VMP PM-LP User manual

PM-LP & PM-LPB
Instruction Sheet For:
For more information, please contact us at:
345 Log Canoe Circle, Stevensville, Maryland 21666
Toll Free: 877.281.2169 Phone: [phone] Fax: [phone]
www.videomount.com

215
3
1
517
6
22
6
7
20
14
813
911
10
25
12
16
4
24 23
18
19
27
26
PM-LP
ITEM
NO.
DESCRIPTION
QTY
.
1
Ceiling Plate
1
2
Socket Screw M6*P1.0*L20
4
3
Nylon Nut M6*P1.0
4
4
Feed Through Coupler
2
5
Outer Mast
1
6
Inner Mast
1
7
Upper Plate
1
8
Mid Plate
1
9
Lower Plate
1
10
Bottom Plate
1
11
Leg
4
12
Foot
4
13
Longer Foot
4
14
Socket Screw M6*P1.0*L12
16
15
Washer
6.4*
12*T1.6
16
16
Wing Screw M6*P1.0*L10
4
17
Hex Head Screw 5/16" -
18UNC*L2 1/2"
1
18
Nylon Nut 5/16" - 18UNC
1
19
Brake Screw 1/4" - 20UNC*L3/8"
2
20
M3 Allen Key
1
21
M4 Allen Key
1
22
Cross Screw M4*P0.7*L12
4
23
Cross Screw M5*P0.8*L12
4
24
Cross Screw M6*P1.0*L12
4
25
Plastic Bushings
4
26
Lag Screw 5/16"*L2.5"
4
27
Washer
8.3*
19*T1.6
4

Step 1
Before starting, lay out all parts to your mount and match them to the
parts list provided. Verify that you have all your parts before attempt-
ing to assemble the mount.
Step 2
Attach the feet or to the projector using the appropriate
screws or .
Step 3
Attach the feet or to the legs using the wing screws
Note: If you plan to feed the cables through the holes in the cen-
ter of the mount itself take the time to do so now before proceeding
further. Note: If using the longer feet use the M6 screws in
the rear holes of the feet in addition to the wing screws to better
secure the longer foot.
If you are using the flush mount plate:
Step 4
Attach the ceiling plate to the top of the upper plate using
the short socket head screws and washers .
Step 5
Mark the ceiling or desired mounting surface in preparation of instal-
lation of ceiling plate . If mounting to wooden ceiling joists, pre drill
pilot holes using a 7/32” drill bit. Attach the ceiling plate to the
wooden ceiling joist using the 5/16” by 2.5” long lag screw and
washer . Proceed to step 10. WARNING: Please verify that your
mounting surface will support the combined weight of your mount,
mounting hardware, and flat panel. Also verify that the mounting
surface is safe to drill through. Please note only mounting hardware
for mounting to wooden ceiling joists will be provided with the unit.
If mounting to a surface other than wooden ceiling joists then other
hardware will be required. If in doubt or uncertain about any of the
above, please contact a professional installer.
If you are using the ceiling plate:
Step 6
Attach the feed through coupler to the ceiling plate using
the longer socket screws , washers and nylon nuts .
Step 2: Attaching the feet to
the projector
Step 3: Attaching the feet to
the mount
Step 4: Attaching the mount
to the ceiling plate
Step 5: Attaching the
ceiling plate to the ceiling
15
1
3
15
12 13
2
14
1
7
4
16
Step 6: Attaching the feed
through couple to the ceiling
plate
22 23
12 13 11
16
13 24
11
27
26

Step 7
Mark the ceiling or desired mounting surface in preparation of in-
stallation of ceiling plate . If mounting to wooden ceiling joists,
pre drill pilot holes using a 7/32” drill bit. Attach the ceiling plate
to the wooden ceiling joist using the 5/16” by 2.5” long lag
screw and washer . WARNING: Please verify that your
mounting surface will support the combined weight of your mount,
mounting hardware, and flat panel. Also verify that the mounting
surface is safe to drill through. Please note only mounting hardware
for mounting to wooden ceiling joists will be provided with the unit.
If mounting to a surface other than wooden ceiling joists then other
hardware will be required. If in doubt or uncertain about any of the
above, please contact a professional installer.
Step 8
Attach the other feed through coupler to the top of the upper
plate using the shorter socket screws and washers .
Step 9
Screw the extension outer tube into the feed through couple
on the ceiling plate . Screw the extension inner tube
into the feed through couple on the upper plate . Tighten
brake screws into the threaded holes in the feed through
couples to secure the extension tubes in place. To adjust the
drop length of the mast, remove the 5/16” screw and slide the
inner tube so one of the other holes in the inner tube line up with
the holes in the outer tube. Then reinsert the 5/16” screw and
retighten the nylon nut .
Step 10
To adjust the tilt or pan of the projector, simply drag the projec-
tor to the desired position. If you have difficulty doing so, slightly
loosen the short socket screws that are in the plastic bushing
until desired tension is achieved to make tilting or panning eas-
ier. Cables may be ran through the center of the mount and the
ceiling mast either by using the holes in the feed though couplers
or the holes in the center of the mount and ceiling plate. Please
verify that all nuts and screws are securely tightened.
Step 7: Attaching the ceiling
plate to the ceiling
Step 8: Attaching the feed
through couple to the mount
Step 9: Connecting the mount
to the ceiling plate
WARNING: The installer of these products must verify that
the mounting surface, ceiling or wall, will safely support the
combined weight of all attached equipment and hardware.
Video Mount Products will not be held liable for the improper
use or installation of its products.
Enjoy Your Mount!
25
18
1
7
5
1
15
67
4
17
4
14
4
14
19
Step 10: Post installation
adjustment
17
1
26 27