Vogelzang International VG820E User manual

VGZ-010 / 20110513.1 VG820E HEARTWOOD™ / Page 1
READ ALL INSTRUCTIONS CAREFULLY
BEFORE STARTING THE INSTALLATION
OR OPERATING THE STOVE. FAILURE TO
FOLLOW INSTRUCTIONS MAY RESULT
IN PROPERTY DAMAGE, BODILY INJURY,
OR EVEN DEATH.
DO NOT USE THIS STOVE IN A
MOBILE HOME, TENT OR TRAILER.
(NO EXCEPTIONS)
This stove meets
U.S. Test Standard:
UL 1482-1996
SAFETY INSTRUCTIONS
SAFETY NOTICE: IF THIS STOVE IS NOT PROPERLY INSTALLED, A HOUSE/BUILDING FIRE MAY
RESULT. FORYOUR SAFETY, CONTACT LOCAL BUILDING OR FIRE OFFICIALS ABOUT PERMITS,
RESTRICTIONS, AND INSTALLATION REQUIREMENTS FOR YOUR AREA.
READ ALL INSTRUCTIONS CAREFULLY.
1. The installation of this stove must comply
with your local building code rulings. Please
observe the clearances to combustibles (see
reference figures 3 – 5).
2. Do not install this stove in a mobile home,
tent, or trailer (NO EXCEPTIONS).
3. Always connect this stove to a chimney and
vent to the outside. Never vent to another
room or inside a building.
4. DO NOT CONNECT a wood burning stove
to an aluminum Type B gas vent. This is not
safe. Use approved masonry or a UL 103 HT
Listed Residential Type and Building Heat-
ing Appliance Chimney. Use a 6” diameter
chimney or larger, that is high enough to give
a good draft. (See specifics in installation
instructions).
5. Be sure that your chimney is safely con-
structed and in good repair. Have the chim-
ney inspected by the fire department or a
qualified inspector.Your insurance company
may be able to recommend a qualified inspec-
tor.
6. Creosote or soot may build up in the chimney
connector and chimney and cause a house/
building fire. Inspect the chimney connector
and chimney twice monthly during the heating
season and clean if necessary. (See Chimney
Maintenance, page 10).
7. To prevent injury, do not allow anyone to use
this stove who is unfamiliar with the correct
operation of the stove.
8. Do not operate stove while under the
influence of drugs or alcohol.
9. For further information on using your stove
safely, obtain a copy of the National Fire
Protection Association (NFPA) publication,
“Using Coal and Wood Stoves Safely” NFPA
No. HS-10-1978. The address of the NFPA is
Batterymarch Park, Quincy, MA 02269.
Vogelzang International Corporation
400 West 17th Street
Holland, Michigan 49423
www.vogelzang.com
Phone: [phone] Fax: [phone]
Toll Free: 1-800-222-6950
HearTwOOd™wOOdsTOve
Model VG820E Owners Manual
(save this manual for future reference)
continued on page 2

Page 2 / VG820E HEARTWOOD™ VGZ-010 / 20110513.1
10. Ashes should not be allowed to accumulate
higher than the ash pan. Dispose of ashes in
a metal container with a tight fitting lid. Do
not include any other refuse. Keep the closed
container on a noncombustible floor or on the
ground, well away from all combustible materi-
als. Keep the ashes in the closed container until
all cinders have thoroughly cooled. The ashes
may be buried in the ground or picked up by a
refuse collector.
11. The special paints used on your stove may
give off some smoke and an odor while
they are curing during the first 12 to 15 fires.
Additional smoke and odor may be emitted
from the light oils used in construction of the
fire box. This should disappear after a short
period of time and not occur again. Persons
with lung conditions or owners of susceptible
domestic pets (such as birds) should take
prudent precautions. Open windows and
doors as needed to clear smoke and/or odor.
Paint discoloration will occur if the stove is
over fired.
12. This stove has a painted surface which
is durable but it will not stand rough handling
or abuse. When installing your stove, use care
in handling. Clean with soap and warm water
when stove is not hot. Do not use any acids
or scouring soap, as these solvents wear and
dull the finish.
13. While stove is in operation, all persons,
especially young children should be alerted to
the hazards from high surface temperatures.
Keep away from a hot stove to avoid burns
or clothing ignition. During operation, small
children should be carefully supervised when
they are in the same room as the stove.
14. Keep stove area clear and free from all
combustible materials, gasoline, and other
flammable vapors and liquids.
15. To prevent burns, always wear protective
clothing, leather hearth gloves and eye
protection, while tending the fire.
16. While in operation, keep the feed door, ash
door, and cabinet door closed and secured at
all times except while tending the fire.
17. Do not over fire the stove. Over firing will
occur if the feed door or ash door is left open
during operation. Such actions can result in
very dangerous operating conditions.
NOTE: A PROFESSIONAL, LICENSED HEAT-
ING AND COOLING CONTRACTOR SHOULD
BE CONSULTED IF YOU HAVE QUESTIONS
REGARDING THE INSTALLATION OF THIS
SOLID FUEL BURNING APPLIANCE.
SAFETY INSTRUCTIONS continued…
ASSEMBLY INSTRUCTIONS
t o o l s
Pencil
6 foot Folding Rule or Tape Measure
Tin Snips
Drill: Hand or Electric
1/8” dia. Drill Bit (sheet metal screws)
1/4” dia. Drill Bit (damper installation)
Screwdriver (blade & Phillips types)
6mm Nut Driver or Ratchet with 6mm Socket
Safety Glasses
Gloves
1. Uncrate the stove and remove cardboard pack-
ing and protective poly bag. (Save cardboard
for further assembly.)
2. Remove legs, upper and lower heat shields,
damper, and hardware pack from inside fire-
box.
3. Place flattened carton behind stove and care-
fully turn stove onto its back.
Fig. 1 Leg
& Heat Shield
Assembly
Upper Heat Shield
Lower Heat Shield
Leg
Assembly
TOOLS AND MATERIALS REQUIRED FOR INSTALLATION
m a t e r i a l s
(NOTE: The following items are NOT included with your stove)
Chimney Connection: 6” black steel (24 ga. min.) straight stove
pipe or elbow (as required)
1/2” Sheet Metal Screws
Chimney: Existing 6” Lined Masonry Chimney or 6” Inside Dia.
listed Type HT chimney.
Flooring Protection: 42” x 60” as specified (see page 3)
Furnace Cement (manufacturer recommends Rutland Code 78
or equivalent)

VGZ-010 / 20110513.1 VG820E HEARTWOOD™ / Page 3
4. Join the upper and lower heat shields with four
(4) self-tapping screws (fig. 1).
5. Place both legs upside down and attach the
heat shield assembly (from step 4) between the
legs.Align the holes in the heat shield assembly
with those in the mounting flange of the leg as-
semblies and secure with four (4) self-tapping
screws.
ASSEMBLY INSTRUCTIONS continued…
Fig. 2 Cabinet
Door Knob Assembly
LOCATING STOVE
1. The stove must be placed on solid concrete,
solid masonry, or when installed on a combus-
tible floor, on a listed floor protector, such as
Hy-C or Jackes-Evans Model UL 4260BK or
equivalent. (NOTE: To calculate R-values of
equivalent alternative materials, see page 14).
The base must extend at least 16” beyond the
side with the access door, 8” to the sides, 15”
to backside, and must extend under the stove
pipe if it is elbowed towards a wall. (See figures
3 & 4 and consult local building codes and fire
protection ordinances)
2. The stove must have its own flue. DO NOT
CONNECT THIS UNIT TO A CHIMNEY
FLUE SERVING OTHER APPLIANCES.
Fig. 3 – TOP VIEW Minimum Clearance Dimensions from Combustible Surfaces
FLOOR PROTECTOR
DASHED LINE SHOWS STRAIGHT
OUT CHIMNEY CONNECTOR
AND ADDITIONAL FLOOR
PROTECTOR REQUIRED
COMBUSTIBLE CONSTRUCTION IN
ACCORDANCE WITH NFPA 211
BACKWALL
SIDEWALL
15"
19"
42"
8"
8"
16"32"20"
60"
18"
34"
TOP VIEW
3. After observing the clearances to combustible
materials (figures 4 & 5), locate your floor
protector accordingly (figure 3) and care-
fully place the stove in your selected location.
Install stove pipe, elbows, and thimble as
required, utilizing either a recently cleaned
and inspected 6” masonry chimney or a 6” i.d.
listed chimney.
4. Use 6” r o u n d black stove pi p e , n o t
galvanized stove pipe. Secure pipe sections
with three (3) sheet metal screws in each stove
pipe and/or elbow joint to firmly hold the pipe
sections together. DO NOT CONNECT THIS
STOVE TO ANY AIR DISTRIBUTION OR
DUCT SYSTEM.
6. Attach leg/heat shield assembly to the base of
the stove using eight (8) self-tapping screws
(fig. 1).
7. Carefully lift stove to upright position.
8. Locate the door knob and machine screw in
the hardware pack. Open the cabinet door by
reaching under the cabinet frame
and pulling the door open.
9. Install the door knob onto the outside
of the door. Install the machine screw
through the latch bracket, door,
and into the knob. Tighten
securely (fig. 2).
WARNING: METAL PANELS FASTENED BE-
TWEEN LEGS ACT AS HEAT DEFLECTORS.
THESE PANELS MUST BE IN PLACE FOR SAFE
OPERATION.
Continued on page 4

Page 4 / VG820E HEARTWOOD™ VGZ-010 / 20110513.1
5. Recheck clearances from the stove,
connector stove pipe, and corner clearances
using the illustrations in figures 3 — 5 and
your local building codes or fire protection
ordinances.
NOTE: Drywall faced with brick or stone
should be considered a combustible surface.
6. DO NOT INSTALL THIS STOVE IN A MO-
BILE HOME, TENT OR TRAILER. (NO
EXCEPTIONS)
7. The clearances provided are minimum
dimensions determined by Warnock-Hersey,
the manufacturer’s testing laboratory. Instal-
lation of this stove must comply with the
latest edition of NFPA 211 for reduced clear-
ances and/or your local building code rulings.
Use whichever minimum dimensions are
LARGEST.
8. This stove meets U.S. Test Standard:
UL 1482-1996.
LOCATING STOVE continued…
FLOOR PROTECTOR FLOOR PROTECTOR
BACKWALL
SIDEWALL
20"
29" 16"
18"
15"
34"
Fig. 5a – Front View
Minimum Clearance Dimensions
from Combustible Surfaces
Fig. 5b – Side View
Minimum Clearance Dimensions
from Combustible Surfaces
CAUTION: KEEP FURNISHINGS AND OTHER
COMBUSTIBLE MATERIALS AWAY FORM THE
STOVE.
NOTE: BEFORE FIRING WOODSTOVE SLIDE
FIREBRICKS TOWARDS THE REAR SO NO
GAPS REMAIN BETWEEN BRICKS.
Fig. 4 – Top View
Minimum Corner Clearances
from Combustible Surfaces
24"
24"
CORNER
CLEARANCES
18"

VGZ-010 / 20110513.1 VG820E HEARTWOOD™ / Page 5
D-6 DRAFT DAMPER
A Draft Damper included with the stove must
be installed in the first straight section of pipe ex-
iting the stove before the stove pipe is connected
and the wood stove is used.
1. Drill two 1/4” holes centered on either side of
the pipe section 6” from the top end of the pipe
(figure 6).
2. Remove the handle from the damper then slide
the damper into the pipe.
3. Align the damper with the holes drilled in step
1 and insert the handle through the holes and
the damper.
NOTE: This damper is necessary for the proper
operation of the stove and to meet EPA
emissions requirements for heating appli-
ances. It MUST be installed before use.
(NO EXCEPTIONS)
6"/15.25 cm
CONNECTOR PIPE INSTALLATION
1. The crimped end of the stovepipe fits inside
the stove flue collar. Install additional pipe and
elbow with the crimped end towards the stove.
This will allow any condensation in the flue to
run back into the firebox.
2. Horizontal pipe runs must slope upwards
towards the chimney at least 1/4” per foot of
horizontal run.
3. You must have at least 18 inches of clearance
between any horizontal piping and the ceil-
ing.
4. The pipe cannot extend into the chimney flue
(figure 7).
5. Secure pipe/elbow sections with three (3) sheet
metal screws at each joint to make the piping
rigid.
6. It is recommended that no more than two (2)
90° bends be used in the stovepipe installa-
tion. The use of more than two 90° bends may
decrease the amount of draw and possibly
cause smoke spillage. Where possible, use only
corrugated (nonadjustable) elbows. These
provide a better seal.
7. The connector pipe must not pass through an
attic, roof space, trusses, closet, or any con-
cealed space, floor, ceiling, wall or combus-
tible construction. (See Chimney Connector
Systems & Clearances, page 15). A UL 103
HT Listed chimney must be used from the first
penetration of ceiling or wall to the chimney
cap. Never use single wall connector pipe as
a chimney – a house fire could result!
Fig. 6 – Draft Damper Installation
Fig. 7 – Stovepipe/Flue Connections
DRAFT DAMPER
(must be installed
before use — NO
EXCEPTIONS)
NOTE: STOVE PIPE IS NOT INCLUDED. TO
PURCHASE, VISIT YOUR LOCAL HARD-
WARE, HOME OR BUILDING CENTER. SEE
“LOCATING STOVE” PAGE 3 FOR ADDITIONAL
SPECIFICATIONS.
CORRECT WRONG WRONG

Page 6 / VG820E HEARTWOOD™ VGZ-010 / 20110513.1
CHIMNEY CONNECTIONS
Chimneys perform two functions.
1). As a means of exhausting smoke and flue
gases which are the result of fuel combustion.
2). The chimney provides “draft” which allows
oxygen to be continuously introduced into the ap-
pliance, so that proper combustion is possible.
As of April 1, 1987 all wood stoves should be
installed using a factory built chimney that meets
the “Type HT” requirement of UL 103 (when using
a factory built chimney).
NOTICE: Always provide a source of fresh air
into the room where the stove is located. Failure
to do so may result in air starvation of other fuel
burning appliances and the possible development
of hazardous operating conditions.
Note, your stove does NOT create draft. Draft
is a function of the chimney. A minimum of 0.05
w.c.,( measured in water column) is required for
proper drafting to prevent back-puffing, smoke
spillage, and to maximize performance. (Gauges to
measure chimney draft are readily available at stove
shops and are economical to purchase or rent.)
IMPORTANT Installation Points
1. Size the chimney flue to the stove pipe.
(6” outlet pipe = 6” chimney flue)
2. Use elbows only as necessary. Elbows
reduce draft, no more than two should be used
in any chimney run.
3. Make sure all horizontal runs of connec-
tor pipe have a minimum outward rise of 1/4” per
horizontal foot. This allows any condensation or
creosote buildup to run back into the firebox.
MASONRY CHIMNEY
Before using an existing masonry chimney,
clean the chimney, inspect the flue liner and make
any repairs needed to be sure it is safe to use. Make
repairs before attaching the stove. The connec-
tor stove pipe and fittings you will need to con-
nect directly to a masonry chimney are shown in
figure 8.
If the connector stove pipe must go through
a combustible wall before entering the masonry
chimney, consult a qualified mason or chimney
dealer. The installation must conform to local
building and fire codes and latest edition of NFPA
211.
Do not connect this stove into the same chim-
ney flue as the fireplace, gas appliance, or a flue
connected with any other stove. The chimney used
for a stove must not be used to ventilate the cellar
or basement. If there is a cleanout opening in the
base of the chimney, close it tightly.
CHIMNEY
FLUE
5/8" TILE
CHIMNEY
LINER
MASONRY
CHIMNEY
THIMBLE
COLLAR
6˝ ROUND
24 ga. BLACK
STOVEPIPE
8˝ MIN.
LINER
BELOW
ENTRY
HOLE
Fig. 9 - Chimney Construction Through Attic Space
Fig. 8 - Masonry Chimney Connection
LISTED CHIMNEY
Carefully follow chimney manufacturer’s
instructions. Use only a listed chimney. If your
chimney starts at the ceiling (figures 9 & 10) you
will need enough 6” round black stove pipe to reach
the ceiling. The top of the chimney must be at least
three (3) feet above the roof and be at least two (2)
feet higher than any point of the roof within ten
(10) feet (figure 9 – 11).

VGZ-010 / 20110513.1 VG820E HEARTWOOD™ / Page 7
Fig. 10 - Chimney Construction Through Roof
Fig. 11 - Chimney Connection to Firebox
Through Masonry Wall
CHIMNEY CONNECTIONS continued …
VENTING TO EXISTING FIREPLACE
In some instances, people desire to convert an
existing fireplace for stove use. Usually, safe con-
nection to an existing masonry chimney requires
more work than using a prefabricated chimney.
The existing fireplace must be closed and sealed at
the damper with high-temperature caulk, ceramic
wool, or furnace cement. Prior to installation, clean
and inspect the existing flue and smoke shelf. In-
stallation should be designed so the system can be
dismantled for periodic cleaning and inspection.
Before conversion, make sure the existing chimney
is structurally sound, the chimney incorporates a
flue liner and make sure it is in good condition.
(A flue liner consists of clay tile that protects the
brickwork of a chimney. If a chimney does not
have a liner, or it is damaged, have it relined by
a professional. DO NOT USE a chimney that is
unlined or damaged!) If you have any question
regarding the condition of the chimney, consult a
qualified licensed contractor, qualified engineer,
competent mason, certified Chimney Sweep, or a
knowledgable inspector. Consult your insurance
company if you cannot find a qualified expert.
CAUTION: Not all fireplaces are suitable
for conversion to a wood stove. Check
with a qualified expert.
Many prefabricated fireplaces are of the
“zero-clearance fireplace” category. These consist
of multilayered metal construction. They are de-
signed with enough insulation and/or air cooling
on the base, back and sides so they can be safely
installed in direct contact with combustible floors
and walls. Although many prefabricated fireplaces
carry endorsements from nationally recognized
organizations for use as fireplaces, they have not
been tested for connection to wood stove heaters.
Connecting a stove to such a device will void the
manufacturer’s warranty.
Steel-lined fireplaces are constructed with
1/4” firebox liner, an air chamber in connection
with 8” of masonry. These can be safely used with
wood burning stoves. They contain all the essential
components of a fireplace, firebox, damper, throat,
smoke shelf, and smoke chamber. Many look iden-
tical to masonry fireplaces and should be checked
Continued on page 8

Page 8 / VG820E HEARTWOOD™ VGZ-010 / 20110513.1
CHIMNEY CONNECTIONS continued …
carefully before connecting a stove to them.
Venting a stove directly into a fireplace does
not meet code and should not be attempted. (This
constitutes connection to another appliance - the
fireplace.) Combustion products will be deposited
and build up in the firebox or fireplace. The stove
warranty will be void with such an installation. Do
not create a hazard in your home by connecting in
this manner.
FIREPLACE INSTALLATION
Directly connecting the stovepipe into the exist-
ing masonry chimney (figure 12 “TypeA” fireplace
conversion) of the fireplace is the only approved
method of installation. This is a complicated and
involved process and to insure safety should only
by done by a qualified installer.
1. An entry hole must be cut through the masonry
and tile liner with minimal damage to the liner.
At least 8” of liner must remain below the entry
position. When locating the stove and stove-
pipe, all minimum clearances must be observed
from combustible surfaces including mantels,
combustible trimwork, ceilings and walls.
Positioning the center of the stove pipe entry
into the chimney 24” below the ceiling should
insure proper clearance for a 6” stovepipe.
2. Install a metal or fire clay (5/8” minimum thick-
ness) thimble. Make sure the thimble is flush
FIG. 12 - Fireplace Conversion
with the inner surface of the chimney liner and
does not protrude into the flue (see figure 7 on
page 4).
3. Secure the thimble with refractory mortar. The
thimble should be surrounded by 8” of solid
unit masonry brickwork or 24” of stone.
4. Install the stovepipe into the thimble as far as
possible without extending past the flue lining
(see figures 7 & 8 on pages 4 & 5).
5. A small airspace (about 1/2”) should remain
between the stovepipe and thimble to allow for
expansion of the pipe. Seal this airspace with
high-temperature caulking or ceramic wool.
6. Secure and seal the damper in the closed posi-
tion using high-temp caulking, ceramic wool,
or furnace cement. Also check to see if the
chimney has a cleanout. If it does, make sure it
is closed and sealed as well. A leaky cleanout
will greatly reduce draft efficiency.
If you have any questions regarding venting
your stove, contact the manufacturer or contact
the National Fire Protection Association (NFPA)
and request a copy of the latest editions of NFPA
Standard 211 and NFPA Standard 908. Their ad-
dress is:
Battery March Park, Quincy, MA 02269.

VGZ-010 / 20110513.1 VG820E HEARTWOOD™ / Page 9
OPERATING INSTRUCTIONS
This stove is designed to burn
WOOD FUEL ONLY.
Hardwood, 20” to 24” should be split and air
dried (seasoned), for 6 months to obtain maximum
burning efficiency. Wood should be stored in a dry,
well ventilated area.
NOTICE: USE SOLID WOOD MATERIALS ONLY.
DO NOT BURN GARBAGE OR FLAMMABLE
FLUIDS. DO NOT USE COAL AS COAL OR
CHARCOAL WILL DESTROY THE GRATES
AND/OR FIREBOX.
NOTE: Spin draft is factory set to meet EPA
regulations and is not adjustable. Draft
induction is controlled by thermostat setting
(see page 10).
LIGHTING
1. Set the thermostat on “HIGH” and open pipe
draft damper to provide maximum draft.
2. Using the separable handle, open the feed door
and place paper and kindling on the grate for
starting the fire.
3. Light fire, close feed door and secure tightly.
4. Add fuel after fire is burning briskly. Use care
not to smother the kindling fire when adding
wood.
5. Set the thermostat to maintain desired tem-
perature. “MEDIUM” setting is normally sat-
isfactory. Set higher or lower for your personal
comfort level.
ADDING FUEL
When possible, add small amounts of fuel each
hour or so instead of piling large quantities of fuel
every 4 to 5 hours. This will give a more complete
combustion process and less buildup of tars, soot,
or creosote will occur in the chimney.
1. Set thermostat to “HIGH” and open pipe draft
damper before opening the feed door.
2. Empty ash pan regularly. Do not allow ashes
to pile up higher than the sides of the ash pan.
If ashes build up to the grate, it can warp and
burnout will occur. If allowed to overfill, ashes
may spill when removing the pan.
3. Properly dispose of hot ashes (see Safety
Instructions, item #9 on page 2).
CAUTION: HOUSE FIRE HAZARDS
• Do not store wooD on floor
PROTECTOR, UNDERNEATH STOVEPIPE OR
ANYWHERE WITHIN MINIMUM CLEARANCES
FROM COMBUSTIBLE SURFACES SPECIFIED
FOR THIS STOVE. (36”)
• overfiring may cause a house fire.
YOU ARE OVERFIRING IF A UNIT OR CHIMNEY
CONNECTOR GLOWS RED.
• BuilD fires only on integral grate
INCLUDED WITH THE STOVE.
WARNING: EXPLOSION HAZARD
• never use chemicals, gasoline,
GASOLINE-TYPE LANTERN FUEL, KEROSENE,
CHARCOAL LIGHTER FLUID, OR SIMILAR
FLAMMABLE LIQUIDS TO START OR “FRESH-
EN-UP” A FIRE IN THE STOVE.
• K e e p  a l l  f l a m m a B l e  l i q u i D s ,
ESPECIALLY GASOLINE, OUT OF THE
VICINITY OFTHE HEATER — WHETHER IN USE
OR IN STORAGE.
OPERATING SAFETY PRECAUTIONS
1. NEVER OVERFIRE THIS STOVE BY BUILD-
ING EXCESSIVELY HOT FIRES AS A HOUSE/
BUILDING FIRE MAY RESULT.YOU ARE OVER-
FIRING THE STOVE IF UNIT OR STOVEPIPE
BEGINS TO GLOW OR TURN RED.
2. NEVER BUILD EXTREMELY LARGE FIRES
IN THIS TYPE OF STOVE AS DAMAGE TO THE
STOVE OR SMOKE LEAKAGE MAY RESULT.
3. UNIT IS HOT WHILE IN OPERATION. KEEP
CHILDREN, CLOTHING, AND FURNITURE AWAY.
CONTACT MAY CAUSE SKIN BURNS. DO NOT
TOUCH THE STOVE AFTER FIRING UNTIL IT
HAS COOLED.
4. PROVIDE AIR INTO THE ROOM FOR PROP-
ER COMBUSTION.
5. INSPECT STOVEPIPE EVERY 60 DAYS.
REPLACE IMMEDIATELY IF STOVEPIPE IS
RUSTING OR LEAKING SMOKE INTO THE
ROOM.
Continued on page 10

Page 10 / VG820E HEARTWOOD™ VGZ-010 / 20110513.1
OPERATING INSTRUCTIONS continued …
THERMOSTAT
The thermostat controls the rate of burn by opening or closing a draft damper on the lower front of
the firebox. The thermostat control was calibrated at the factory and is not adjustable. The thermostat
is mounted behind the front control panel and the damper is mounted to the lower front of the firebox.
The cabinet lid may be opened (when stove has cooled) for access to these components.
CAUTION:DO NOT OPEN OR CLOSETOPWHEN
HEATER IS HOT!
1. To open, when stove has cooled grasp the
cabinet top at front (figure 13A) and lift all the
way up.
2. Gently lower the top until the top support
rod latches to hold the top in the up position
(figure 13B).
3. To close, lift the top until the support rod
is unlatched.
4. Pull the support rod forward as you lower
the cabinet top.
If the room temperature is not satisfactory,
check the following items.
To decrease the amount of heat at
“LOW” setting:
1. Check feed and ash doors to be sure that
they are closed and secured tightly.
2. Check the connector pipe to see that it is
sealed in the flue collar and at all joints.
3. Make sure the flue draft damper is fully
closed.
Fig. 13
Thermostat Access
Fig. 14
Thermostat / Damper
Minimum Fire
The rate of burning at the “LOW” thermostat
setting can be further controlled by adjusting the
flue draft damper.
1. Fully close the thermostat and draft damper to
make the fuel burn longer.
2. To increase rate of burn turn up the thermostat
or open the draft damper. This will help reduce
the formation of creosote or soot (see notes on
Chimney Maintenance, page 11.)

VGZ-010 / 20110513.1 VG820E HEARTWOOD™ / Page 11
SERVICE HINTS
DRAFT is a function of the chimney, not the
stove — do not expect the stove to draw. Smoke
spillage into the house or excess buildup of conden-
sation or creosote in the chimney are warnings that
the chimney is NOT functioning properly. Correct
the problem before using the stove. Following are
some possible causes for improper draft.
1. The connector stovepipe may be pushed
into the chimney too far, stopping the draft.
2. If the chimney is operating too cool, water
will condense in the chimney and run back into the
stove. Creosote formation will be rapid and may
block the chimney. Operate the stove at a fire level
high enough to keep the chimney warm preventing
this condensation.
3. If the fire burns well but sometimes creates
excessive smoke or burns slowly, it may be caused
by the chimney top being lower than another part
of the house or a nearby tree. The wind blowing
over a house or tree, falls on top of the chimney like
water over a dam, beating down the smoke. The
top of the chimney should be at least three (3) feet
above the roof and be at least two (2) feet higher
than any point of the roof within ten (10) feet.
NOTE: A DRAFT READING OF 0.05 TO 0.06
W.C. (WATER COLUMN) IS SUGGESTED FOR
PROPER BURNING OF THIS STOVE.
CHIMNEY MAINTENANCE
CREOSOTE – Formation and Removal
When wood is burned slowly, it produces tar
and other organic vapors which combine with
expelled moisture to form creosote. The creosote
vapors condense in the relatively cool chimney
flue of a slow-burning fire. As a result, creosote
residue accumulates on the flue lining. If ignited,
this creosote creates an extremely hot fire which
may ignite surrounding materials resulting in a
building fire.
The chimney connector and chimney should
be inspected at least twice a month during the
heating season to determine if a creosote buildup
has occurred.
If creosote has accumulated, it should be
removed. Failure to remove creosote may result
in ignition and may cause a house/building fire.
Creosote may be removed using a chimney brush
or other commonly available materials from your
local hardware retailer.
Chimney fires burn very hot. If the unit or
chimney connector should glow red, reduce the
fire by closing the inlet air control and immediately
call the fire department.
CAUTION: A CHIMNEY FIRE MAY CAUSE IGNI-
TION OF WALL STUDS OR RAFTERS WHICH
WERE ASSUMED TO BE A SAFE DISTANCE
FROM THE CHIMNEY. IF A CHIMNEY FIRE
HAS OCCURRED, HAVE YOUR CHIMNEY IN-
SPECTED BY A QUALIFIED EXPERT BEFORE
USING AGAIN.
A fire in the firebox may be smothered by pour-
ing a large quantity of coarse salt, baking soda, or
cool ashes on top of the fire.

Page 12 / VG820E HEARTWOOD™ VGZ-010 / 20110513.1
ORDERING PARTS - VG820E HEARTWOOD STOVE
When ordering missing or replacement parts, always give the Model Number of the stove, Part
Number, and Part Description. Use the illustrations and part lists provided on the following pages
to identify parts.
Part No. Description Qty. Part No. Description Qty.
12 Hinge, Door............................................... 4
13 Back Brace................................................ 2
14 Thermostat Assembly ............................... 1
15 Chain Linkage, Thermostat ....................... 1
16 Top Shield, Thermostat ............................. 1
17 Screw, No.10 Torx ..................................... 2
18 Knob, Thermostat...................................... 1
19
20 Support, Hinge.......................................... 1
21 Clip, Hinge ................................................ 1
1 Cabinet Top ............................................... 1
2 Cabinet, Back............................................ 1
3 Cabinet, Left Side ..................................... 1
4 Cabinet, Front Assembly........................... 1
5 Cabinet, Door Frame................................. 1
6 Cabinet, Door............................................ 1
7 Knob, Cabinet Door................................... 1
8 Screw, 8-32x1/4” Machine......................... 1
9 Latch, Spring............................................. 1
10 Nut, 10-24 ................................................. 8
11 Screw, 10-24x1/2” Flat Hd......................... 8

VGZ-010 / 20110513.1 VG820E HEARTWOOD™ / Page 13
ORDERING PARTS - VG820E HEARTWOOD STOVE
When ordering missing or replacement parts, always give the Model Number of the stove, Part
Number, and Part Description. Use the illustrations and part lists provided on the following pages
to identify parts.
Part No. Description Qty.
22 Firebox Assembly...................................... 1
23 Firebrick ................................................... 10
24 Liner, Front & Rear.................................... 3
25 Leg............................................................ 2
26 Heat Shield, Upper.................................... 1
27 Heat Shield, Lower.................................... 1
28 Draft Control.............................................. 1
29 Clip, Spring ............................................... 1
30 Frame, Draft Damper ................................ 1
31 Pin, Draft Damper ..................................... 1
32 Support, Grate & Liner.............................. 2
33 Retainer, Top Brick .................................... 2
34 Fire Grate.................................................. 2
35 Shield, Front.............................................. 1
36 No. 10x1/2” Torque H.D. ............................ 2
37 Ash Pan Assembly.................................... 1
38 Damper Assembly (flue mount) ................ 1
39 Smoke Curtain .......................................... 1
40 Bracket, Smoke Curtain ............................ 1
Part No. Description Qty.
41 Screw, 1/4-20x3/4” Flat Hd........................ 1
42 Nut, 1/4-20 ................................................ 1
43 Door, Ash .................................................. 1
44 S-Hook (to hang separable handle) .......... 1
45 Gasket, 29” Ash Door................................ 1
46 Door Assembly, Feed................................ 1
47 Handle, Separable (Spring) ...................... 1
48 Handle....................................................... 2
49 Latch, Door ............................................... 2
50 Spacer....................................................... 2
51 Screw, 1/4-20x3/4” Mach .......................... 1
52 Pin, Keeper ............................................... 1
53 Gasket, 45” Feed Door.............................. 1
54 Pin, Door Hinge......................................... 4
55 Liner, Top................................................... 1
56 Nut, 1/4-20 Kep......................................... 6
57 Screw, 1/4-20x3/4” Flat Hd........................ 6
58 Flue Collar................................................. 1
59 Gasket....................................................... 1

Page 14 / VG820E HEARTWOOD™ VGZ-010 / 20110513.1
FLOOR PROTECTOR MATERIAL CALCULATIONS
This stove has been tested for and must be installed on a floor protector with the proper Thermal
Resistance or R-value as stated in the installation instructions on page 3, “Locating Stove” step 1, of
this manual. If the floor protector materials listed in the instructions are not available, materials with
an equivalent R-value may be substituted.
Alternate materials may be rated with C-factor (Thermal Conductance) or k-factor (Thermal
Conductivity) ratings which must be converted to R-value to determine if the alternate material meets
the tested requirements. The following instructions provide the proper information and formulas for
conversion to R-value.
To determine if alternate materials are acceptable follow this sequence.
1. Convert material specifications to R-value:
a. R-value given — no conversion necessary
b. k-factor is given with a required thickness (T) in inches:
R = 1/k x T
c. C-factor is given: R = 1/C
2. Determine the R-value of proposed alternate floor protector:
a. Use formulas in step 1 above to calculate R-value of proposed material(s).
b. For multiple layers, add R-values of each layer to determine overall R-value.
3. If the overall R-value of the floor protector system is equal to or greater than the floor protector
specifications given, the alternate is acceptable.
Definitions:
Thermal conductance (C) = BTU =W
(hr)(ft2)(°F) (m2)(°K)
Thermal conductivity (k) = (Btu)(inch) =W =Btu
(hr)(ft2)(°F) (m)(°K) (hr)(ft)(°F)
Thermal resistance (R) = (ft2)(hr)(°F) = (m2)(°K)
Btu W
Example:
The specs of floor protector material should be 3/4-inch thick material with a k-factor of 0.84.
The proposed alternative material is 4” brick with a C-factor of 1.25 over 1/8-inch mineral board
with a k-factor of 0.29.
Step 1: Convert specs to R-value.
R = 1/k x T = 1/0.84 x 0.75 = 0.893 System must have a R-value of 0.893 = Rspecs
Step 2: Calculate R-value of individual components
4” Brick with C-factor = 1.25. R = 1/C = 1/1.25 = 0.80 = Rbrick
1/8-inch (0.125”) mineral board with k-factor = 0.29. R = 1/0.29 x 0.125 = 0.431 = Rmin.brd.
Step 3: Add R-values of components to get total R-value of system
Rbrick + Rmin.brd = 0.80 + 0.431 = 1.231 = Rsystem
Step 4: Compare Rsystem to Rspecs
Rsystem = 1.231 is larger than Rspecs of 0.893. System R-value exceeds the required
specifications and therefore is an acceptable alternative.

VGZ-010 / 20110513.1 VG820E HEARTWOOD™ / Page 15
A. Brick Masonry
Minimum 3.5˝/ 89mm thick brick masonry all framed
into combustible wall with a minimum of 12˝/305mm
brick separation from clay liner to combustibles. The
fireclay liner shall run from outer surface of brick wall
to, but not beyond, the inner surface of chimney flue
liner and shall be firmly cemented in place.
B. Insulated Sleeve
Solid-insulated, listed factory-built chimney length of
the same inside diameter as the chimney connector and
having 1˝/25.4mm or more of insulation with a mini-
mum 9˝/229mm air space between the outer wall of the
chimney length and combustibles.
C. Ventilated Thimble
Sheet steel chimney connector, minimum 24 gauge in
thickness, with a ventilated thimble, minimum 24 gauge
in thickness, having two 1˝/25.4mm air channels, sepa-
rated from combustibles by a minimum of 6˝/152mm
of glass fiber insulation. Opening shall be covered, and
thimble supported with a sheet steel support, minimum
24 gauge in thickness.
D. Chimney Section Pass-through
Solid insulated, listed factory-built chimney length with
an inside diameter 2˝/51mm larger than the chimney
connector and having 1˝/25.4mm or more of insulation,
serving as a pass-through for a single wall sheet steel
chimney connector of minimum 24 gauge thickness, with
a minimum 2˝/51mm air space between the outer wall of
chimney section and combustibles. Minimum length of
chimney section shall be 12˝/305mm chimney section
spaced 1˝/25.4mm away from connector using sheet steel
support plates on both ends of chimney section. Open-
ing shall be covered, and chimney section supported on
both sides with sheet steel support securely fastened to
wall surfaces of minimum 24 gauge thickness. Fasten-
ers used to secure chimney section shall not penetrate
chimney flue liner.
CHIMNEY CONNECTOR SYSTEMS & CLEARANCES

Page 16 / VG820E HEARTWOOD™ VGZ-010 / 20110513.1
Vogelzang International Corporation
400 West 17th Street
Holland, Michigan 49423
www.vogelzang.com
Phone: [phone] Fax: [phone]
Toll Free: 1-800-222-6950
COMPANY TESTIMONY:
“FOR GOD SO LOVED THE WORLD THAT HE GAVE HIS ONLY BEGOTTEN SON, THAT WHOEVER
BELIEVES IN HIM SHALL NOT PERISH BUT HAVE ETERNAL LIFE”
JOHN 3:16
MADE IN CHINA
This Vogelzang heating appliance is safe when installed properly and will provide you with years of
service. However, always exercise good judgement when you are using this stove. You are dealing with
FIRE! Fire is inherently dangerous and must be treated with respect. Stay warm and in good health!
Respectfully yours,
Proprietor
Optional F-1 Blower for
Vogelzang Heat Circulator Stove Models
VG820E and VG810CL
For more even heat distribution, the
Vogelzang Heat Circulator blower draws
heat from around the firebox and blows
it under the stove unit into the room. Attaches
easily to existing panels on Vogelzang stove
models VG820E and VG810CL. Switch/
thermostat unit may be mounted in different
positions for various comfort levels. Prewired,
after mounting simply plug into standard
110 volt house wiring. Three-position switch
allows manual or thermostatic control.