ViziT VIZIT-M441MG User manual

VIZIT-M44
OPERATING INSTRUCTION
VIZIT-M44 PAL
!
1MG
1MG
VIZIT
PARTS LIST
SAFETY INSTRUCTIONS
CAUTION 27V
is a colour monitor ( ) with a built-in memory for 64 B/W images. The Monitor is intended for use as
a subscriber device within video doorphones.
The Monitor does not contain voltage above .
Do not perform any connections or repair when the power supply unit is on. Take care not to spill any liquids or chemically
active substances on the product. Unplug the power supply unit before cleaning the Monitor. Clean by wiping with dry soft
cloth. Do not use any liquid cleaners, aerosol cleaners or abrasive agents.
Do not attempt to service the product by yourself. Please refer all services to qualified service personnel.
Figure Appearance and controls layout1-
Handset
Door Open button
Increase value / view next image button
Decrease value / view previous image button
On-screen menu button
AWAY mode LED indicator
Image capture button
Switch to additional camera button
MONITOR button
Power LED
Screen
AWAY mode button
www. 2016-0 )VIZIT-M441MG Operating Instruction (revision 7vizit-group.com 11/1
Figure Rear view2-
1
3
2
Connecting terminals (to video doorphone
and an outdoor camera)
DC IN to connect a power supply unit
19w/14.4v/EU(18V/1.0A)
Recess for cables
4
6
5
Inlets for cables
Battery cover
Socket for the handset jack
1
3
2
4
6
5
7
8
9
10
11
12
7Fixing lugs
Screw 3.5 25-х Anchor 6х30
x 3 x3
Fasteners
Operating Instruction
x1
x1
-44
Monitor
VIZIT M 1MG
Battery CR2032
1
7
3
9
2
4
5
10
12
11
6
8
Jumper
The jumper shall be set to position, if an
additional apartment handset UKP is
to the Monitor, or to position in
case of additional apartment handset UKP.
E
HS
E
QV./HS
QV.connected
no
8Terminals to connect an additional
apartment handset UKP
9
4
7
5
4
1
3
2
HS+
HS-
HSEQV.
6
7
8
9

FEATURES
v
v
v
v
v
v
v
v
v
v
v
v
v
v
v
Colour 3 5
Non-volatile memory for 64 B/W images
Non-volatile clock
Operation with two doorstations (BVD) and an outdoor camera when the Monitor is connected through the
Commutator BKM BKM BKM BKM
Operation with one doorstation Door Bell button outdoor camera and additional apartment handset UKP-7(M),
UKP-12(M), UKP-17(M) without the Commutator BKM
Calls from doorstations and a Door Bell button
Duplex intercom
Remote door unlocking with the button
Door zone video monitoring
Activation of an individual / storey doorstation(s) from the Monitor (duplex intercom and video monitoring)
On-screen menu
4 ring tones,
3 ring volume levels
LED indication of operating modes
. ” TFT LCD
-440, -440М, -441, -444.
,,
)
individual ring tone for each doorstation and Door Bell button
Individual image brightness, contrast and saturation for each doorstation and outdoor camera
Figure Installation order3-
Choose the place for the Monitor
Recommended altitude is cm above the floor
.
150 .
INSTALLATION
Drill three holes in the wall.
Drive anchors into the holes and fasten
screws (the fasteners are supplied with
the Monitor)
3
2
1
Connect wires to the Monitor terminals as
shown on Figures 4 - 9
Match the Monitor’s fixing lugs with the
screws in the wall and hook the Monitor on
the screws.
.
2
4
Connect the handset
jack to the Monitor’s
socket and hang up
the handset.
1
3
2
85
57
85
1
5
Take off the battery cover
Place the battery R inside the
battery compartment observing polarity
Put the cover back to its place.
.
C 2032
.
4
5
45
Set jumper to the
required position
if an additional apartment
handset UKP is to the
Monitor
QV. if there is additional
apartment handset UKP
:
- HS,
;
-E ,
.
EQV./HS
connected
no
3
HS+
HS-
HSEQV.
www. 2016-0 )VIZIT-M441MG Operating Instruction (revision 7vizit-group.com 21/1
For qualified installation, wiring and servicing refer to technical and commercial partners of VIZIT TM.
The list of companies is given on VIZIT.EU ( .http://vizit.eu/eurounion/)

The Monitor terminals and their destinations are given in the below table:
Where the Monitor operates together with the commutator , connection of a Door Bell button and additional
apartment handset UKP is not available. For details, refer to the commutator operating instruction.
Note BKM
BKM
.
See Fig. 4 - 9 for the of the Monitor and other doorphone units.
Acceptable cross-sections of wires to connect the Monitor to the power supply unit, doorstation / control unit (Fig. 4 - 5)
are given in the doorstation / control unit operating instruction.
Acceptable cross-sections of wires to connect the Monitor to the commutator (Fig. 6 - 9) are given in the
commutator BKM operating instruction.
examples of wiring diagrams
BKM
Terminal
LN +
LN -
GND
VI1
+E
DATA Data exchange between Monitor and commutator BKM
Supply voltage for Monitor
Video in from doorstation camera
Ground
Intercom line between Monitor and commutator /
doorstation
Destination
Ec1
Ec2
GND
VI2 Video in from outdoor camera
Ground
Supply voltage for outdoor camera
Supply voltage for doorstation camera
HS+
HS- Connection of additional apartment handset UKP
www. 2016-0 )VIZIT-M441MG Operating Instruction (revision 7vizit-group.com 31/1

Figure 5 Monitor with outdoor camera, additional UKP and Door Bell button
within individual (storey) video doorphone
-VIZIT-M441MG
LN- GND LN+
VI1
+E DATA Ec1 Ec2 GND
VI2
-44
Monitor
VIZIT M 1MG
HS
EQV.
HS+
HS-
VO
Ec
GND
Outdoor camera
12V . max/ 0 3А .
Door Bell
button
423 132
3
2
1
12
Additional
UKP
+
-
1
2
1
1
5
2
VO
Ec
LC
1
2
LINE
GND
+E 3
Doorstation
BVD 403CPL-
4
5
12
-18
+18
+12
-12
Power supply unit
BPD18/12-1-1
1
2
12
2
1
2
1
Electromechanical strike, or
V . max12 /0 6А .
electromechanical lock
1N4007
+DL
-DL
If an electromechanical lock / strike
has no built-in damper diode, the diode
shall be set additionally between
terminals of the lock /strike as shown
in the diagram.
EXAMPLES OF WIRING DIAGRAMS
Figure 4 - Monitor with outdoor camera, additional UKP and Door Bell button
within multi-apartment video doorphone
VIZIT-M441MG
LN- GND LN+
VI1
+E DATA Ec1 Ec2 GND
VI2
-44
Monitor
VIZIT M 1MG
Door Bell button may be installed
near the apartment door,
and connected between DATA
and GND terminals
GND +E
DC IN
HS
EQV.
HS+
HS-
18 , А
Power supply unit
19w/14.4v/EU(18V/1.0A)
V 1
VO
Ec
GND
Outdoor camera
12V . max./ 0 3А
Door Bell
button
14
3
2
1
4
3
2
VOA FA LN
GVOB FB LN GVOC FC LN GVOD FD LN G
FB FA+= FC FB+= FD FC+=
VO
VG
VG
VI
+E
G
LINE
GND
Ek
SEL
Commutator
BK 4AV-
Z
6
5
1
432 132
3
2
1
12
Additional
UKP
+
-
1
2
To next commutators
To next commutators
Intercom line
from main entrance
doorstation/ control unit
Protective conductor
Video line
from main entrance
doorstation
www. 2016-0 )VIZIT-M441MG Operating Instruction (revision 7vizit-group.com 41/1

Figure 6 - Monitor with outdoor camera and additional UKP
within multi-apartment and storey video doorphone
VIZIT-M441MG
HS+
Commutator
BKM-440
HS-
LN1-
GND
VI2
+E
L1N+
LN2-
VI1
LN2+
Ec1
Ec2
+E
GND
LN-
GND
LN+
+E
DATA
VO1
HS/MON
EQUIV
AB
C
VO2
GND
Additional
UKP
Storey
Doorstation
+
-
LN
GND
+E
Ec
LC
-BVD 406CB
VO
VG
To next commutators
To other apartments
VO
VG
VG
-18
+18
V1
FA
LN
VG
V2
FB
LN
VG
V3
FC
LN
VG
V4
FD
LN
VG
GND
LINE
SEL
Ek VI
Connect an Ohms resistor
to VO and VG terminals of the
last commutator in the circuit
82
Commutator
BK-4MV
-18
+18
+12
-12
Power Supply Unit
BPD18/12-1-1
Main Monitor
·
·
Individual / storey doorstation activation
Switching of video channels
Intercom priority over additional
apartment handset UKP
·
LN- GND LN+ VI1 +E DATA Ec1 Ec2 GND VI2
-44
Monitor
VIZIT M 1MG
HS
EQV.
HS+
HS-
VO
Ec
GND
Outdoor camera
12V . max./ 0 3А
245
132
3
2
1
163
245 163
Electromechanical lock, or
electromechanical strike
V. max12 /0 6А .
1N4007
+DL
-DL
If an electromechanical lock / strike
has no built-in damper diode, the diode
shall be set additionally between
terminals of the lock /strike as shown
in the diagram.
5
6
4
3
2
1
24 13
24 1346
2513
To main entrance doorstation /
control unit
www. 2016-0 )VIZIT-M441MG Operating Instruction (revision 7vizit-group.com 51/1

Figure Two monitors7 - VIZIT-M441MG with two individual / storey doorstations
Doorstation
BVD-401СВ
LN
LС
+E
Ec
VO
GND
HS+
Commutator
BKM-440
HS-
LN1-
GND
VI2
+E
L1N+
LN2-
VI1
LN2+
Ec1
Ec2
+E
GND
LN-
GND
LN+
+E
DATA
VO1
HS/MON
EQUIV
AB
C
VO2
GND
Additional
Monitor
Storey
Doorstation
Storey
Doorstation
·
·
Individual / storey doorstation
activation - not available
Switching of video channels -
not available
Main Monitor
·
·
·
Individual / storey doorstation activation
Switching of video channels
Intercom priority over additional
apartment handset UKP
LN- GND LN+ VI1 +E DATA Ec1 Ec2 GND VI2
-44
Monitor
VIZIT M 1MG
HS
EQV.
HS+
HS-
245 163
245 163
LN- GND LN+ VI1 +E DATA Ec1 Ec2 GND VI2
-44
Monitor
VIZIT M 1MG
HS
EQV.
HS+
HS-
245 13
24
513
-18
+18
+12
-12
Power supply unit
BPD18/12-1-1
1
2
12
2
1
Electromechanical strike, or
electromechanical lock
V . max12 /0 6А .
1N4007
+DL
-DL
1
2
3
4
5
2
1
LINE
GND
+E
VO
Ec
LC
Doorstation
BVD 405CP-1-
245 13
-18
+18
+12
-12
Power supply unit
BPD18/12-1-1
1
2
12
2
1
Electromechanical strike, or
electromechanical lock
V . max12 /0 6А .
1N4007
+DL
-DL
If an electromechanical lock / strike has no
built-in damper diode, the diode shall be set
additionally between terminals of the lock /
strike as shown in the diagram.
1
2
3
4
5
21
245 13
www. 2016-0 )VIZIT-M441MG Operating Instruction (revision 7vizit-group.com 61/1

Figure 8 - Two monitors with additional UKP
within multi-apartment and storey video doorphones
VIZIT-M441MG
1
2
3
4GND
VO
Ec
DATA
Doorstation
BVD 403CPO-
LN
GND
+E
Ec
LC
VO
VG
Doorstation
BVD-407RCB
OP
1
6
4
3
5
2
143
25 6
143
25 6
143143
25 6 143
2
Colour
2
12
2
1
2
1
-
+
Additional UKP
12
Commutator BKM-440М
HS.
EQUIV.
VI1 GND
LN1- +E
L1N+ GND
LN2- +E
LN2+
VI2
GND
VI3 Ec3 GND
DBB
+DL
Ec1
Ec2
+E
GND
LNM1-
VOM1
L1NM +
DATA_M1
+E
GND
LNM2-
VOM2
LNM2+
DATA_M2
HS-
HS+
C1Н CН2 CН3
CН4 CН5
CН6
LN- GND LN+ VI1 +E DATA Ec1 Ec2 GND VI2
-44
Monitor
VIZIT M 1MG
HS
EQV.
HS+
HS-
245 13
LN- GND LN+ VI1 +E DATA Ec1 Ec2 GND VI2
-44
Monitor
VIZIT M 1MG
HS
EQV.
HS+
HS-
245 13 6 6
to next
commutators
To next commutator
4
1
2
3
1
4
3
2
VOA
FA
LN
G
VOB
FB
LN
G
VOC
FC
LN
G
VOD
FD
LN
G
FB FA+= FC FB+= FD FC+=
VO
VG
VG
VI
+E
G
LINE
GND
Ek
SEL
Commutator
BK 4AV-
Z
6
5
to main entrance
doorstation /
control unit
Protective conductor
Electromechanical strike, or
V . max12 /0 6А .
electromechanical lock
+DL -DL
Video line
www. 2016-0 )VIZIT-M441MG Operating Instruction (revision 7vizit-group.com 71/1

Figure 9 - Monitor with Door Bell button
within multi-apartment and storey video doorphones
VIZIT-M441MG
1
4
3
2
5
6
To next commutators
BK-4MV
VO
VG
VG
-18
+18
GND
LINE
SEL
Ek VI
Commutator
BK-4MV
1
4
3
2
5
6
1
2
3
4
Doorstation
BVD 403CPL-
143
2
LINE
GND
+E
VO
Ec
LC
5
5
Door Bell
button
18 , А
Power Supply Unit
19w/14.4v/EU(18V/1.0A)
V 1
Commutator
BKM-441
VI1
GND
LN1-
L1N+
GND
LN2-
+E
LN2+
VI2
Ec2
+E
GND
LN-
VO
LN+
DATA
GND
+DL
DBB
GND +E
DC IN
14
23
To other apartments on the storey
V4
FD
LN
VG
V3
FC
LN
VG
V2
FB
LN
VG
V1
FA
LN
VG
14
3
2
Electromechanical strike, or
electromechanical lock
V . max12 /0 6А .
+DL -DL
LN-
GND
LN+
VI1
+E
DATA
Ec1 Ec2
GND
VI2
-44
Monitor
VIZIT M 1MG
HS
EQV.
HS+
HS-
245 13 6
To main entrance
doorstation /
control unit
www. 2016-0 )VIZIT-M441MG Operating Instruction (revision 7vizit-group.com 81/1

SETUP
Turn on the power supply unit or Commutator BKM.
Note.
Select a device (doorstation, or outdoor camera and door bell button) to make settings
Select a ring tone, set its volume*, adjust brightness, contrast and saturation of colour image. Set the
language, time and date, if needed
To select a setting
To set a ring tone RING SOUND MENU
MENU RING SOUND
To set a ring tone volume RING VOLUME MENU
MENU
RING VOLUME
To adjust image brightness, contrast and saturation MENU
MENU
Note.
To change menu language LANGUAGE MENU
To set date and time CLOCK MENU
MENU
MENU
OK MENU
CANCEL MENU
To quit menu OK MENU
Before turning the power on, make sure that there is no misconnection or risk of short circuit.
The Monitor’s Power LED (see Fig.1) illuminates with green light.
The Power LED may not illuminate at once, after turning the power on; the delay may take up to 7 seconds.
If in 7 seconds the Power LED is still dim, then the Monitor is in the sleep mode (calls are ignored, and all buttons
except for are disabled). To switch the Monitor on, push the button.
*Ring tone volume remains the same for both doorstations and door Bell Button, i.e. if you change ring tone volume for one
device, it will automatically change for the rest of connected devices.
, move the cursor bar up and down by pressing the and buttons.
(one of four), select ‘ ’ in the menu. the button, and the cursor bar jumps to the
current setting. or to select a new ring tone. Every time you press either or , the selected ring tone is
sounding. After you have chosen the ring tone, push the button. The cursor bar jumps back to ‘ ’.
(3 levels), select ‘ ’ in the menu. Push the button, and the cursor bar jumps
to the current setting. Push to decrease or to increase volume. Every time you push either or , the test sound is
ringing to present the volume level. After you have chosen the volume level, push the button. The cursor bar jumps
back to ‘ ’.
, select a corresponding line in the menu. Push the button,
and image from the selected device appears in the screen. In the lower part of the screen an adjustment bar is displayed. Set
a preferred value with the or buttons and push the button to return back to the main page.
If the buttons and are not pushed within about 15 seconds, the monitor automatically quits the menu.
, select ‘ ’ and push the button.
, select ‘ ’ in the menu and push the button. The menu goes to the next page:
Select a required line with or , and push the button, the cursor bar jumps to the current setting. Change the
settings with or , and push the button. The cursor bar returns to the
To save settings and return to the main page of the menu, select ‘ ’ and push the button.
To return to the main page without saving setting, select ‘ ’ and push .
, select ‘ ’and push the button.
·
·
·
1.
2.
3.
.
To select the doorstation connected directly to the Monitor, push the button.
The screen is showing image from the doorstation camera.
To select the doorstation and outdoor camera connected through the Commutator BKM, push the button
repeatedly until the screen shows image from the required device.
To select the outdoor camera with Door Bell button, push , and then .
The screen is showing image from the outdoor camera.
Having selected the device, push the button. The main page of on-screen menu appears on the screen.
Push
Push
MENU
menu line.
MENU
OK
Ring volume
Brightness
Contrast
Saturation
Clock
Ring sound 1
3
08
09
10
Language Eng
Cursor bar
Current
settings
Clock
Cancel
Year
Month
Date
Hours
Minutes
OK
11
10
21
10
30
Current
Settings
www. 2016-0 )VIZIT-M441MG Operating Instruction (revision 7vizit-group.com 91/1

Note. additional Monitor
Turn on the power supply unit or Commutator BKM.
Note.
Video monitoring initiated from the Monitor
Calls from the doorstation
Note
Activation of the individual doorstation
Calls from the Door Bell button or doorstation BVD
Note
Operation with an additional apartment handset UKP
Note. intercom priority Monitor’s
To engage the sleep mode press and hold until the Monitor LED is off.
Special notes on operation with Commutator BKM-440
main additional main
intercom priority main Monitor’s
main
If the Monitor is connected to the Commutator BKM as an (see Fig. 7), then individual settings
for the first and second doorstation are not available, the settings will be the same for both doorstations. To perform
settings, make a call to the Monitor from either connected doorstation. Then select a ring tone, set its volume, adjust
brightness, contrast and saturation as described above.
The Monitor’s Power LED (see Fig.1) illuminates with green light.
The Power LED may not illuminate at once, after turning the power on; the delay may take up to 7 seconds. If in
7 seconds the Power LED is still dim, then the Monitor is in the sleep mode (calls are ignored, and all buttons except for
are disabled). To switch the Monitor on, push the button.
To start video monitoring of door zone in front of the doorstation, push , or pick up the handset. Image from the doorstation
camera is displayed on the screen
To view door zone in front of the outdoor camera, push the button.
Where several doorstations are connected to the Monitor through the Commutator BKM, push the button repeatedly to
view door zone in front of the connected doorstations.
When a call is made from the doorstation, the Monitor is ringing. Image from the doorstation camera is displayed on the
screen. During intercom, push to view image from the outdoor camera
(see Fig. 4, 5, 6), if needed. Push again to switch back to the image from the doorstation camera.
To release the door lock, press and hold for 1 second (until a beep). The door is unlocked now. After you release the
button, intercom is still available. Hang up the handset. The screen will shut off, and the Monitor will go to stand-by.
You can unlock the door without picking up the handset. When called, just press and hold until the beep. The door
is unlocked now. After you release , the Monitor will go to stand-by.
To activate the individual / storey doorstation (i.e. start intercom and video monitoring on your initiative, see Fig. 5), pick
up the handset. Image is displayed on the screen, intercom is available. You can push to view image from the outdoor
camera, if needed. Push again to switch back to the image from the doorstation camera.
When the Door Bell button is pushed, the Monitor is ringing and the screen switches on displaying image from the outdoor
camera (see Fig. 4, 5).
Similarly when the call button on the doorstation BVD is pushed, the Monitor is ringing and the screen is
displaying image from the doorstation camera (see Fig.
If an additional apartment handset is connected to the Monitor, only the Monitor will be ringing, when a call is made
from the Door Bell button or doorstation BVD 403CPO
If an additional apartment handset is connected to the Monitor (see Fig. 4, 5), both the Monitor and apartment handset are
ringing when a call is made to the apartment. The Monitor’s screen is displaying image from the doorstation camera. Pick up
the UKP handset. The ringing will stop, and intercom with the doorstation will be available.
To release the door lock, push the lock release button on the UKP handset After you hang up the handset, the Monitor will
go on stand-by.
The Monitor has over the additional apartment handset, i.e. when you pick up the
handset during intercom, the additional UKP will be disengaged, and intercom will be set between the Monitor and
doorstation.
,
The Monitor can be connected to BKM-440 either as the or device (see Fig. 6, 7). The Monitor
has over any additional device, i.e. when you pick up the handset, the additional Monitor
or apartment handset UKP is disengaged. The additional Monitor cannot activate the individual / storey doorstation.
o view door zone in front of the main entrance doorstation (see Fig. 6), push the button on the Monitor.
To switch to viewing door zone in front of the individual / storey doorstation, push the button again.
FUNCTIONAL CHECK AND OPERATION ORDER
-403СРО
.
.
, -403СРО
8).
-.
.
T
.
Pick up the handset and check duplex intercom.
www. 2016-0 )VIZIT-M441MG Operating Instruction (revision 7vizit-group.com 10 1/1

Special notes on operation with Commutator BKM-440M
C1C2
C3
C1C2
Image capture
To capture visitor’s image during intercom
To set the Monitor on automatic image capture
Note.
Viewing captured images
-01
-02
Note.
SPECIFICATIONS
Ohms
W max
mm
OPERATING CONDITIONS
++
(see Fig. )
Both Monitors connected through BKM are not classified as main and additional devices (unlike with BKM-4 and
they remain fully equivalent in operation features.
To view door zone in front of the doorstations connected to , channels, and doorstation BVD-403CPO connected
to channel of BKM-440M (see Fig. 8), push repeatedly the button on either Monitor. The screen is displaying images
from the connected doorstations one by one. If one of the video inputs is vacant, i.e. not connected to any video device, it is
from viewing. Video monitoring is available from the both Monitors simultaneously.
If you are pushing the button with the , the screen is showing images from all cameras one by one,
though a vacant video channel is from viewing, showing a black screen.
To activate the doorstations connected to , channels, push the button on one of the Monitors until the screen is
displaying image you need, then pick up the handset.
When the handset is picked up from one of the Monitors, the other one gets blocked. It means that with picking up the
handset the Monitor’s screen will remain switched off, and short beeps will be sounding indicating the busy line.
When the handset is picked up from either Monitor, additional apartment handset will be disengaged.
, push the button on your Monitor, when image from the camera is on the
screen.
, push the button, when the Monitor is on stand-by. The LED indicator
for AWAY mode is illuminating. The Monitor captures image in 3 seconds after the call starts. The LED indicator is blinking,
if there are new images in the Monitor’s memory.
To quit automatic image capture mode, push the button, when the Monitor is on stand-by. The LED indicator for AWAY
mode will go out.
The Monitor’s memory is capable to store 64 images. If the memory is full, a new image will replace the oldest one in
the archive.
To start viewing captured images, push either or . The screen switches on and shows the newest captured image. In
the lower part of the screen there are time, date and number of the image displayed. The newest image has number .
The previous image has number , and so on.
Push either or to view the previous or next image respectively.
To quit viewing push .
The Monitor automatically quits viewing:
- in 40 seconds, if you do not push any button;
- when being called from the doorstation.
Captured images are always B/W disregarding the type of camera (either B/W or colour).
Screen
Video input
impedance
Power consumption
Dimensions (W)x(H)x(D)
The Monitor is intended for indoor use only.
Ambient temperature range to
Relative humidity of air: up to at
8
-440М 40),
:
:
-
:
НН
Н
НН
5°C 40°C
93% 25°C
automatically skipped
picked up handset
not skipped
-
Colour system
voltage
Operating voltage
Weight
3" mm
V p-p
VDC
.kg
.5 (89 ) TFT LCD
PAL
470
1…1.8
15…27
3
140х183х48
0 6
Colour: silver/dark grey
www. 2016-0 )VIZIT-M441MG Operating Instruction (revision 7vizit-group.com 11 1/1