series User manual

BVD-406x
BVD-406x VIZIT
BVD-406
FEATURES
DOOR OPEN
BVD-406x
VIZIT-M430C VIZIT -M460CM
VIZIT-ML300 -ML400
VIZIT-KTM600R(M) VIZIT-KTM602R(M)
SPECIFICATIONS
VDC 16…25
Wmax 6
Open drain
A 1.5
mm 95 x 150 x 37
kg 0.4
BVD-406VB BVD-406CB - 30 ... + 45°C
up to 98% at + 25°C
PARTS LIST
BVD-406x 1
1
1
1
doorstation is intended for use in videodoorphones.
The following models of are available:
Abbreviations used in the models names:
C - Colour camera;
V - B/W camera;
B - Board lens;
Cameras parameters are given below:
Calling a subscriber when the button is pressed
Duplex intercom between a visitor and subscriber
Entrance door unlocking by pressing the button on a subscriber’s monitor
Abeep during entrance door unlocking
Door zone videomonitoring
Illumination for the camera
Doorstation is intended for joint operation with:
- Monitors , or similar;
- Electromagnetic lock , ;
- Keys controller , .
Operating voltage, :
Power consumption, :
Lock control
Max. switchable current, :
Dimensions, :
Weight, :
Operating conditions
- ambient temperature range:
-
- relative humidity of air:
Doorstation pc
Mounting kit pc
Operating instruction pc
Package pc
=
=
=
=
=
=
A
,
Parameter
Lens
Angle of view (diagonal),°
uColo r system
Scanning system
Resolution, TVL
Output voltage,
Vpp @ 75 Ohm
Minimum illumination of an
object at 50 cm distance
from the camera, Lux
Model name
BVD-406CB BVD-406VB
“Board”
PAL
CCIR (EIA-optional)
CCIR
0.1
1 ± 0.15
-
³120
Model
name
Colour camera B / W camera
BVD-406CB
BVD-406VB
“Board” lens “Board” lens
Illumination
for the camera

SAFETY INSTRUCTIONS
25 VDC
INSTALLATION
ATTENTION!
BVD-406x
ATTENTION! min. 10 Ohms.
min. 20 Ohms.
The doorstation does not contain voltage above .
Do not make any connections or repair when the power is on.
Connect the grounding wire of the doorstation to the protective ground.
To maximize the reliability of this product, do not expose it to rain, snow or direct sun rays!
Before mounting, examine carefully the operating instruction for the installation order and wiring diagrams.
Mounting dimensions are shown on Figure 1 in millimeters.
The doorstation center should be approximately 1.5 meters above the floor.
Fix the doorstation on a door (Figure 2), using the screws and concrete inserts from the mounting kit.
Drive the gags into mounting holes.
Use 75-Ohm coaxial cable for video circuits to reduce external noises influence on image.
Fix the coaxial cable to back lid by means of a shackle.
Electromechanical lock impedance should be
Electromagnetic lock impedance should be
If an electromechanical lock is used, connect a damper diode (50V/1A, not supplied) to lock terminals.
Figure 1 - BVD-406 mounting dimensions
8 79
95
8134
150
12,5 70
13
124
29
37

FUNCTIONAL CHECK AND OPERATION ORDER
DOOR OPEN
DOOR OPEN
MONITOR
ABBREVIATIONS
Before switching the power on, verify all electric connections.
Turn the power supply on.
Press the button on the doorstation - a beep sounds at an apartment monitor while the button remains
pressed, image appears on the screen.
Pick up the handset and check duplex intercom.
Press the button on the monitor to release the lock; the doorstation produces a beep while the button
remains pressed. When the button is released, the system returns into intercom mode.
Hang up the handset. The system returns into STAND-BY mode.
The system returns into STAND-BY mode automatically in 60± 10 seconds after:
- picking up the handset
- the button pressing without picking up the handset
When called, a subscriber can press the button without picking up the handset to release the door lock.
The system returns into STAND-BY mode when the button is released.
Asubscriber can activate door zone videomonitoring (60 ± 10 seconds) just by pressing the button at any
time. The built-in camera or outdoor one provides video signal for the monitor.
During videomonitoring a subscriber can also activate duplex intercom by picking up the handset.
The system returns into STAND-BY mode either automatically in 60 seconds or after hanging up the handset.
LN Intercom line VO VIDEO OUT
GND GROUND VG VIDEO GROUND
+E Power for doorstation LC Lock Control
Ec Power for built-in camera
=
=
=
=
A
A
Figure 2 - Doorstation wall-mounting

Figure 3 - Doorstation with monitorBVD- 6CB (BVD-406VB) VIZIT-M430C
and electromechanical lock
40
-18
+18
+12
-12
50 V
1A
Power supply
BPD18/12-1-1
LN-
GND
LN+
VI1
+E
DATA
Ec1
Ec2
GND
VI2
Monitor
VIZIT-M430C
25 50 100
0.2 0.4 0.8
0.8 1.5
Min. cross-sections
of wires, mm2
1
2
3
4
5
1
2
2
1
1
2
12
2
1
A
B
C
D
Length
of cables
0.4
A+B
C+D
1
2
3
4
6
12
meters
Doorstation
BVD-406CB
(BVD-406VB)
LN
GND
+E
Ec
LC
VO
VG
6
5
Figure 4 - Doorstation with monitor
and button for exit
BVD- 6CB (BVD-406VB) VIZIT-M430C,
VIZIT-KTM600R, VIZIT-ML400
40
-12
+12
+18
-18
Power supply
BPD18/12-1-1
Doorstation
BVD-406CB
(BVD-406VB)
LN-
GND
LN+
VI1
+E
DATA
Ec1
Ec2
GND
VI2
Monitor
VIZIT-M430C
25
0.2 0.4
0.8
Min. cross-sections
of wires, mm
2
6
3
4
5
1
2
2
1
2
2
2
1
1
1
B
F
Length of
cables
0.4
A+B
C+D
1
2
3
4
5
1
2
meters
Control Unit
КТМ600М
-DL
+DL
+E
BIP
GND
RD
RG
OP
RF-keys
Reader
RD-3
Black
White
Blue
Red
A
D
E
C
Electromagnetic lock
VIZIT-ML400
Button
for exit
1
2
3
3
4
4
1
2
50
0.2 0.4E
0.2 0.4
F
LN
GND
+E
Ec
LC
VO
VG
1
6

Figure 5 - Doorstation with monitor
and button
BVD- 6CB (BVD-406VB) VIZIT-M430C,
VIZIT-KTM602R, VIZIT-ML400 “EXIT 300”
40
Control Unit
КТМ602М
-DL
+DL
BIP
ELC
RD
GND
OP
LN-
GND
LN+
VI1
+E
DATA
Ec1
Ec2
GND
VI2
Monitor
VIZIT-M430C
6
2
3
4
5
22
2
2
1
1
5
1
B
1
3
5
4
6
1
2
A
D
C
Electromagnetic lock
VIZIT-ML400
5
1
2
4
4
3
3
Red
Green
White
Black
Blue
Button
“EXIT 300”
25
0.2 0.4
0.8
Min. cross-sections
of wires, mm
Length of
cables
0.4
A+B
C
meters
50
0.2 0.4D+E
Black
White
Blue
Red
1
12
RF-keys
Reader
RD-3
2
E
21
21
Doorstation
BVD-406CB
(BVD-406VB)
LN
GND
+E
Ec
LC
VO
VG
12