ViziT BVD-403 Series User manual

BVD-403x
BVD-403х VIZIT
A
С
V
P
L BVD-403VPL
BVD-403CPL
BVD-403x VIZIT-ML400(S) VIZIT-ML300
VIZIT-KTM600R VIZIT-KTM602R
VIZIT®
VIZIT-M
FEATURES
SAFETY INSTRUCTIONS
25V
Connect the grounding wire of the doorstation to the protective ground.
Doorstation is intended for operation in video doorphones (Comfort Series).
The following models are available:
Abbreviations used in the models names:
- audio doorstation;
- colour camera;
- B/W camera;
- Pinhole lens;
- Camera illumination: IR LEDs for
White LEDs for
Doorstation operates together with electromagnetic locks , .
The product is compatible with similar electromagnetic locks with 20-Ohm impedance and a built-in degaussing
module.
Electromechanical locks with 10-Ohm impedance can be used as well.
Electromagnetic lock should be used together with
Keys Controller or .
Subscriber devices are products:
- apartment handsets (UKPs);
- monitors of Series 400.
Calls to the subscriber by pressing the button.
A beep at the doorstation and apartment handset / monitor when the button is pressed.
Duplex intercom.
Door zone video monitoring.
Camera LED illumination
Door unlocking by pressing the button on the apartment handset / monitor.
A beep indicates door lock release.
The product does not contain voltage above .
Do not make any connections or repair when the power is on.
Take care not to spill any liquids or chemically active substances on the product. Switch the power supply off, before
cleaning the doorstation. Clean by wiping with dry soft cloth. Do not use any liquid cleaners, aerosol cleaners or abrasive
agents.
·
·
·
·
·
·
·
A
A
Figure 1 - Doorstation BVD-403x
5Speaker
4CALL button
3Microphone
2LEDs for illumination
1Camera (for BVD-403CPL, VPL)
1
34
5
2
Model
B/W camera
BVD-403A
BVD-403CPL
Colour camera
Pinhole lens
BVD-403VPL
Illumination
for camera

INSTALLATION
Before mounting, examine carefully the operating instruction for the installation order and wiring diagrams.
The doorstation is mounted on a wall near your entrance door. The skew base provides 20° turn and allows either left-
side or right-side mounting.
Screw М4х12
Screw 2 - 4х25 Concrete Insert 6х30
BVD-403х Skew Base
Operating Instruction
x 1
x 1 x 1
Mounting parts
For BVD-403x and Skew Base
x 2
x 2
Washer 4
x 2
x 2
For grounding
Washer 3Screw М3
x 1 x 2
Nut М3 Loop Lug
x 1
x 1
Gag
x 4
PARTS LIST
2
3
1
4
Figure 1 - Doorstation wall-mounting (left-side position)
Mounting parts are supplied.
7
5
6
8
Hole ) 6 mm diameter 30 depth(х2
Insert 6х30 ( )х2
Screw 2- 4х25 ( )х2
Gag ( )х2
1
2
3
4
Doorstation
Skew Base
Metric Screw М4х12 ( )х2
Washer 4 ( )х2
8
5
6
7

Locate the doorstation to avoid:
- direct rays of the sun or other light sources
- direct hit of rain and snow
To reduce possibility of external noises influence on image, use 75-Ohm coaxial cable for video circuits.
Figure 3 - Wires, their assignment and order
Figure 2 - Doorstation wall- mounting (right-side position)
VO
Еc
LC
- Video Out
(for BVD-403CPL,VPL);
- Supply Voltage for
built-in camera;
- Lock Control.
LINE
GND
+Е
Ev
- Intercom Line;
- GROUND;
- Doorstation Supply Voltage;
- Supply Voltage for outdoor
camera (for BVD-403А)
Colour
GND +ELINE Ev/VO LC
Ec Grounding
wire
Figure 4 - Recommended doorstation position and camera field of view
34° 34°
150 сm
50 сm
50 сm
50 сm

Figure 5 - Doorstation with Apartment HandsetBVD-403A UKP-12(М)
Figure 6 - Doorstation with Outdoor Camera,
Monitor and Electromechanical Lock
BVD-403A
VIZIT-M430C
25 50 100
0.2 0.4 0.8
0.8 1.5
Cable
0.4
A
C+D
Length, m
0.2 0.4 0.8B
COLOUR
UKP-12(M)
Power Supply
BPD18/12-1-1
-18
+18
+12
-12
1
2
1
2
2
1
1
2
12
A
B
C
D
1
2
+
-
1
2
2
1
LINE
GND
+E
Ev
Ec
LC
Doorstation
BVD-403A
Cross-section, mm2
50 V
1A
Outdoor Camera
-18
+18
+12
-12
LN-
GND
LN+
VI1
+E
DATA
Ec1
Ec2
GND
VI2
3
4
1
2
2
1
1
2
12
A
B
C
D
1
3
4
12
2
1
2
VO
Ec
VG
1
2
E
1
2
2
1
VIZIT-M430C
Monitor
COLOUR
25 50 100
0.2 0.4 0.8
0.8 1.50.4
A+B+E
C+D
Cable Length, m
LINE
GND
+E
Ev
Ec
LC
Doorstation
BVD-403A
Power Supply
BPD18/12-1-1
Cross-section, mm2
50 V
1A

Figure 7 - with Monitor
and Electromechanical Lock
BVD-403CPL(VPL) VIZIT-M430C
Figure 8 - ,BVD-403CPL(VPL) КТМ602Мwith Control Unit Reader ,
Monitor , Electromagnetic Lock and Button
RD-3
VIZIT-M430С VIZIT-ML400 EXIT 300
Cross-section, mm2
-18
+18
+12
-12
LN-
GND
LN+
VI1
+E
DATA
Ec1
Ec2
GND
VI2
25 50 100
0.2 0.4 0.8
0.8 1.5
1
2
3
4
5
1
2
2
1
1
2
12
2
1
A
B
?
C
D
0.4
A+B
C+D
1
2
3
4
5
12
BPD
Power Supply
18/12-1-1
COLOUR
VIZIT-M430C
Monitor
Cable Length, m
50 V
1A
LINE
GND
+E
VO
Ec
LC
Doorstation
BVD-403CPL
(BVD-403VPL)
-DL
+DL
BIP
ELC
RD
GND
OP
LN-
GND
LN+
VI1
+E
DATA
Ec1
Ec2
GND
VI2
1
2
3
4
22
2
2
1
1
5
1
B
1
2
3
4
5
1
2
A
D
C
5
1
2
4
4
3
3
1
12
2
E
21
2
1
5
LINE
GND
+E
VO
Ec
LC
COLOUR
Reader RD-3
Black
White
Blue
Red
VIZIT-ML400
Elecrtomagnetic
Lock
Green
Button
EXIT 300
Black
White
Blue
Red
VIZIT-M430C
Monitor
Control Unit
КТМ602М
25
0.2 0.4
0.8
0.4
A+B
C
50
0.2 0.4D+E
Cable Length, m
Cross-section, mm2
Doorstation
BVD-403CPL
(BVD-403VPL)

FUNCTIONAL CHECK AND OPERATION ORDER
Note:
60 ± 5 seconds
SPECIFICATIONS
V 16...25
Wmax 3
mm 50x150x38
kg 0.3
OPERATING CONDITIONS
40°C 45°C
-30°C 45°C
98% 25 °C
Before switching the power on, verify all electric connections.
Turn the Power Supply on.
Press the button on the doorstation. A beep sounds at the doorstation and monitor /apartment handset while
the button remains pressed, image appears on the monitor’s screen.
Pick up the handset and check duplex intercom.
Check image on the screen. Adjust image brightness, contrast and saturation, if needed.
Press the button on the monitor / apartment handset to release the door lock. The doorstation produces a
beep while the button remains pressed. Release the button to return into intercom mode.
Hang up the handset. The system goes into STAND-BY mode.
When called, a subscriber can press the button without picking up the handset to release the door lock.
The system returns into STAND-BY mode when the button is released.
Intercom is available within after picking up the handset. The system returns into STAND-BY mode
automatically in 60 ± 5 seconds after picking up the handset or the button pressing without picking up the
handset.
A subscriber can activate door zone videomonitoring (60 ± 5 seconds) just by pressing the MONITOR button at any
time.
The built-in camera or outdoor one provides video signal for the monitor.
During videomonitoring a subscriber can also activate duplex intercom by picking up the handset.
The system returns into STAND-BY mode either automatically in 60 seconds or after hanging up the handset.
Operating voltage,
Power consumption,
Dimensions WxHxD,
Weight,
Camera parameters are given below:
Ambient temperature range
- BVD-403А from - to +
- BVD-403CPL(VPL) from to +
Relative humidity of air up to at
A
Camera parameters
Lens
Angle of view (diagonal),°
Colour system
Scanning system
Resolution, Tvl
Output voltage,
at 75 OhmVpp
Minimum illumination of an
object at 50 cm distance from
the camera, Lux
Doorstation BVD-403х
PAL
СCIR (EIA - optional)
СCIR
0.1
1 ± 0.15
-
BVD-403CPL
Pinhole
BVD-403VPL