VMP FP-LDSB User manual

FP-LDSB
Instruction Sheet For:
For more information, please contact us at:
345 Log Canoe Circle, Stevensville, Maryland 21666
Toll Free: 877.281.2169 Phone: [phone] Fax: [phone]
www.videomount.com

12 7
8
2
5
17
4
29
9
13
34
33
19 36
32
31
30
28
27
18
26
25
24
23
22
20
21
16
14
3
1
6
11
7
35
FP-LDSB
15
11
ITEM
NO.
DESCRIPTION
QTY.
1
Wall Plate
3
2
Connector Plate
3
3
End Cap
2
4
Screen Mounting Bracket
2
5
Tilt Plate
2
6
Cross Screw M6*P1.0*L60
2
7
Washer
8.3*
19*T1.6
6+6
8
Security Screw M5*P0.8*L20
2
9
Long Allen Key M4
1
11
Nylon Nut M8*P1.25
14
12
Extension A
2
13
Extension B
2
14
Square Neck Screw
M8*P1.25*L20
4
15
Nylon Nut M6*P1.0
16
16
Nylon Washer
8.5*
20*T2.0
4
17
Tilt Bushing
4
18
Magnetic Level
1
19
Washer
8.5*
20*T2.0
2
20
Screw M4*P0.7*L12
4
21
Screw M5*P0.8*L12
4
22
Screw M6*P1.0*L12
4
23
Screw M8*P1.25*L16
4
24
Screw M4*P0.7*L30
4
25
Screw M5*P0.8*L30
4
26
Screw M6*P1.0*L35
4
27
Screw M8*P1.25*L40
4
28
Lock Washer M4
4
29
Lock Washer M5
4
30
Lock Washer M6
4
31
Lock Washer M8
4
32
Washer
5.5*
18*T2.0
4+2
33
Spacer M5
4
34
Spacer M8
4
35
Cross Screw M8*P1.25*L65
2
36
Lag Screw 5/16"*L2.5"
6

Step 1
Before starting, lay out all parts to your mount and match them to the
parts list provided. Verify that you have all your parts before attempt-
ing to assemble the mount.
Step 2
Connect the desired amount of wall plates together using the
connector plates and nylon nuts .
Step 3
Mark the wall or desired mounting surface in preparation of installa-
tion of wall plate (#1). If mounting to wooden studs, pre drill pilot holes
using a 7/32” drill bit. Attach the wall plate (#1) to the wooden stud
using the 5/16” by 2.5” long lag screw (#36) and washer (#7) mak-
ing sure the small ear flaps are on the top rail of the wall plate (#1).
WARNING: Please verify that your mounting surface will support the
combined weight of your mount, mounting hardware, and flat panel.
Also verify that the mounting surface is safe to drill through. Please
note only mounting hardware for mounting to wooden studs will be
provided with the unit. If mounting to a surface other than wooden
studs then other hardware will be required. If in doubt or uncertain
about any of the above, please contact a professional installer.
Step 4
Attach the end caps to the ends of the wall plates using the
nylon nuts .
Step 5
If you need to extend the rails for mounting the flat panel display in
portrait then proceed with the following step. Otherwise proceed to
the next step.
Attach extension A and extension B using the nylon nuts .
Step 2: Connect the wall plates
together
Step 3: Mounting the wall plates
Step 4: Attaching the end caps
Step 5: Attaching the extensions
1
1
15
2
12 13 11
1
15
31
1
36 7

Step 6
If you wish to specify a tilt angle for the tilt brackets then proceed
with the following step. Otherwise proceed to the next step.
The tilt is lockable at 0°, 5°, 10° and 15°. The way you do this is for
0° line up the hole closest to the tilt arc on the screen mounting
bracket with the hole closest to the top square in the tilt plate
. Then insert the M6 screw through both the tilt plate and
the screen mounting bracket and use the nylon nut to lock
the tilt in place. For 5 degrees do the same, but with the next set of
holes down and so on for 10 and 15 degrees.
Step 7
Determinethecorrectscrewsizeandifyouneedtousewashers,lock
washers, or spacers. Note: Spacers are used for TVs with recessed
hole patterns. Secure the TV to the screen mounting bracket
using the appropriate hardware ( through ). Note: The
brackets have to be level with each other to work properly.
Step 8
Hookthe tiltplate onto the wall plates . Note: Make sure that
the wall plate that the tilt plate is hooked onto is secured into
the mounting surface. To secure the tilt plate to the wall plate
, tighten security screws in the threaded hole in the bottom
of the tilt plate using the long allen key . This will also secure
your horizontal positioning for the flat panel.
Step 9
To adjust the tension in the tilt mechanism to the desired level,
tighten/loosen the nylon nuts on the tilt arc.
Please verify that all nuts and screws are securely tightened.
Step 7B: Attaching the
mounting brackets to the
monitor (spacers used due to
recessed hole patterns)
Step 8: Securing the mounting
brackets to the wall plate
WARNING: The installer of these products must verify that the
mount surface, ceiling or wall, will safely support the com-
bined weight of all attached equipment and hardware. Vid-
eo Mount Products will not be held liable for the improper use
or installation of its products
Enjoy Your Mount!
Step 6: Locking the tilt in place
15
9
34
20
56
8
4
4
4
Step 7A: Attaching the mount-
ing brackets to the monitor
(spacers not needed)
5
11
5
5
5
1
5
11