Wagner electronics Rapid rh User manual

The Rapid RH™moisture testing system

should be a part of the overall moisture testing

program on any project where moisture-sensitive

finishes are to be applied. Owners, General

Contractors, Flooring Contractors and Installers

need to be sure the tests they per form are

accurate, repeatable, and available to all who

want to know the current moisture condition of

a slab on their projects.

The Rapid RH™is a tool that significantly

improves the project team’s abilit y to

instantly test and/or monitor the dr ying progress

of a concrete slab without adding substantial

cost to the project. The Rapid RH™enables

you to take periodic readings without having

to conduct other types of testing. The factor y-

calibrated “Smar t Sensors” using CMOS Sens™

technology insures the sensor ’s accuracy and

fast equilibration.

Drill hole to the desired depth in concrete using a rotary-hammer drill and a ¾” SDS

drill bit*. Per ASTM F2170-02 standards, drill the hole to a depth of 1¾” (44 mm),

which is approximately 40% of the depth of a 4” (100 mm) concrete oor slab

poured on grade. For proper RAPID RH™ installation, be sure to position the

drill perpendicular (90˚) to the surface being tested. It is recommended that a drill

capable of approximately 750 rpm be used with the SDS drill bits.

For other slab thicknesses and drying conditions, please consult ASTM F2170-02

to determine the proper depth of the hole.

If the drill bit becomes extremely hot from

drilling several holes in rapid succession, allow

the bit to cool before drilling more holes.

*Champion, Hilti, Milwaukee,

Bosch, DeWalt, Relton

Installation Instructions

Step 1: Drill the Hole

Use a vacuum cleaner, or dustpan and brush to sweep up the dust around the

hole. Attach the Rapid RH™ vacuum attachment to the straight extension of a

Shop-Vac vacuum cleaner hose. Insert the vacuum attachment into the hole and

vacuum the dust within.

Remove the vacuum cleaner extension from the hole and insert the special wire

bristlebrush(provided with thekit)into the hole.Turnthe brushseveraltimesto loosen

pulverized concrete from the walls of the hole. Vacuum again and repeat this step twice.

Step 2: Clean the Hole

*Vacuum hose

diameters vary.

Vacuum Attachment

may require 2 ½” - 1 ¼”

coupler depending on

vacuum model.

Remove a Smart Sensor probe from its protective

package. Remove white serial number strip from inside

the Smart Sensor (see step 4 below for serial number

strip placement instructions). If this is the rst time you

have used a Rapid RH™ system, please place the Rapid

RH™ Reader into the Smart Sensor. This preliminary

test will make it easier to align the reader once the Smart

Sensor is inserted into the concrete.

To properly insert the Reader, line up the white serial

number strip on the Smart Sensor with the white serial

number strip on the Rapid RH™ Reader. Insert the

Reader, twist 45 degrees clockwise and press the “ON” button. Verify that

numbers appear on the screen (see step 4 for instruction on taking readings)

Next, insert the Smart Sensor into the drilled hole. (Make sure that the Rapid

RH™ Reader is not installed in the Smart Sensor.) Use the orange plastic insert

tube attached to an orange cap and rmly press the Smart Sensor into the hole

until the Smart Sensor seats itself at the bottom of the hole.

For a 1¾” (44.5mm) deep hole, the top of the Smart Sensor will be approximately

¼” below the surface of the concrete.

For holes deeper than 1¾” (44.5mm) use the white insertion

tool (avaible at rapidrh.com).

To keep debris from getting into the Smart Sensor place

the protective cap with the orange insert into the Smart

Sensor until ready to take readings.

Follow ASTM F2170-02 procedures pertaining to

stabilization time. The Smart Sensor has an equilibration

time of 30 minutes to several hours depending on

concrete and conditions.

Step 3: Place the Probe

Installation Instructions

Insertion Tool (for deeper holes)

Remove the orange protective cap. Line up the white serial number strip on the

Rapid RH™ Reader with the white serial number strip on the Smart Sensor. Insert the

Rapid RH™Reader, push down slightly, twist

45 degrees clockwise and press the “ON”

button. If the display shows “- -” or “ER” the

Rapid RH™ Reader has not been inserted

properly or has been twisted too far. Remove

the Rapid RH™ Reader and try inserting

again. Press the “ON” button. The display

will toggle from the %RH reading and °F

temperature reading. The probe will shut off

automatically after approximately 1 minute

(you can remove the Reader at any time).

Record readings on the enclosed report form

that has spaces for information required by ASTM F2170-02 including the date,

time, %RH and temperature.You can use the grid at the bottom of the report form

to record probe locations. Each Smart Sensor is serialized on the outside of the

Smart Sensor. A copy of the serial number is located inside the Smart Sensor and

must be removed and may be used on the enclosed report form. Extra copies of

the report form can be obtained from our website, rapidrh.com.

After the initial equilibration time of 1-2 hours, subsequent readings can be taken

instantly. If future testing is needed, replace the orange tube attached to the orange

protective cap. The Rapid RH™ Reader can be left in the Smart Sensor covered by

an orange cap. However, if the relative humidity is above 95% it is recommended

that you remove the Rapid RH™ Reader between readings.

Step 4: Take Readings

If the probe will be covered (for example,

applied oor covering or coating), place the

stainless steel metal disk over the probe

and skim-coat the hole using a cementitious

patching compound compatible with the ooring

manufacturer’s installation instructions.

Relative humidity is one of many factors necessary for construction decisions. Wagner Electronics®

does not assume responsibility for any particular construction decision based on the readings of this

instrument and does not guarantee any specic construction results.

The method of use of this instrument and the interpretation of the readings are beyond the control

of the manufacturer. Wagner Electronics® cannot accept responsibility for any loss, consequential or

otherwise, resulting from the use of the Rapid RH™ and its accessories.

The Rapid RH™ should be used within two (2) years of purchase. If the probe does not appear to

function properly for any reason, return the probe to Wagner Electronics® for replacement.

The Rapid RH™ is patented under U.S. Patent 7,231,815.

For more information on relative humidity in concrete oors and moisture testing, go to

www.cement.org to order the book “Concrete Floors and Moisture” by Howard Kanare.

Step 5: Encapsulate the Probe

Orange Insert

The Rapid RH™ is intended for interior use only. It is imperative that the interior

application area be protected from weather elements such as rain and snow to

prevent water intrusion. The Rapid RH™ is not to be used in concrete less than

28 days old. Follow ASTM F2170-02, Standard Test Method for Determining

Relative Humidity in Concrete Floor Slabs using in situ Probes1.

NIST2traceable accuracy:

Readings at +/- 2% from 50% to 90% (at service conditions1)

Readings at +/- 3% up to 97% (at service conditions1)

Avoid severe cold or hot storage environments (i.e. vehicles)

1Available from ASTM International, P.O. Box C700, West Conshohocken, PA 19428-2959, http://www.astm.org

2National Institute of Standards and Technology

It is important to avoid condensation on the Rapid RH™ Smart Sensor. If the

sensor is colder than the dew point temperature of the environment being tested,

condensation can occur causing inaccurate readings and potentially damaging

the sensor. To avoid condensation on the sensor allow the probes to stabilize at

room temperature before removing from the package. This action is especially

important if you bring the Rapid RH™ Smart Sensor from a cold environment

(such as an unheated area of a vehicle) into a building.

Avoiding Condensation

Use Conditions

Wagner Electronic Products, Inc. warrants the Rapid RH™ Smart Sensor and Rapid RH™ Reader product against defects in material and workmanship for one (1) year from

the date of purchase, subject to the following terms and conditions:

Wagner’s liability under this warranty shall be limited, at Wagner’s option, to the repair or replacement of this product or any part thereof, which is demonstrated to be

defective. To exercise this warranty, customer must telephone, fax or e-mail Wagner’s Customer Service Department for a RMA (Return Materials Authorization) number and

factory instructions for shipment. This limited warranty does not apply if the product has been damaged by accident, negligent handling, misuse, alteration, damage during

shipment, or improper service. Wagner Electronic Products, Inc. shall in no event be liable for any breach of warranty or defect in this product, which exceeds the amount of

purchase price of the product.

With proper care and handling, the product should stay in calibration; however, because Wagner Electronic Products, Inc. has no control over the manner in which the unit

will be used, it makes no warranty that the Smart Sensors will stay in calibration for any specic period of time.

This warranty is in lieu of all other warranties, whether oral or written, express or implied. Any implied warranties, including implied warranties of merchantability

and tness for a particular purpose, are excluded. If this product is not in good working order as warranted above, the customer’s sole remedy shall be repair or

replacement as provided above.

This warranty is personal to the customer purchasing the product from Wagner Electronic Products, Inc. or from its authorized distributors and is not transferable.

The agents and employees of Wagner Electronic Products, Inc. are not authorized to make modications of this warranty or additional warranties binding on

Wagner Electronic Products, Inc. Accordingly, additional statements, whether oral or written, except written statements from an ofcer of Wagner Electronic Products, Inc. do