Volt VPL-1017 User manual

VOLT®Low Voltage Landscape Lighting
VOLT® Scroll or Leaf Tower Bollard Light
VPL-1017 and VPL-1018
INSTALLATION INSTRUCTIONS
Specications and product details subject to change without notice.
© Copyright 2019, VOLT® Lighting, Lutz FL USA 33549 • All rights reserved.
[email protected] • 813.978.3700
Help Hotline:
1-813-978-3700 • Mon-Fri 8am-8pm • Sat-Sun 10am - 6pm (EST)
- 1 -

[email protected] • 813.978.3700
VOLT®Scroll and Leaf Tower Bollard Light
VPL-1017 and VPL-1018
Important: Please Read Before Installation
INSTALLATION INSTRUCTIONS
This xture is intended for installation in accordance with local codes and
the National Electric Code (NEC). Failure to adhere to these codes and
instructions may result in serious injury, property damage and void the
warranty.
These instructions do not intend to cover all variations in installation,
operation maintenance or mounting situations.
1. Make sure that the power is turned OFF before installing or servicing
this xture.
2. Warning: this xture is not intended to be installed within 10 feet [3
meters] of a pool, spa or fountain.
3. This xture is intended to be used only with a power supply
(transformer) rated maximum of 50 watts (25 AMPS) at 12 volts.
4. Underground Low Energy Cable must not be buried over 6” (15.2 cm)
in order to connect to the main low voltage cable.
5. Wiring connections must be made with wire connectors that are
suitable for outdoor use.
6. Position the wire connector so that it is located within 6 inches (15.2
cm) from a building structure, a luminaire, or tting.
!
Important Safety Instructions
LIGHTED LAMP IS HOT!
WARNING – TO REDUCE THE RISK OF FIRE OR INJURY TO PERSONS.
1. Turn o/unplug and allow to cool before reducing lamp.
2. Lamp gets HOT quickly!
3. Do not touch the hot lens, guard or cowl.
4. Keep lamp away from materials that may burn.
5. Do not touch lamp at any time.
6. Use a soft cloth.
7. Oil from skin may damage lamp.
8. Do not operate the xture with a damaged or missing lens or shield.
!
- 2 -
Package Contents
Product Dimensions
A. (1) Fixture
B. (2) Stakes
C. (2) Threaded Couplers (attaches
stake and xture)
8” x 8” 8” x 8”
6.5” x 6.5”
VPL1017-26 Pictured
VPL1017-42 Pictured
6.5” x 6.5”
3” 3”
26”
42”
- 3 -
www.voltlighting.com

www.voltlighting.com
INSTALLATION INSTRUCTIONS
Install Stakes to Fixture
1
Lay down the xture body on a at surface. Screw the couplers into the
mounting holes on the bottom of the xture body then thread the stakes
onto the couplers. Hand tighten to secure the stakes onto the xture
body.
Fixture Body
Fixture Body
Stake
Coupler
[email protected] • 813.978.3700
- 4 -
Install Stakes to Ground
2
- 5 -
www.voltlighting.com
Determine the desired location for
the xture. Clear away an area in
the ground and lay the luminaire
pigtail into the wireway slot. Insert
stakes into the ground until ange
of stakes are ush to grade.
NOTE: If the ground is hard and
stakes are dicult to install, make
a crosscut in the ground using a at
shovel.
Stake
Soil
Ground
Pigtail
Wire Connection
3
Strip both leads from the luminaire pigtail. Using two wire connectors
(not provided), connect the leads from the xture body to the main
supply cable leads.
Pigtail
Main Supply Cable
Wire Connectors
VOLT®Scroll and Leaf Tower Bollard Light
VPL-1017 and VPL-1018

[email protected] • 813.978.3700
- 6 - - 7 -
INSTALLATION INSTRUCTIONS
VOLT®Scroll and Leaf Tower Bollard Light
VPL-1017 and VPL-1018
www.voltlighting.com

- 8 -
IS-VPL-1017-1018-Ver6.pdf
Specications and product details subject to change without notice.
© Copyright 2019, VOLT® Lighting, Lutz FL USA 33549 • All rights
reserved. [email protected] • 813.978.3700
www.voltlighting.com
Help Hotline:
1-813-978-3700 • Mon-Fri 8am-8pm • Sat-Sun 10am - 6pm (EST)