Voxx Prestige PE2RELCDZ User manual

12019 Voxx Electronics Corporation. All rights reserved.
Owner’s Guide
For Models:
PE2RELCDZ
IMPORTANT NOTE: The operation of the Security and Convenience System as described in this manual is
applicable to most vehicles. However, due to the conguration of some vehicles, some functions AND/OR
SAFETY PRECAUTIONS may not apply. Please see your installing dealer for more information.
FLRSBA
RF Upgrade Kit

2FLRSBA_PE2RELCDZ Owners REV 0
Table of Contents
Using Your Remote Control.................................................................... 3
Arming the Security System .............................................................. 3
Disarming the Security System ......................................................... 3
Two Stage Door Unlock (optional)..................................................... 3
Activating Trunk Release (optional)................................................... 3
Activating AUX Output (optional)....................................................... 3
Using the Personal Protection Alarm................................................. 3
Programmed Transmitter Notication................................................ 4
Valet Mode ........................................................................................ 4
Manually Overriding the Security System ......................................... 4
Stand Alone Valet Override ............................................................... 4
Custom Code Valet Override............................................................. 5
Using Your Remote Vehicle Starter ....................................................... 6
Remote Starting Your Vehicle............................................................ 6
Remote Start Shutdown .................................................................... 6
Entering Your Vehicle while it is Running via Remote Start .............. 6
Preheating or Precooling the Vehicle’s Interior ................................. 6
Remote Start Safety Features........................................................... 6
Using the “Quick-Stop” Feature......................................................... 7
Operating the Daily Start Timer ......................................................... 7
Temperature Start Mode.................................................................... 7
Operating the 2 / 4 Hour Start Up Timer Mode.................................. 8
Status LED, Light Flashes and Siren/Horn Indications ....................... 9
Additional 2-Way LCD Remote Control Functions............................. 10
Programming Remote Controls ........................................................... 12
Replacing Remote Control Batteries................................................... 12
Warranty Information ............................................................................ 13

32019 Voxx Electronics Corporation. All rights reserved.
Arming the Security System
To arm the system, exit the vehicle, close all doors, then press the button. The
parking lights will ash one (1) time, indicating the system is armed, has locked the
doors (if equipped and connected) and activated the starter disable feature. The LED
status indicator will blink steadily, once per second.
NOTE: The system is equipped with a feature called Silent Choice. If enabled, the
system requires a second press of the button to activate an audible arming response
from the vehicle.
*Throughout this manual, ‘press’ refers to pressing for less than 1 second; ‘press and hold’ refers to pressing for more
than 3 seconds.
Using Your Remote Control
Two Stage Door Unlock (Optional)
If this feature is enabled on your system, pressing the button one (1) time will unlock
only the driver’s door. Press again within three (3) seconds to unlock the remaining
doors.
Disarming the Security System
To disarm the system press the button. The parking lights will ash two (2) times,
indicating the system is disarmed and has unlocked the doors (if equipped and
connected).
NOTE: The system is equipped with a feature called Silent Choice. If enabled, the
system requires a second press of the button to activate an audible disarming
response from the vehicle. If your system is set up for 2 stage unlock, a third press of
unlock will activate the audible response.
Activating the Trunk Release Feature (Optional)
If this feature is enabled on your system, pressing and holding the button for three
(3) seconds will open the vehicle’s trunk or hatch.
Activating the AUX 1-4 Output (Optional)
AUX channel output is an optional feature and programming is required at the time of
installation. Please consult your dealer for more information.
Using the Personal Protection Alarm (Panic)
Press and hold the or button for three (3) seconds to activate the personal
protection alarm. During panic mode, the normal function of the transmitter buttons
will be suspended. The transmitter’s and buttons can be used to lock and unlock
the door (if the option is installed). To stop the alarm, press and hold the or button
on the transmitter again for three (3) seconds. The system will automatically stop after
thirty (30) seconds.

4FLRSBA_PE2RELCDZ Owners REV 0
Programmed Transmitter Notication
As a security precaution each time the vehicle’s ignition is turn on the status LED
light with ash the number of transmitters programmed into the system. This helps
to identify unauthorized transmitters from accessing your vehicle. If you believe an
unauthorized transmitter has been programmed to your system, contact your installing
dealer for assistance.
Manually Overriding the Security System
Your system can be disarmed without the use of the transmitter. This is necessary to
operate your vehicle if the transmitter is lost or its battery fails. To by-pass the alarm
system;
1. Open the vehicle door. The alarm will sound.
2. Turn the ignition key to the ON position.
3. Within ten (10) seconds, press and release the valet push button switch.
The alarm system will stop sounding and enter the (by-passed) mode. You can now
start and operate the vehicle normally.
Stand Alone Valet Override (Optional)
Your system can be disarmed without the use of the transmitter or valet button. This
is necessary, since you will need the ability to operate your vehicle if the transmitter
is lost or its battery fails. To by-pass the alarm system;
1. Open the vehicle door. The alarm will sound.
2. Cycle the ignition key ON, OFF, ON.
3. Within ten (10) seconds, press and release the Brake pedal three (3) times.
The alarm system will stop sounding and enter the (by-passed) mode. You can now
start and operate the vehicle normally. This feature must be programmed ON by an
authorized dealer.
Note: This procedure will also activate and deactivate Valet Mode. When Valet Mode
is active the LCD remote will display LOCK or UNLOCK on the screen locking or
unlocking the doors.
Valet Mode
When valet mode is activated the status LED will light solid, and all security and
remote start functions will be disabled. To enter or exit valet mode simply follow the
steps outlined below:
1. Turn the vehicle’s ignition ON.
2. Push and hold the programming/valet button.
3. The LED will turn on solid when valet mode is active
4. Release the programming/valet button.
When Valet Mode is active the LCD remote will display LOCK or UNLOCK on the
screen locking or unlocking the doors

52019 Voxx Electronics Corporation. All rights reserved.
Custom Code Valet Override (Optional)
Unlike the default Valet Override, Custom Code Override is a user personalized
code that o󰀨ers a higher lever of security. If the user chooses to use Custom Code
Override, Feature Bank 2 ; Feature 9 must be programmed for “Custom Code”. Once
the option has been selected the code must be programmed. Once the Custom Code
is programmed it cannot be changed without rst disarming the alarm.
Custom Code Override Procedure
The Custom Code is made up of 2 numbers. Each chosen number must be between
digits 1-9. The default Custom Code is “11”. To disarm the alarm using the Custom
Code option:
1. Turn the vehicle ignition to ON.
2. Within ve (5) seconds, Press the valet button one (1) time.
3. Within ve (5) seconds, Turn the ignition OFF/ON.
4. Within ve (5) seconds, Press the valet button one (1) time.
5. Turn the vehicle ignition to OFF then ON to start the vehicle.
Custom Code Programming Procedure
In this example, the user has selected Custom Code “23”. To program a user selected
custom code:
Start with the alarm disarmed.
1. Turn the ignition to the ON position.
2. Within ten (10) seconds, press the valet button three (3) times to enter
programming.
3. Within ten (10) seconds, Cycle the ignition OFF/ON, OFF/ON, OFF/ON. The
system will beep one (1) time.
4. Within ten (10) seconds, Press the valet button two (2) times. This number will
indicate the rst digit of the chosen Custom Code.
5. Within ten (10) seconds, Cycle the ignition OFF/ON.
6. Within ten (10) seconds, Press the valet button three (3) times. This number
will indicate the second digit of the chosen Custom Code.
7. Cycle the ignition OFF.
If the Custom Code was accepted the LED will ash the rst number (2), pause, then
the second number (3). This will repeat two (2) more times to conrm the Custom
Code entry. If after fteen (15) seconds the LED does not ash please repeat steps
1-7.

6FLRSBA_PE2RELCDZ Owners REV 0
Using Your Remote Starter
Remote Starting Your Vehicle
To activate the remote start function, press and release the button two (2) times
within two (2) seconds. The system will sound, the parking lights will ash one (1)
time and the system will check the vehicle to ensure it is safe to start. If all safety
parameters are correct, the vehicle will start. The vehicle’s parking lights will turn on
(or ash depending on system settings) as a visual indication that the vehicle has
started and is running.
If your vehicle stalls or does not start, the system will pause ve (5) seconds, then try
two (2) more times to start the vehicle (a total of three (3) attempts). The system will
pause 5 seconds between each start attempt.
Remote Start Shutdown
Press and release the button two (2) times to turn the vehicle o󰀨.
Entering the Vehicle while it is Running via Remote Vehicle Start (Optional)
1. Unlock the vehicle’s doors.
2. Enter the vehicle. DO NOT PRESS THE BRAKE PEDAL!
3. Insert the key into the ignition switch and turn to the ON or RUN
position.
4. Press the brake pedal. The remote vehicle starter will disengage and
the vehicle will operate normally.
Preheating or Precooling the Vehicle’s interior
Before exiting the vehicle, set the temperature controls to the desired setting and
operation. After the system starts the vehicle, the heater or air conditioner will
activate and heat or cool the vehicle’s interior to your setting.
Remote Start Safety Features
For safety and security reasons, the system will shutdown or prevent the remote
vehicle starter from activating if any of the following occur:
• The vehicle’s hood is open.
• The brake pedal is pressed prior to turning the ignition key to the ON position.
• The engine is over-revved (tach checking only).
• Valet Mode is active. Refer to the Valet Mode section of this manual on page 5.
• Remote Start Ready Mode is not set. Manual transmission vehicle’s only.

72019 Voxx Electronics Corporation. All rights reserved.
Using the “Quick-stop” Feature
If you want to make a short stop and keep your vehicle running (to keep the interior
warm or cool), the quick-stop feature allows you to do this while keeping your vehicle
secure and your keys with you.
To engage Quick Stop:
1. Stop the vehicle and place the transmission in PARK.
2. With your foot o󰀨 the brake pedal, press and release the button two (2)
times within two (2) seconds. The parking lights will turn on to conrm quick
stop is entered.
3. Remove the keys from the ignition and exit the vehicle. Press the button to
lock the vehicle’s doors if desired.
Operating the Daily Start Timer
The system has the ability to start your vehicle based on a 24-hour countdown timer.
This feature requires a two-part activation sequence. From the remote, while in range
of the vehicle, pressing both the &
OPT
buttons together will activate the 24 hour
countdown timer (the vehicle will start 24 hours from this time). Next, when you are
nished operating the vehicle for the day, perform the following steps to complete the
process.
1. Turn the ignition ON/OFF (vehicle must be disarmed).
2. Within ten (10) seconds, while pressing the brake, press and release the
button twice.
3. The vehicle will emit two (2) chirps and ash the parking lights four (4) times.
Temperature Start Mode
The system has the ability to start the vehicle if the temperature drops below a preset
temperature threshold. Once activated, the system will only start the vehicle one time
based on the temperature setting and will be cancelled if the vehicle is started with the
key or remote started by the transmitter. Temperature is read from the module, located
below the dashboard in most instances, and the vehicle’s interior temperature may
vary from the ambient temperature.
1. The vehicle must be armed.
2. Press and release both the &
OPT
buttons together.
Note: This feature is defaulted OFF and must be set in option programming.

8FLRSBA_PE2RELCDZ Owners REV 0
Operating the 2 / 4 Hour Start Up Timer Mode
The system has the ability to start the vehicle every two (2) or four (4) hours for a
forty-eight (48) hour period. This feature is especially useful in cold climates where
the only means to keep the engine and engine uids warm is to periodically start the
engine. The default setting is four (4) hours.
WARNING!
Be certain that the vehicle is outdoors before using this or any remote starting
device. A running engine produces dangerous carbon monoxide fumes which can be
harmful or fatal if prolonged exposure occurs. DO NOT remote start the vehicle if it is
garaged.
To congure 2 / 4 hour start timer mode:
1. Press and hold the valet button.
2. Cycle the vehicle’s Ignition ON/OFF one (1) time.
• To set for 2 Hour (default) - Press the valet button two (2) times. The
Parking lights will ash two (2) times for conrmation.
• To set for 4 Hour (default) - Press the valet button four (4) times. The
Parking lights will ash four (4) times for conrmation.
To activate the 2 / 4 hour start up timer mode:
1. Start the vehicle and let it run for more than fteen (15) seconds.
2. Cycle the vehicle’s Ignition to the OFF position.
3. Press and release the button on the remote four (4) times.
The vehicle’s parking lights will ash two (2) or four (4) times to conrm the timer
mode is activated.
To exit the 2 / 4 hour start up timer mode:
• Remote start the vehicle using the remote control.
• Start the vehicle normally using the Ignition key.

92019 Voxx Electronics Corporation. All rights reserved.
Status LED, Light Flashes, and Siren/Horn Indications
Status LED Flash Indications
LED Flashes Function
OFF Disarmed
Slow Flash Armed
Fast Flash Passive Arming Countdown
ON (Solid) Valet Mode
1 Flash / Disarmed Zone 1 Trigger, Shock Sensor
2 Flashes / Disarmed Zone 2 Trigger, Trunk / Hood
3 Flashes / Disarmed Zone 3 Trigger, Door
Siren/Horn Chirp Indications
Chirps Function
1 Arm
2 Disarm
3 Door Ajar Upon Arming
4 Disarm / Triggered
Parking Light Flash Indications
Flashes Function
1 Arm
2 Disarm
3 Disarm / Triggered
ON (Solid or Slow Flash) Remote Started

10 FLRSBA_PE2RELCDZ Owners REV 0
Additional 2-Way LCD Remote Control Functions
Additional Features of the Optional 2 Way LCD Remote Control
Parking Meter Countdown
The parking meter countdown timer has six (6) preset times, to access the preset
times and begin countdown press and hold
F
then press and release
OPT
, each
additional press of
OPT
will increase the countdown time.
Stopping LCD Trigger Melody
To stop the alarm trigger melody if the system has been triggered WITHOUT
disarming the system, press button one time only, this will send a lock command to
the vehicle at this time and the alarm will silence.
Battery Save Mode
While in POWER SAVE MODE the 2-Way LCD transmitter will NOT look for any
incoming signals from the main unit until a button is pressed. The LCD screen will
display SAVE ON to indicate that power save mode is ON. To enter power save mode
press and hold
F
then press .
Melody / Vibration Mode
To have the remote control vibrate or play a melody tone each time it receives a
response from the vehicle press and hold
F
then press and release .
Display Illumination
Press and hold the
F
button for one (1) second. The display will illuminate for ve (5)
seconds.

112019 Voxx Electronics Corporation. All rights reserved.
Adjusting the Clock and Timer Settings
The clock, alarm clock and programmable countdown timer are accessed through the
Function Menu. Press and hold
F
for 5 seconds to access the function menu, once
you have accessed the feature menu press and release
F
to scroll through each
feature and follow the steps below to adjust the settings for each. Press and hold
F
for 5 seconds to exit the menu.
Clock Hour Press to increase or
OPT
to decrease
Clock Minute Press to increase or
OPT
to decrease
Alarm Clock Hour Press to increase or
OPT
to decrease
Alarm Clock Minute Press to increase or
OPT
to decrease
Alarm Clock Alert Tone Press or
OPT
to change tone
Alarm Clock ON / OFF Press to turn ON or
OPT
to turn OFF
Countdown Timer Hour Press to increase or
OPT
to decrease
Countdown Timer Minute Press to increase or
OPT
to decrease
Shutdown Alert Tone Press or
OPT
to change tone
Countdown Timer ON / OFF Press to turn ON or
OPT
to turn OFF
Remote Start Alert Tone Press or
OPT
to change tone
LCD Remote Control ICON’s
Locked / Armed
Door Open
Hood Open
Engine Running
Valet Mode
Shock Sensor
Vibrate Mode
Unlocked / Disarmed
Alarm Clock
Transmitting
Battery Indicator
Timer Start
Time Display
Trunk Open
Alarm Notification
Remote Start Shutdown
2nd Car Mode
Shock Sensor OFF
Remote Page
Out Of Range
Power Save Mode
Temp Start
Count Down Timer
Temp Display

12 FLRSBA_PE2RELCDZ Owners REV 0
Replacing Remote Control Batteries
5 Button Remote Control - Model 185SP
The CR2032 battery inside each remote control should last approximately 1 year
under normal use. When the batteries become weak you will notice the remote control
range (the distance from the vehicle the remote control will work) deteriorate and the
small LED on the remote control will dim. To replace the remote control batteries:
1. Using a coin, disassemble the halves of the remote control.
2. Remove the old battery, observing the +/- symbols on the batteries and replace
with a new battery.
3. Reassemble the halves of the remote control.
4. Test operation of the remote control.
2 Way LCD Remote Control - Model 18RELCD
The battery inside the 2-way LCD remote control is rechargeable and should last
approximately 30-60 days under normal use. When the battery becomes weak you
will notice the remote control range (the distance from the vehicle the remote control
will work) deteriorate and the battery icon on the LCD remote control will show 1 bar
or less.
To recharge the remote control.
1. On the back of the remote; Pull tab with USB symbol up and way from the back
case.
2. Rotate USB tab from right to left to slide out the remote charging port.
3. Press USB tab into place. The lock will engage.
Repeat the process above in reverse to stow the charging port.
Programming Remote Controls
To Program The Remote Controls
1. Cycle the vehicle's ignition switch to the ON position.
2. Press and release the valet button on the antenna three (3) times. The LED on
the antenna will turn on solid to indicate the system is ready for remote control
programming.
3. Press the button on the remote control. The LED on the antenna with ash
one (1) time to conrm the remote has been programmed.
4. Repeat step 2 above for each additional remote control.

132019 Voxx Electronics Corporation. All rights reserved.
LIMITED LIFETIME WARRANTY
Applies to Prestige Series Control Modules, Sirens, Sensors, and Relays.
Voxx Electronics Corporation (the Company) warrants to the original purchaser of
this product that should this product or any part thereof, (other than transmitters)
under normal use and conditions, be proven defective in material or workmanship
during the lifetime of the vehicle, in which it was originally installed from the date of
original purchase such defect(s) will be repaired or replaced with new or reconditioned
product, (at the Company’s option) without charge for parts or repair labor. A
transmitter is warranted for 12 months from the date of original purchase.
To obtain repair or replacement within the terms of this Warranty, the product is to
be delivered with proof of warranty coverage (e.g. dated bill of sale), specication of
defect(s), transportation prepaid, to an approved warranty station. This Warranty is not
transferable.
This Warranty does not cover damage to the vehicle’s electrical system or costs
incurred for removal or reinstallation of the product. This Warranty does not cover
batteries, broken LCD or OLED display screens, nor apply to any product or part
thereof which, in the opinion of the Company, has su󰀨ered or been damaged through
alteration, improper installation, mishandling, misuse, abuse, neglect, accident, or by
removal or defacement of the factory serial number/bar code label(s).
This Warranty is in lieu of all other express warranties or liabilities. ANY IMPLIED
WARRANTIES, INCLUDING ANY IMPLIED WARRANTY OF MERCHANTABILITY,
SHALL BE LIMITED TO THE DURATION OF THIS WRITTEN WARRANTY. IN
NO CASE SHALL THE COMPANY BE LIABLE FOR ANY CONSEQUENTIAL OR
INCIDENTAL DAMAGES FOR BREACH OF THIS OR ANY OTHER WARRANTY. No
person or representative is authorized to assume for the Company any liability other
than expressed herein in connection with the sale of this product.
The company does not warrant that this product cannot be compromised or
circumvented. THE EXTENT OF THE COMPANY’S LIABILITY UNDER THIS
WARRANTY IS LIMITED TO THE REPAIR OR REPLACEMENT PROVIDED
ABOVE AND, IN NO EVENT, SHALL THE COMPANY’S LIABILITY EXCEED THE
PURCHASE PRICE PAID BY PURCHASER FOR THE PRODUCT WITHOUT COST
OF INSTALLATION.
Some states do not allow limitations on how long an implied warranty lasts or the
exclusion or limitation of incidental or consequential damage so the above limitations
or exclusions may not apply to you. This Warranty gives you specic legal rights and
you may also have other rights which vary from state to state.
Voxx Electronics Corporation, 2351 J. Lawson Blvd., Orlando, FL 32824 / 1-800-645-4994

14 FLRSBA_PE2RELCDZ Owners REV 0
Voxx Electronics Corporation.
Customer Service 1-800-225-6074
WWW.VOXXELECTRONICS.COM
FCC COMPLIANCE
This device complies with Part 15 of the FCC rules and with RSS-210 of
Industry Canada. Operation is subject to the following two conditions:
1. This device may not cause harmful interference, and
2. This device must accept any interference received, including any interference that
may cause undesired operation.
Warning!
Changes or modications not expressly approved by the party responsible for
compliance could void the user’s authority to operate the equipment.
PATENTED: www.voxxintl.com/company/patents