ViziT VIZIT-C70 User manual

VIZIT-C70
VIZIT
SAFETY INSTRUCTIONS
30V
INSTALLATION
Locate the camera so as to avoid
OPERATING INSTRUCTION
:
()
.
.
-;
.
the camera hereinafter is intended for operation within video doorphones
as a surveillance device.
The product does not contain voltage above
Do not make any connections or repair when the power is on.
Take care not to spill any liquids or chemically active substances on the product.
Switch the power off before cleaning the product. Clean by wiping with dry soft cloth. Do not use any liquid cleaners,
aerosol cleaners or abrasive agents
direct rays of the sun or other sources of light
- direct hit of rain or snow
To reduce possibility of external noises affecting image on the screen, use coaxial cable RG-59 or similar for video lines.
Outdoor camera VIZIT-C70
For qualified installation, wiring and servicing refer to technical and commercial partners of VIZIT TM. The list of
companies is given on VIZIT.EU ( .http://vizit.eu/eurounion/)
VIZIT-C70 Operating Instruction
x1
PARTS LIST
x1
Fasteners
1 -Figure Outdoor camera VIZIT-C70
1Camera
2Illumination for camera
1
www. 201 -VIZIT-C70 revision 5 11vizit-group.com Operating Instruction ( ) 1/3
Gag
x 4
Self-tapping screw .53 х13
x 2
2
3Connecting cable
3
Figure 2 - Recommended camera position, and its field of view
50 cm
50 cm
68°
107cm
8cm0

The camera is mounted either on a fixed door leaf, or on a wall. Recommended location for the camera is above the
doorstation.
The camera may be powered from the below units:
control units of Series
- power supply units ;
- monitors .
Supply voltage circuits of the listed units shall be connected following the below table:
* - Control units of Series
-,
,,
,.
VIZIT ;
BPD BPD
VIZIT
VIZIT
300 400
18/12-1-1 24/12-1-1
300 400
CONNECTIONS
19 /14.4 / (1 /1. ) 19 /14.4 / (1 /1. )w v EU 2V 5A w v EU 8V 0A,
Figure Connection of5 - VIZIT-C70
GND
Eс
To commutators
To power supply unit
control unit BUD
or
monitor
,
VIZIT
Camera
VIZIT-C70
green
black
red
VO VG
*
red
black
green
- (Ес);
-();
-.
supply voltage for the camera
ground GND
video out (VO)
Colour and destination of the connecting
wires:
BUD*
Names of Terminals
+E
BPD18/12-1-1 BPD24/12-1-1
GND
+18V
-18V
+24V
GND
VIZIT-C70Circuit from
Ec
GND
www. 201 - /3vizit-group.com VIZIT-C70 Operating Instruction (revision 5 11) 2
Figure 3 Mounting on a fixed door leaf-
4
Hole
with diameter . mm
()
2 5
х2
Gags ( )х2
1
2
3
Camera VIZIT-C70
1
2
3
4
Self-tapping screw .53 х13 ( )х2
Figure Mounting on a wall4 -
4
Hole
with diameter 6 mm
and depth 40 mm
()х2
5
Anchor 46х 0 ( )х2
Screw 40- 4х ( )х2
Gag ( )х2
1
2
3
Camera VIZIT-C70
1
2
3
4
5
Note. Screws and anchors
are not supplied.
Monitor VIZIT
Ec1 (Ec2)
GND

SPECIFICATIONS
2 30 VDC
.W
84 mm
50 mm
40 mm
.2 kg
.25 kg
OPERATING CONDITIONS
-+
+
Operating voltage
Power consumption, no more than
Dimensions
width
height
depth
Net weight
Weight with package
Camera parameters are given in Table 2.
Table
Ambient temperature range to
Relative humidity of air: up to at
1 ...
1 5
0
0
30°C 45°C
98% 25°C
:
-
-
-
:
2
:
Camera Parameters
Angle of view (diagonal)
Colour system
Scanning system
Resolution
Minimal illumination
PAL
СCIR
700 TVL
0 Lux (IR LEDs are on
0.5 m range)
,
90°
Output voltage 1 Vp-p at Ohms75
Day-Night feature Yes
www. 201 - /3vizit-group.com VIZIT-C70 Operating Instruction (revision 5 11) 3