VMP FP-XMF User manual

FP-XMF & FP-XMFB
Instruction Sheet For:
For more information, please contact us at:
345 Log Canoe Circle, Stevensville, Maryland 21666
Toll Free: 877.281.2169 Phone: [phone] Fax: [phone]
www.videomount.com

3
1
2
16
6
17 19
5
21
20
22
18
15 13 12
11
10
9
78
14
4
24
23
FP-XMF
ITEM
NO.
DESCRIPTION
QTY.
1
Wall Plate
2
2
Vertical Support
2
3
Screen Mounting Bracket
2
4
Cross Screw M4*P0.7*L6
6
5
Long Allen Key M4
1
6
Security Screw M5*P0.8*L20
2
7
Cross Screw M4*P0.7*L12
4
8
Cross Screw M5*P0.8*L12
4
9
Cross Screw M6*P1.0*L12
4
10
Cross Screw M8*P1.25*L16.5
4
11
Cross Screw M4*P0.7*L30
4
12
Cross Screw M5*P0.8*L30
4
13
Cross Screw M6*P1.0*L35
4
14
Cross Screw M8*P1.25*L40
4
15
Lock Washer M4
4
16
Lock Washer M5
4
17
Lock Washer M6
4
18
Lock Washer M8
4
19
Washer
5.5*
18*T2.0
4
20
Spacer M5
4
21
Spacer M8
4
22
Magnetic Level
1
23
Lag Screw 5/16"*2.5"
4
24
Washer
8.3*
19*T1.6
6

Step 1
Before starting, lay out all parts to your mount and match them to
the parts list provided. Verify that you have all your parts before
attempting to assemble the mount
Step 2
Assemble the wall plate by attaching the two horizontal wall plates
using the vertical supports and short M4 screws . You
can identify the difference between the top and bottom rail by the
fact that the top rail is the one with the stopper aps on either end.
Step 3
Mark the wall or desired mounting surface in preparation of instal-
lation of wall plate assembly ( and ). If mounting to wood-
en studs, pre drill pilot holes using a 7/32” drill bit. Attach the wall
plate assembly ( and ) to the wooden stud using the 5/16”
by 2.5” long lag screw and washer making sure the folded
tabs on the wall plate assembly are towards the top. WARNING:
Please verify that your mounting surface will support the combined
weight of your mount, mounting hardware, and at panel. Also
verify that the mounting surface is safe to drill through. Please note
only mounting hardware for mounting to wooden studs will be pro-
vided with the unit. If mounting to a surface other than wooden
studs then other hardware will be required. If in doubt or uncertain
about any of the above, please contact a professional installer.
Step 4
Determine the correct screw size and if you need to use washers,
lock washers, or spacers. Note: Spacers are used for TVs with re-
cessed hole patterns. Secure the TV to the mounting rails using
the appropriate hardware ( through ). Note: The brackets
have to be level with each other to work properly.
Step 5
Use the hooks in the mounting rails to hook on the top rail of
the wall plate assembly . Use security screws and the long
allen key to secure the TVs to the bottom rail and to secure
its horizontal position. Please verify that all nuts and screws are
securely tightened.
Step 2: Assembling the wall plate
Step 3: Mounting the wall plate
WARNING: The installer of these products must verify that the mount
surface, ceiling or wall, will safely support the combined weight of
all attached equipment and hardware. Video Mount Products will
not be held liable for the improper use or installation of its products.
Enjoy Your Mount!
2
1
6
4
5
Step 4: Attaching the mounting
brackets to the at panel
(spacers not needed)
Step 4: Attaching the mounting
brackets to the at panel
(spacers needed)
Step 5: Securing the mounting
brackets to the wall plate
2
1
3
21
1
3
7
24
23
1
2
1