VMP LCD-2537C User manual

LCD-2537C & LCD-2537CB
Instruction Sheet For:
For more information, please contact us at:
345 Log Canoe Circle, Stevensville, Maryland 21666
Toll Free: 877.281.2169 Phone: [phone] Fax: [phone]
www.videomount.com

1
20
13
6
7
4
5
9
8
3
10
15
11
12
14
21
22
16
17
2
18
23 24
19
25
LCD-2537C
ITEM
NO.
DESCRIPTION
QTY.
1
Ceiling Plate
1
2
Extension Tube
1
3
Support Tube
1
4
Pivot Bracket
1
5
Small Mounting Plate
1
6
Large Mounting Plate
1
7
Nylon Nut M6*P1.0
1
8
Nylon Nut 3/8"-16UNC
1
9
Screw M6*P1.0*L40
1
10
Screw 3/4"-16UNF*L3"
1
11
Washer 3/4"*
44 2
12
Adjustable Screw 3/8"-
16UNC*L68mm
1
13
Cable Clips
2
14
End Plug
1
15
Washer
3/8"*
19*T1.6
2
16
Screw 3/8" - 16UNC*L2"
1
17
Brake Screw 1/4" - 20UNC*L1/2"
1
18
Screw 5/16" - 18UNC*L1-3/4"
1
19
Nylon Nut 5/16" - 18UNC
1
20
M3 Allen Key
1
21
Screw M5*P0.8*L12
4
22
Screw M4*P0.7*L12
4
23
Lag Screw 5/16"*L2.5"
4
24
Washer
8.3*
19*T1.6
4
25
Screw M6*P1.0*L12
4

Step 1
Before starting, lay out all parts to your mount and match them to
the parts list provided. Verify that you have all your parts before
attempting to assemble the mount.
Step 2
Determine which VESA standard plate you will be using or )
(75mm/100mm or 200mm/100mmx200mm respectively) and at-
tach the selected mounting plate or to the swivel bracket
using the M6 screw and the nylon nut .
Step 3
Attach the swivel bracket to the support tube using the
3/8” screw , washers and nylon nut . Insert adjust-
able screw into the back of the swivel bracket for use
when tilting the monitor.
Step 4
Mark the ceiling or desired mounting surface in preparation of in-
stallation of ceiling plate . If mounting to wooden ceiling joists,
pre drill pilot holes using a 7/32” drill bit. Attach the ceiling plate
to the wooden ceiling joist using the 5/16” by 2.5” long lag
screw and washer . WARNING: Please verify that your
mounting surface will support the combined weight of your mount,
mounting hardware, and flat panel. Also verify that the mounting
surface is safe to drill through. Please note only mounting hardware
for mounting to wooden ceiling joists will be provided with the unit.
If mounting to a surface other than wooden ceiling joists then other
hardware will be required. If in doubt or uncertain about any of the
above, please contact a professional installer.
Step 2: Attaching the mounting
plate to the swivel bracket (small
mounting plate (#5) shown)
Step 3: Attaching the swivel
bracket to the support tube
Step 4: Attaching ceiling plate
to ceiling
3
1
12
16
5
9
8
74
1
6
23 24
15
56
4
4

Step 5
Attach the support tube to the extension tube using
the ¾” screw and washers .
Step 6
Attach the mounting plate assembly from step 2 to your LCD
monitor using the M4 or M5 screws or as appropriate.
Step 7
Attach the extension tube to the ceiling plate using
the 5/16” screw and nylon nut . Secure the ¾” screw
from slipping in the extension tube by tightening the
¼” brake screw into the threaded hole in the side of the
extension tube using the Allen key .
Step 8
Insert end plugs into the support tube . For cable man-
agement, insert the cable clips by pushing the arrow ends
into the square holes in the support tube .
Please verify that all nuts and screws are securely tightened.
Step 5: Attaching the extension
tube to the support tube
Step 6: Attaching the flat panel
to the mounting plate
Step 7: Attaching the extension
tube to the ceiling plate
WARNING: The installer of these products must verify that
the mounting surface, ceiling or wall, will safely support the
combined weight of all attached equipment and hardware.
Video Mount Products will not be held liable for the improper
use or installation of its products.
Enjoy Your Mount!
2
17
20
2
19
10 11
18
2
1
21
32
14
22
10
13
3
3