Volt VAL-2012-BBK User manual

VOLT®Low Voltage Landscape Lighting
VOLT®Brass Lanai Light
VAL-2012-BBK
INSTALLATION INSTRUCTIONS
Specications and product details subject to change without notice.
© Copyright 2022, VOLT® Lighting, Lutz FL USA 33549 • All rights
reserved. [email protected] • 813.978.3700
- 1 -
Help Hotline:
1-813-978-3700 • Mon-Fri 8am-8pm • Sat-Sun 10am - 6pm

VOLT®Brass Lanai Light
VAL-2012-BBK
INSTALLATION INSTRUCTIONS
www.voltlighting.com
Important: Please Read Before Installation
Important Safety Instructions
!
!
- 2 -
This luminaire is intended for installation in accordance with local
codes and the National Electric Code (NEC). Failure to adhere to
these codes and instructions may result in serious injury, property
damage and void the warranty.
These instructions do not intend to cover all variations in
installation, operation maintenance or mounting situation.
1. Make sure the power is turned OFF before installing or servicing this
luminaire.
2. WARNING: risk of electrical shock. Install all luminaires 10 feet (3.05M)
or more from pool, spa or fountain.
3. This luminaire is intended to be used at 12V/AC.
4. Wiring connections must be made with UL listed wire connectors that
are suitable for outdoor use.
5. Position the low voltage wire and UL listed wire connector so that
it is located within 6 inches (15.2 cm) from a building structure, a
luminaire or tting.
6. The main low voltage cable is intended for shallow burial - less than 6
inches (152 mm).
INSTRUCTIONS PERTAINING TO A RISK OF FIRE, OR INJURY TO PERSONS
Lighted lamp is HOT!
WARNING – TO REDUCE THE RISK OF FIRE OR INJURY TO PERSONS.
1. Lamp gets HOT quickly!
2. Do not touch the hot lens, guard or enclosure.
3. Keep lamp away from materials that may burn.
4. Do not touch lamp at any time. Use a soft cloth. Oil from skin may
damage lamp.
5. Do not operate the luminaire tting with a missing or damaged shield.
SAVE THESE INSTRUCTIONS

[email protected] • 813.978.3700
Package Contents
Parts Required (Sold Separately)
A. (1) MR11 Bulb
Product Dimensions
- 3 -
A. (1) Fixture
B. (3) Screws
C. (3) Wall Anchors
1.62”
1.85”
1.62”
10”
3.27”

INSTALLATION INSTRUCTIONS
www.voltlighting.com
- 4 -
1
2
VOLT®Brass Lanai Light
VAL-2012-BBK
Remove Lens from Fixture
Remove the lens from the
xture body by rotating the
lens counter-clockwise.
Lens
Fixture Body
Install Fixture Body
Place the xture wires through
the cut out of the backplate.
Attach the backplate onto the
desired location and mark the
three points on the wall surface.
Drill a hole using the marks and
insert the wall anchor.
Place the backplate onto
the wall surface and secure
by threading screws into
wall anchors. Tighten with a
screwdriver.
NOTE: This xture can be
oriented upwards or downwards.
Fixture Body
Wall Anchor
Backplate
WALL
Screw
Mark
Cut out
Fixture Wires

4
[email protected] • 813.978.3700
- 5 -
3
Install MR11 Bulb
Socket
Insert the MR11 bulb with
the correct wattage and type
marked on the xture label.
CAUTION: Do not exceed
maximum wattage marked on
luminaire label.
MR11 Bulb
Install Lens
Lens
Fixture Body
Install the lens to the xture
body by rotating clockwise.

INSTALLATION INSTRUCTIONS
www.voltlighting.com
- 6 -
5
VOLT®Brass Lanai Light
VAL-2012-BBK
Wire Connections
Strip both leads from the xture wires. Using two UL listed wire
connectors (sold separately), connect the leads from the xture
wires to the main supply cable leads.
Main Supply Cable
Fixture Wires
Wire Connectors

[email protected] • 813.978.3700
- 7 -

IS-VAL-2012-BBK-ver1.pdf
Specications and product details subject to change without notice.
© Copyright 2022, VOLT® Lighting, Lutz FL USA 33549 • All rights
reserved. [email protected] • 813.978.3700
www.voltlighting.com
Help Hotline:
1-813-978-3700 • Mon-Fri 8am-8pm • Sat-Sun 10am - 6pm
- 8 -