VMP FP-MFTB User manual

FP-MFTB
Instruction Sheet For:
For more information, please contact us at:
345 Log Canoe Circle, Stevensville, Maryland 21666
Toll Free: 877.281.2169 Phone: [phone] Fax: [phone]
www.videomount.com

21
13
7
4
8
15
10
22
17 14
9
29
31
33 39 40
38
37
36
35
3432
30
28
27
26
25
24
23
16
11
19
6
18
20
1
3
2
5
12
FP-MFT
ITEM
NO.
DESCRIPTION
Qty
1
Wall Plate
1
2
Side Wall A
1
3
Side Wall B
1
4
Side Wall C
1
5
Side Wall D
1
6
Tilt Bracket
2
7
Top Hook
2
8
Leveler
2
9
Securement Bracket
2
10
Kick Stand
2
11
Socket Screw M8*P1.25*L20
4
12
Socket Screw M6*P1.0*L40
2
13
Screw M5*P0.8*L60
4
14
Screw M5*P0.8*L10
8
15
Washer
5.3*
10*T1.0
8
16
Screw M5*P0.8*L25
2
17
Screw M4*P0.7*L25
2
18
Spring Lock Washer M4
2
19
Hex Nut M4*P0.7
2
20
Pad
4
21
Long Allen Key M4
1
22
M5 Allen Key
1
23
Screw M4*P0.7*L12
4
24
Screw M5*P0.8*L12
4
25
Screw M6*P1.0*L12
4
26
Screw M8*P1.25*L16.5
4
27
Screw M4*P0.7*L30
4
28
Screw M5*P0.8*L30
4
29
Screw M6*P1.0*L35
4
30
Screw M8*P1.25*L40
4
31
Lock Washer M4
4
32
Lock Washer M5
4
33
Lock Washer M6
4
34
Lock Washer M8
4
35
Washer
5.5*
18*T2.0
4
36
Spacer M6
4
37
Spacer M8
4
38
Magnetic Level
1
39
Lag Screw 5/16"*L2.5"
4
40
Washer
8.3*
19*T1.6
4

Step 1
Lay out all parts to your mount and match them to the parts list
provided. Verify that you have all your parts before attempting to
assemble the mount.
Step 2
Before starting, make sure to tighten the socket screw at the top of
the tilt brackets as far as it will go to raise the brackets to the
maximum height. Also take this time to make sure the screws )
on the side of the top hook and the screws that attach
the securement bracket are just loose enough to slide freely
in their respective slots.
Step 3
Mark the wall or desired mounting surface in preparation of instal-
lation of wall plate . If mounting to wooden studs, pre drill
pilot holes using a 7/32” drill bit. Attach the wall plate to the
wooden stud using the 5/16” by 2.5” long lag screw and
washer (#40) making sure the folded tabs on the wall plate as-
sembly are towards the top. WARNING: Please verify that your
mounting surface will support the combined weight of your mount,
mounting hardware, and at panel. Also verify that the mounting
surface is safe to drill through. Please note only mounting hard-
ware for mounting to wooden studs will be provided with the unit.
If mounting to a surface other than wooden studs then other hard-
ware will be required. If in doubt or uncertain about any of the
above, please contact a professional installer.
Step 4
Determine the correct screw size and if you need to use washers,
lock washers, or spacers. Note: Spacers are used for TVs with re-
cessed hole patterns. Secure the display to the tilt brackets (#6)
using the appropriate hardware (#23 through #37). Note: The
brackets have to be level with each other to work properly. Note:
The socket screws (#11) on each bracket should be pointed to-
wards the outside of the at panel when attached to allow adjust-
ment of the tilt tension post installation.
Step 2: Starting adjustments
Step 3: Attaching the wall plate to
the wall
Step 4A: Attaching the at panel to
the tilt brackets (spacers not needed)
1
Step 4B: Attaching the at panel to
the tilt brackets (spacers used due
to recessed hole pattern)
12
14
714
9
1
39
40
6
23 37
11

WARNING: The installer of these products must verify that
the mount surface, ceiling or wall, will safely support the
combined weight of all attached equipment and hard-
ware. Video Mount Products will not be held liable for the
improper use or installation of its products.
Enjoy Your Mount!
Step 5: Securing the mounting
brackets
Step 5
To wire the at panel, pull the bottom of the at panel up
and lower the kick stand (#10on both tilt brackets. Attach
any cables and wires at this time to the at panel display.
When nished fold the kick stand (#10back up against the
tilt brackets to lower the at panel back to the wall plate .
Step 6
Check the securement brackets (#9) and make sure the
bottom lip of the wall plate (#1) is between the two metal
anges on the securement brackets. If not adjust the se-
curement brackets (#9) until this is true. Tighten the screw
(#16) in the bottom of the securement bracket (#9) until
the bracket is pressed rmly against the bottom lip of the
wall plate (#1). This step secures the tilt brackets to the wall
plate (#1).
Step 7
To adjust the vertical height of the unit unscrew the socket
screw (#12) at the top of the tilt brackets. To adjust the roll
of the unit for leveling purposes simply unscrew the same
screw (#12) on the side which you wish to lower until you
have achieved the desired height. Note: The further out of
level the two tilt brackets are the harder it will be to adjust
the higher side. If you nd it difcult to turn the higher side,
simply press up on the at panel on the higher side to relieve
the pressure to allow you to turn the screw easier.
Step 8
To adjust the tilt tension of the of the tilt brackets loosen or
tighten the socket screws (#11) on the side of the tilt brack-
ets until you have achieved desire tension.
Please verify that all nuts and screws are securely tightened.
Step 6: Engaging the securement
brackets
Step 7: Adjusting the height or roll of
the at panel
Step 8: Adjusting the tilt tension
on the tilt brackets
10
10
1
9
1
16 9
1
1
12
12
11
9