VMP LCD-CM2B User manual

LCD-CM2B
Instruction Sheet For:
For more information, please contact us at:
345 Log Canoe Circle, Stevensville, Maryland 21666
Toll Free: 877.281.2169 Phone: [phone] Fax: [phone]
www.videomount.com

LCD-CM2B
11
1 8
12 13 10
65
3 2 7 9
ITEM
NO.
DESCRIPTION
QTY.
1
Support Tube
1
2
Pivot Bracket
1
3
Small Mounting Plate
1
5
Nylon Nut M6*P1.0
1
6
Nylon Nut 3/8"-18UNC
1
7
Hex Screw M6*P1.0*L35
1
8
Adjustable Screw 1/4"-
20UNC*L2"
1
9
Cable Clip
2
10
Washer
10.2*
19*T1.6
2
11
Hex Screw 3/8"-18UNC*L2"
1
12
Cross Screw M4*P0.7*L12
4
13
Cross Screw M5*P0.8*L12
4

Step 1
Before starting, lay out all parts to your mount and match them to
the parts list provided. Verify that you have all your parts before at-
tempting to assemble the mount. Note: The LCD-CM2B and LCD-1CB
combo was designed to mount two of the same TV or TVs of similar
size and weight. It is not designed to have two significantly different
TVs mounted. Note: LCD-1CB part numbers have circles around their
numbers and LCD-CM2B has hexagons around their part numbers.
Step 2
Mark the ceiling or desired mounting surface in preparation of instal-
lation of ceiling plate (#1 LCD-1CB). If mounting to wooden ceiling
joists, pre drill pilot holes using a 7/32” drill bit. Attach the ceiling plate
(LCD-1CB) to the wooden ceiling joist using the 5/16” by 2.5” long
lag screw (#23 LCD-1CB) and washer ( LCD-1CB). WARNING:
Please verify that your mounting surface will support the combined
weight of your mount, mounting hardware, and flat panel. Also ver-
ify that the mounting surface is safe to drill through. Please note only
mounting hardware for mounting to wooden ceiling joists will be pro-
vided with the unit. If mounting to a surface other than wooden ceil-
ing joists then other hardware will be required. If in doubt or uncertain
about any of the above, please contact a professional installer.
Step 3
Insert end plugs (#14 LCD-1CB) into the support tube (# 1 LCD-CM2B).
Attach the pivot brackets (#2 LCD-CM2B and #4 LCD-1CB) to the
support tube (# 1 LCD-CM2B) using washers (#1 0 LCD-CM2B and #15
LCD-1CB) between the support tube (#1 LCD-CM2B) and the pivot
brackets (#2 LCD-CM2B and #4 LCD-1CB) and two inch hex screw
(#11 LCD-CM2B and #16 LCD-1CB) and nylon nut (#6 LCD-CM2B
and #8 LCD-1CB). Thread the adjusting screws (#12 LCD-1CB and
#8 LCD-CM2B) into the threaded hole in the bottom of the pivot
brackets (#2 LCD-CM2B and #4 LCD-1CB) until the bottom of the
screw is roughly even with the front of the pivot bracket.
Step 4
Attach the extension tube (#2 LCD-1CB) to the support tube (#1 LCD-
CM2B) using the large washers (#11 LCD-1CB) and M12 Screw (#10
LCD-1CB). Make sure the M12 screw (#10 LCD-1CB) is tight and once
it is tight secure the screw in place by tightening the brake screw (#17
LCD-1CB) in the threaded hole in the side of the extension tube (#2
LCD-1CB). Make sure the brake screw (#17 LCD-1CB) is as tight as
possible against the M12 screw (#10 LCD-1CB) to properly secure that
screw.
Step 2: Mounting the ceiling plate
Step 3: Attaching the pivot
bracket to the support tube
Step 4: Attaching the extension
tube to the support tube
14
1
23
1
24
10
1
24
115
1
24
11 16 6
812
8
4
2
21
11 10
10
2
17
17
10

Step 5
Use either the M4 (#22 LCD-1CB and #12 LCD-CM2B) or the M5 (#21
LCD-1CB and #13 LCD-CM2B) screws as appropriate for your flat
panels to attach your flat panels to the mounting plates (#5 LCD-
1CB and #3 LCD-CM2B).
Step 6
Through bolt the mounting plates (#5 LCD-1CB and #3 LCD-CM2B)
to the pivot brackets (#2 LCD-CM2B and #4 LCD-1CB) using the M6
screw (#9 LCD-1CB and #7 LCD-CM2B) and nylon nut (#7 LCD-1CB
and #5 LCD-CM2B).
Step 7
Determine the height at which you want to mount the flat pan-
els and through bolt the extension tube (#2 LCD-1CB) to the ceil-
ing plate (#1 LCD-1CB) at the appropriate height using the 5/16”
screw (#18 LCD-1CB) and nylon nut (#19 LCD-1CB).
Step 8
Insert cable clips (#13 LCD-1CB and #9 LCD-CM2B) into the sup-
port tube (#1 LCD-CM2B) for cable management. To adjust the tilt
of the flat panels thread the adjusting screw (#12 LCD-1CB and #8
LCD-CM2B) further into the pivot bracket (#2 LCD-CM2B and #4
LCD-1CB) to increase the tilt up and back to adjust the tilt down.
Please verify that all nuts and screws are securely tightened.
Step 5: Attaching the flat panel to
the mounting plate
Step 6: Attaching the mounting
bracket to the pivot bracket
Step 7: Attaching the extension tube
to the ceiling plate
Step 8: Final adjustments
WARNING: The installer of these products must verify that the mount sur-
face, ceiling or wall, will safely support the combined weight of all at-
tached equipment and hardware. Video Mount Products will not be held
liable for the improper use or installation of its products.
Enjoy Your Mount!
12
22
13
21
5
3
53
4
2
977
5
2
1
19
18
13 9
1
12 8
4
2