Vogelzang International VG820E User manual

5
REPAIR PARTS LIST - MODEL VG820E
AUTOMATIC WOOD BURNING CIRCULATOR
INTERIOR
16
IMPORTANT
*Size the chimney to the ue outlet on the
stove. (6" outlet = 6" I.D. chimney)
*Avoid using elbows except as necessary
(they reduce dra).
*Make sure all horizontal runs of connec-
tor pipe go up hill (1/4" elevation for each
horizontal foot).
CHIMNEY CONNECTION
DO NOT CONNECT THIS UNIT TO A
CHIMNEY FLUE SERVING ANOTHER
APPLIANCE.
Two basic types of chimneys are approved
forusewithsolid fuel: Factory-builtandma-
sonry. Factory-built chimney must comply
with UL103HT standard.
Donotexpect yourstoveorfurnaceto create
dra.Drais nota functionofthe appliance.
Dra is purely a function of the chimney.
Modern stoves and furnaces are much more
air-tight and ecient than those of the
past and, therefore require greater dra. A
minimum of .05, measured in water column
(gaugestomeasurechimney draarereadily
available at stove shops and are economical
to purchase or rent) is required for proper
draing to prevent back-pung, smoke
spillage, and to maximize performance.
Chimneys perform two functions - one of
which is apparent: e chimney provides
a means for exhausting smoke and ue
gases resulting from combustion of the fuel.
Secondarily, though, the chimney provides
Key Part No. Description Qty.
1 67859 Weldment, Base 1
2 22030 Shield, Second Heat (Included w/ 67859) 1
3 22110 Shield, Heat (Included w/ 67859) 1
4 68619 Assy., Heat Jacket 1
5 88032 Gasket, Flue Collar 1
6 40246 Collar, Flue 1
7 22090 Curtain, Smoke 1
8 22171 Clip, Smoke Curtain 2
9 40075 Frame, Draft Damper 1
10 23476 Damper, Draft Control 1
11 25550 Pin, Draft Damper 1
12 83890 Clip, Push 1
13 40100 Liner, Front/Back 3
14 40076 Fire, Grate 2
15 40132 Retainer, Brick 2
16 89066 Firebrick (4.5” x 9” x 1.25”) 10
17 891940 Assy., Feed Door (Complete) 1
- 40199 Feed Door - Casting Only -
18 88033 Rope Gasket, 3/8” 3.75 ft.
19 891941 Assy., Ash Door (Complete) 1
- 40289 Ash Door - Casting Only -
20 88033 Rope Gasket, 3/8” 2.42 ft.
21 83872 Pin, Door - Short 1
22 23441 Pin, Door - Long 1
23 83102 Bolt, 1/4-20 x 1.25” CS, Slotted Hd. 2
24 40056 Wheel, Draft 2
25 83415 Nut, 1/4-20 Jam 2
26 25201 Shield, Flame 2
27 83250 Kep Nut, 1/4-20 4
28 40509 Handle, Door 2
29 89523 Handle, Drop Wood 1
30 22434 Latch, Door (2-Step) 1
31 83045 Washer, Flat 2
32 83273 Washer, Spacer 1
33 22108 Latch, Door (Door Stop) 1
34 23474 Liner, Top 1
35 67444 Ash Pan 1
FIG. 6
Cathedral Ceiling - Chimney
Cap Mandatory
PIPE
FLOOR PROTECTOR
REFER TO CHIMNEY
MANUFACTURERS PARTS
AND INSTRUCTIONS
2 FT MIN.
10 FT. 3 FT.
MIN.
BAROMETRIC
DRAFT CONTROL
(OPTIONAL)
11 FT. MIN.
CHIMNEY CAP MANDATORY
DAMPER
FIG. 5
PIPE
FLOOR PROTECTOR
REFER TO CHIMNEY
MANUFACTURERS PARTS
AND INSTRUCTIONS
2 FT MIN.
10 FT. 3 FT.
MIN.
BAROMETRIC
DRAFT CONTROL
(OPTIONAL)
11 FT. MIN.
CHIMNEY CAP MANDATORY
DAMPER
"Dra" which allows oxygen to be continu-
ously introduced into the appliance, so that
proper combustionis possible.AsofApril 1,
1987,allheatersandfurnacesmanufactured
by United States Stove Company should be
installed using a factory built chimney that
meetsthe "Type HT"requirementofUL 103
(when a factory - built chimney is used).
Your smoke pipe should be assembled in
such a way that the male section (crimped
end) of the pipe faces down. Attach each
of the sections to one another with three
equidistant metal screws. Seal with furnace
cement.
IN ORDER TO MAINTAIN WARRANTY, COMPONENTS MUST
BE REPLACED USING ORIGINAL MANUFACTURERS PARTS
PURCHASED THROUGH YOUR DEALER OR DIRECTLY
FROM THE APPLIANCE MANUFACTURER.
USE OF THIRD PARTY COMPONENTS WILL VOID THE
WARRANTY.

FLOOR PROTECTOR
2 FT MIN.
10 FT.
MINIMUM 3 FT.
MIN.
APPROVED COWL
6"
MIN.
6" MIN.
APPROVED
THIMBLE
60" MIN.
DAMPER
BAROMETRIC DRAFT
CONTROL
THIMBLE
COLLAR
PIPE
NON-COMBUSTIBLE
WALL
FLOOR PROTECTOR CLASS A UL 103HT
CHIMNEY KIT INCLUDING
WALL THIMBLE.
BAROMETRIC
DRAFT CONTROL
(OPTIONAL)
DAMPER
6 15
FIG. 6B - Typical Masonry Chimney Installation
FIG. 6A - ru-e-Wall Installation
REPAIR PARTS
AUTOMATIC WOOD BURNING CIRCULATOR HEATER
MODEL NUMBER VG820E
EXTERIOR REPAIR PARTS LIST
KEY NO. PART NO. DESCRIPTION QTY.
1 89635 Cabinet Door Knob 1
2 83005 Screw (10-24 x 1/2) FL 1
3 83033 Screw (8-32 x 1/4) PH,TR,HD,Z 1
4 83093 Spring Latch 1
5 83244 Kep Nut (10-24) 1
6 67968BR Cabinet Door Frame 1
7 69271 Thermostat Linkage 1
8 852091 Control Panel Plate 1
9 89687 Thermostat Knob 1
10 67725GO Cabinet Front Assembly 1
11 67967BR Cabinet Left Side 1
12 21593 Hinge Support 1
13 83833 Hinge Clip 1
14 67966BR Cabinet Top 1
15 67743 Thermostat Assembly 1
16 21063 Back Brace 2
17 69557BR Cabinet Back 1
18 89065 Door Hinge 4
19 67969BR Cabinet Door 1
20 23477 Top Thermostat Shield 1
21 83554 3/16 Aluminum Rivet 2
IN ORDER TO MAINTAIN WARRANTY, COMPONENTS MUST
BE REPLACED USING ORIGINAL MANUFACTURERS PARTS
PURCHASED THROUGH YOUR DEALER OR DIRECTLY FROM
THE APPLIANCE MANUFACTURER.
USE OF THIRD PARTY COMPONENTS WILL VOID THE
WARRANTY.

14 7
CAUTION:
NOT ALL FIREPLACES
ARE SUITABLE FOR
INSTALLATION OF A WOOD
HEATER.
Manypeoplemaywishto convert anexisting
replace to heater use. Usually, safe con-
nection of stovepipe to a masonry chimney
requires more eort than connection to a
prefabricated chimney. e replace must
be closed and sealed at the damper in the
ue. Good sealants are high temperature
caulking, ceramicwool,andfurnace cement.
Always remember to inspect the masonry
chimney and replace. If necessary, clean
the ue and smoke shelf before beginning
your installation. Install the heater into the
chimneysothatthesystemcanbedismantled
for cleaning and inspection.
Before deciding to convert your replace or
existing chimney, keep in mind that older
replaces and their chimneys are unsafe.
ey must be structurally sound, and the
ue liner must be in good condition. Do
not use a chimney if it is unlined (should
have a tile clay liner to protect brickwork),
haveitrelinedprofessionally. Clearancesto
combustibles are explained in the previous
section on masonry chimneys. If you have
any questions regarding the condition of
the chimney, consult a qualied engineer,
competentmason,certiedChimneySweep,
or knowledgeable inspector.
Many prefabricated replaces fall into the
"zero-clearance replace" category. is is
a factory metal replace with multi-layered
construction. It is designed to provide
enough insulation and/or air cooling so that
the base, back and sides can be safely placed
in close contact with combustible oors
and walls. Although many prefabricated
replaces have been tested by nationally
recognized organizations for use as re-
places, they have not been tested to accept
heaters. In fact, their use as such may void
the manufacturer's warranty.
Steel-lined replaces, on the other hand,
can be used with heaters. ese units use a
1/4-inch re box liner and an air chamber
in connection with 8 inches of masonry to
meet code. ey contain all the essential
parts of a replace, rebox, damper, throat,
smoke shelf, and smoke chamber. Many of
them look exactly like a masonry replace
and must be checked closely for above re-
quirements before installing a coal heater
into them.
Another method frequently used by some
people is to vent the heater directly into the
replace. is does not meet code since the
heater is being vented into another appli-
ance - the replace. is method should not
be attempted because combustion products
will deposit and build up in the rebox or
replace. Be certain not to install a hazard
in you house. You will void your warranty
with this installation.
VENTING INTO A FIREPLACE
(Not recommended)
Heartwood
654
21
22
7 8
27
26
24 23
28
29
30
31
27
32
33
31
27
28
17 18
1920
15
16
13
14
13
3
2
1
11
912
10
35
25
34
REPAIR PARTS - EXTERIOR
REPAIR PARTS - INTERIOR