VTech Baby 4-In-1 Alphabet Train Assembly Instructions

4-In-1 Alphabet Train
91-004017-001 UK
Parent’s Guide

3
3
3
INTRODUCTION
Are you ready to get rolling? Let’s chug along into learning fun with
the 4-In-1 Alphabet Train by VTech®!
This alphabet train is great for sit-down play, as well as being a
walker, pull-along wagon and ride on. Train includes 13 double-sided
letter blocks and a magic tunnel to load the blocks into the wagon.
You can also stack the blocks on the inside of the wagon and slide
the blocks down! Also features a removable activity panel, number
pad, light up piano keys, turning book and manipulative gears.
Pointer
Block Chute
Recognition Port
Number Buttons
Travel Book
Horn Button
Volume Switch
Learning Blocks
On/Off/Mode
Switch
Joystick
Electronic
Activity Panel
Release Tabs

4
4
4
INCLUDED IN THE PACKAGE
Handle
Train Engine
Bead Rail
4 Engine Wheel
Axle Covers
4 Engine Wheels
Hinge
Pull Cart Seat Pull Cart Base 2 Sets of Pull Cart
Wheels with Axles
2 Pull Cart
Back Supports
Pull Cart
Front Support
Joystick
• 4-In-1 Alphabet Train

5
5
5
WARNING
All packing materials such as tape, plastic sheets, packaging locks,
removable tags, cable ties, cords and packaging screws are not part
of this toy and should be discarded for your child’s safety.
NOTE
Please keep this Parent’s Guide as it contains important information.
NOTE
Please cut and discard the cord before
playing with the unit. The cord is not part
of the product and should be discarded
for your child’s safety.
2 Label Sheets
• Parent’sGuide
13 Double-Sided
Learning Blocks
Electronic
Activity Panel

6
6
6
GETTING STARTED
BATTERY REMOVAL AND INSTALLATION
1. Make sure the unit is turned OFF.
2. Find the battery cover on the back
of the electronic activity panel. Use
a screwdriver to loosen the screw
and then open the battery cover.
3. If used batteries are present,
remove these batteries from the unit
by pulling up on one end of each
battery.
4. Install 3 new AA batteries following
the diagram inside the battery box.
(For best performance, alkaline
batteries or fully charged Ni-
MH rechargeable batteries are
recommended).
5. Replace the battery cover and
tighten the screw to secure.
WARNING:
Adult assembly required for battery installation.
Keep batteries out of reach of children.
IMPORTANT: BATTERY INFORMATION
• Insertbatterieswiththecorrectpolarity(+and-).
• Donotmixoldandnewbatteries.
• Donotmixalkaline,standard(carbon-zinc)orrechargeable
batteries.
• Onlybatteriesofthesameorequivalenttypeasrecommended
are to be used.
• Donotshort-circuitthesupplyterminals.

7
7
7
• Removebatteriesduringlongperiodsofnon-use.
• Removeexhaustedbatteriesfromthetoy.
• Disposeofbatteriessafely.Donotdisposeofbatteriesinfire.
RECHARGEABLE BATTERIES
• Removerechargeablebatteriesfromthetoybeforecharging.
• Rechargeablebatteriesareonlytobechargedunderadult
supervision.
• Donotchargenon-rechargeablebatteries.
Disposal of batteries and product
The crossed-out wheelie bin symbols on products and
batteries, or on their respective packaging, indicates they
must not be disposed of in domestic waste as they contain
substances that can be damaging to the environment and
human health.
The chemical symbols Hg, Cd or Pb, where marked,
indicate that the battery contains more than the specied
value of mercury (Hg), cadmium (Cd) or lead (Pb) set out
in the Batteries and Accumulators Regulation.
The solid bar indicates that the product was placed on the
market after 13th August, 2005.
Help protect the environment by disposing of your product
or batteries responsibly.
VTech®cares for the planet.
Care for the environment and give your toy a second life by
disposing of it at a small electricals collection point so all its
materials can be recycled.
In the UK:
Visit www.recyclenow.com to see a list of collection points near you.
In Australia & New Zealand:
Check with you local council for kerbside collections.

8
8
8
LABEL APPLICATION
Please securely stick the labels to the train engine as indicated below:
6
7
7 9 11
8
810 12
5
4
2
3
1
10
11
9
12

9
9
9
ASSEMBLY INSTRUCTIONS
With the 4-In-1 Alphabet Train, safety comes first.To ensure your
child’s safety, adult assembly is required.
1. Insert the Joystick into the Electronic
Activity Panel. Push down on the
Joystick until you hear it click into
place. Once you have installed the
Joystick, it cannot be removed.
2. Insert the Bead Rail into the side of
the Train Engine. Press down on the
Bead Rail until you hear it click into
place. Once you have installed the
Bead Rail, it cannot be removed.
3. Position the Handle with the curved
part of the handle facing the back of
the Train Engine. Insert the Handle
into the slot on the top of the Train
Engine. Push down on the Handle
until you hear it click into place. Once
you have installed the Handle, it
cannot be removed.
4. Insert the Axles into the Engine
Wheels and then insert the Axles
into the sockets on the body of the
Train Engine. Push down on the
Engine Wheels until you hear the
wheels click into place. Once you
have installed the Engine Wheels,
they cannot be removed.

10
10
10
5. Position the Hinge so that the large
hole is facing up. Insert the Hinge into
the hole on the front of the Pull Cart
until you hear it click into place. Once
you have attached the Hinge to the
Pull Cart, it cannot be removed.
6. Insert the Pull Cart Wheels with
Axles into the bottom of the Pull Cart
until you hear them click into place.
Once you have installed the Pull Cart
Wheels, they cannot be removed.
7. Attach the Pull Cart Back Support
Pieces to the sides of the Pull Cart
Seat. Insert the Pull Cart Back
Support Pieces and the Pull Cart
Front Support into the base of the
Pull Cart until you hear them click into
place. Once you have assembled the
Pull Cart, it cannot be taken apart.
8. To attach the Pull Cart to the Train
Engine, insert the Hinge into the slot
on the back of the Train Engine. You
will hear the Hinge click into position
to indicate the Pull Cart is attached
correctly.