PROGRAMMING
89
(*) summer/winter time change
If the automatic update of summer time is active (on), the change occurs
according to the set geographical zone:
Zone Start DST (+1h) End DST (-1h)
01 Australia First Sunday, October First Sunday, April
02 New Zealand Last Sunday, September First Sunday, April
Note: time change is fixed for all zones at 2:00am for the start
of DST and at 3:00am for the end of DST.
3s
Year setting Month setting Day setting
Geographical
zone setting
Operation setting**
Time setting Minutes setting Summer/winter
time change*
ADVANCED PROGRAMMING
Programming consists of 7 different
programs, one for each day of the
week.
The timer splits the 24-hour day up into 48
time-blocks, with each block 30 minutes long.
When a block is ON, the relay output is on.
Before programming, all 48 blocks are OFF.
The timer can be set to turn any combination
of the 30-minute blocks ON. Midday
Midnight
6am6pm
30-minute
block OFF
30-minute
block ON
Setting blocks to ON
Use a pen or similar to press the programming buttons.
Press the PRG button (short press) to enter programming mode. The
day indicator will flash.
Scroll through days by pressing (Monday = 1, Tuesday = 2, etc.).
Select the day required by pressing PRG. The time will indicate 00:00
(midnight).
Press the PRG button to incrementally move through the 30-minute
blocks, starting at midnight. The time will increment by 30 minutes each
time the PRG button is pressed.
If a block is required to be ON, press the button and then the PRG
button. If it needs to be OFF, just press the button PRG button again to
move to the next block. Blocks set to ON will be shown as black (see the
diagram above).
When all the required blocks are set to ON, press the PRG button for 3
seconds to return to the day selection screen.
Program other days as required.
When programming is finished, press the PRG button for 3 seconds to
return to the main screen.
1.
2.
3.
4.
5.
6.
7.
8.
Changing Blocks from ON to OFF
In programming mode, use the PRG button to move to the block required to
be changed. The block will flash.
When the block is flashing, press the button. The block will change from
ON to OFF.
1.
2.
3.
A block currently set to ON can be set to OFF as follows
10 Battery Replacement
1.
2.
3.
4.
Copy function
Choice of the
day to copy
The copy function allows you to copy programming from
one day to another.
Follow steps 1 to 3 of ‘Setting blocks to ON’ (above) to
go to the day required to be copied
Press the and buttons at the same time. ‘COPY’
appears on the display and the day flashes
Choose which day to copy to with the and buttons
Confirm with the PRG button
To copy an existing program in another day:
Display date and programs
From the main page, successively press the button to scroll through the
programs set for each day and the set date (day and month).
Programming mode will exit if no buttons are pressed within the time-out period
(40 seconds if the device is mains powered, 10 seconds if powered by the
backup battery). Any modifications are still saved.
Note
Before you access the battery compartment, disconnect mains.
So that date and time is not lost, replace the battery within one minute of
removing it.
Only use a CR-1632 type battery
Note
When the backup battery is low the
device displays and the
battery should be replaced as soon as
possible.
Operating setting
Weekly operation allows a different program on each day of the week
Daily operation runs the same program every day
The Operation setting allows the time to be changed from weekly (7)
operation (default) to daily (1) operation
(**)
From the main screen, press the key
for >3 seconds
This allows you to change:
- geographical zone of installation
- date and time,
- Summer/winter time automatic update
- Operating mode (daily or weekly)
