Dome Light Delay / Theater Dimming
The system can be programed to delay arming after the lock button is pressed
(60 second max) for vehicles with a dome light delay or theater dimming feature.
Once programed the system will ‘learn’ the timing of the dome light delay and add 2
seconds before arming.
1. Close all doors with ignition off.
2. Using the transmitter press LOCK, UNLOCK, LOCK ,UNLOCK, LOCK ,
UNLOCK, LOCK. The LED will light solid to indicate the system has
entered DOME DELAY LEARN MODE.
3. Immediately OPEN then CLOSE the door WITHOUT disarming the
system. The system will then monitor the door trigger wire. Once the
dome light turns off, the system will then add 2 seconds and then exit
the learning mode.
4. TheLEDwillbegintoashindicatingthesystemhasexitedthe
learning mode and is now armed.
Defaulting the Dome Light Delay: Turn the ignition ON then OFF 3 times then
press and hold the valet button for 5 seconds, the system will chirp 1 time indicating
the learned delay time has been cleared.
User Selectable LED
This feature will control whether the LED is ON or OFF when the system is Armed/
Locked.ThiswillbeselectableinfeatureprogrammingORon-the-ywithoutentering
the programming feature banks.
1. Turn the ignition ON, OFF, ON, OFF.
2. Press and release the valet/programming button 3 times. The system
will respond with 1 chirp for ON or 2 chirps for OFF.
PROFESSIONAL
SERIES
Security and Remote Start
Installation Quick Reference
Guide
caSECRS
2017 Voxx Electronics Corporation. All rights reserved.
Adjusting the Shock Sensor
1. Increase sensitivity by turning the adjustment dial clockwise.
2. Decrease sensitivity by turning the adjustment dial counter clockwise.
Tach Programming
The unit will not operate unless tach is programmed or a tachless option is
turned ON.Ifanattemptismadetostartthevehicleviatheremotestartwithoutrst
programmingtach,theunitwillashtheparkinglights7timesindicatingtachhasnot
beenlearnedandstored.Ifthetachrateisnotproperlyprogrammedtothespecic
vehicle, the unit may not realize that the vehicle is running in certain instances and
re-engage the starter motor.
The Remote Start unit will learn the tach rate of most vehicle’s single coil, multiple coil
packs, or single injector. To learn tach:
1. Turn the ignition key to the ON position.
2. Press and release the valet/override button 3 times.
3. Immediately turn the ignition key OFF.
4. Press and hold the valet/override button, then start the vehicle using
the key.
5. When the unit senses the tach signal, the parking lights will begin to
ash.
6. Allow the vehicle to settle to a normal idle speed.
7. Release the valet/program push-button switch. The parking lights will
turn on for 2 seconds and 1 long chip will indicate that the learned
tach signal is stored and the unit has exited tach learn mode.
NOTE: If the unit fails to learn tach rate due to an improper tach connection or a
poortachsource,theparkinglightswillnotash.Tocorrectthissituation,locateand
connect the PURPLE/WHITE wire to the proper tach signal, and then repeat the tach
learn routine.
Smart Tachless Mode
Smart Tachless Mode is available only if a tach signal has never been learned to the
system and when activated will automatically change the Tach Mode feature in option
programming to Tachless without the need to enter the feature programming mode.
1. Activatetheremotestart.Theparkinglightsshouldbeginashing7
times indicating no tach signal has been learned.
2. Withinthe7ashtimeperiod,pressandholdthe button.
3. The system will chirp 1 time indicating the system is now in tachless
mode.
Chirp Delete - User Accessible
System ARM/DISARM chirps can be toggled ON or OFF without entering the
programming feature banks.
1. Turn the ignition ON then OFF.
2. Press and release the valet/programming button 3 times. The system
will respond with 1 chirp for ON or 2 chirps for OFF.
RED
BATTERY 12V ( + )
BLACK
GROUND WHEN ARMED ( - )
BLUE FULL TRIGGER ( - )
GREEN WARN AWAY TRIGGER ( - )
SHOCK SENSOR & HARNESS
Replacement Part
#4700023
ORANGE 86 - ARMED OUTPUT ( - )
RED 85 - IGNITION ( + )
BLACK 87A - STARTER OUTPUT - MOTOR SIDE
WHITE / BLACK 30 - STARTER INPUT - KEY SIDE
OPEN 87 - OPEN
STARTER INTERUPT RELAY & HARNESS
86 85
30
87
87a
Replacement Part
#1024405
DBI PORT
SHOCK SENSOR PORT
TELEMATICS PORT
BLUE/BLACK START STATUS / ACTIVE OUTPUT ( - )
PURPLE/WHITE TACH INPUT
GRAY/RED PARKING BRAKE INPUT ( - )
GREEN DOOR TRIGGER INPUT ( - )
BLUE/WHITE INSTANT TRIGGER INPUT ( - )
WHITE/BLUE EXTERNAL START INPUT ( - )
PURPLE DOOR TRIGGER INPUT ( + )
BROWN/RED BRAKE INPUT ( + )
GRAY HOOD INPUT ( - )
PINK/BLACK AUX 5 OUTPUT ( - )
GRAY/BLACK AUX 3 OUTPUT ( - )
ORANGE GROUND WHEN ARMED ( - )
VIOLET/BLACK AUX 1 OUTPUT ( - )
RED/WHITE TRUNK RELEASE OUTPUT ( - )
BROWN/BLACK HORN OUTPUT ( - )
LT GREEN/BLACK FACTORY DISARM / PULSE BEFORE START ( - )
LT BLUE FACTORY ARM / PULSE AFTER START ( - )
GREEN/WHITE PULSE AFTER SHUTDOWN ( - )
BLACK/YELLOW PULSE DURING CRANK ( - )
BLUE/GREEN FACTORY DISARM 2 / 2ND UNLOCK
ORANGE/BLACK AUX 4 OUTPUT ( - )
WHITE/BLACK AUX 2 OUTPUT ( - )
#4120389
WHITE/RED PARKING LIGHT INPUT
WHITE PARKING LIGHT OUTPUT
BLACK GROUND
BROWN SIREN OUTPUT ( + )
#4120145
BLUE UNLOCK ( - )
OPEN
GREEN LOCK ( - )
#1031423
CASECRS
# 4360698
FLCART PROGRAMMING PORT
FLCART PORT
FLCART HARNESS PORT
PINK IGNITION 1 ( + )
RED BATTERY 12V ( + )
PINK/WHITE IGNITION 2 ( + )
ORANGE ACCESSORY 1 ( + )
RED/WHITE BATTERY 12V ( + )
PURPLE STARTER OUTPUT - MOTOR SIDE ( + )
# 4120110
Replacement Part
Replacement Part
Replacement Part
Remote Start / Power Harness
(6-Pin)
Replacement Part
Replacement Part
Notification Harness
(4-Pin)
Input / Output
Harness
(22-Pin)
Door Lock Harness
(3-Pin)
ANTENNA
LED
VALET
** RF KITS SOLD SEPERATELY **
Replacement Parts
1-Way # 4180065
2-Way # 4180065
Harness (4-Pin)
# 4120291
ANTENNA PORT
P
P
P
P
P
P
P
P
P
P
P
P
P
P
P
P
P
Programming Note:
P
The default wire function settings are listed next
to the wire color. Wires shown with can be
programmed to perform different functions.
Refer to the Feature Programming section to
change the default setting.
P
