WAGO 753-514 User manual

Pos:2/Dokumentationallgemein/Einband/EinbandHandbuch- D e c kbl at t ohne Varia nt en fel d(S ta n dar d)@ 9\mod_1285229289866_0.docx @ 64941 @ @ 1
Manual
WAGO-I/O-SYSTEM 750
2DO 125V AC 0.5A/ Relay 2CO/ Potential Free
753-514
2-Channel Relay Output Module 125 VAC, 30 V
DC;
Isolated outputs; 2 changeover contacts
Version 1.1.0
Pos: 3 /Al le Ser ie n ( All ge m ein e M od ul e) /Hi nw eis e z ur Doku m ent ati o n/I mpr es su m für Sta nd ard h and büc h er - al lg. Ang aben, A nschr iften, Tel efo nnummer n und E-Mai l-Adr es s e n @ 3\mod_1219151118203_21.docx@ 21060@ @ 1

2 WAGO-I/O-SYSTEM 750
753-514 2DO 125V AC 0.5A/ Relay 2CO/ Potential Free
Manual
Version 1.1.0
© 2015 by WAGO Kontakttechnik GmbH & Co. KG
All rights reserved.
WAGO Kontakttechnik GmbH & Co. KG
Hansastraße 27
D-32423 Minden
Phone: [phone] – 0
Fax: [phone] – 1 69
E-Mail: [email protected]om
Web: http://www.wago.com
Technical Support
Phone: [phone] – 5 55
Fax: [phone] – 85 55
E-Mail: [email protected]om
Every conceivable measure has been taken to ensure the accuracy and
completeness of this documentation. However, as errors can never be fully
excluded, we always appreciate any information or suggestions for improving the
documentation.
E-Mail: [e-mail]
We wish to point out that the software and hardware terms as well as the
trademarks of companies used and/or mentioned in the present manual are
generally protected by trademark or patent.
=== Ende d er List e f ür T e xtm ar ke E i nb a nd_ v orn e == =

WAGO-I/O-SYSTEM 750 Table of Contents 3
753-514 2DO 125V AC 0.5A/ Relay 2CO/ Potential Free
Manual
Version 1.1.0
Pos: 5 /D o ku ment ati on allg em ein /V er zeic h nis se /I nhal ts ver z eic hni s - Ü b ersc hri ft oG u nd V er zei ch nis @ 3\mod_1219151230875_21.docx@21063 @ @ 1
Table of Contents
1Notes about this Documentation................................................................. 5
1.1 Validity of this Documentation................................................................. 5
1.2 Copyright................................................................................................... 5
1.3 Symbols..................................................................................................... 6
1.4 Number Notation....................................................................................... 8
1.5 Font Conventions ...................................................................................... 8
2Important Notes ........................................................................................... 9
2.1 Legal Bases ............................................................................................... 9
2.1.1 Subject to Changes ............................................................................... 9
2.1.2 Personnel Qualifications....................................................................... 9
2.1.3 Use of the WAGO-I/O-SYSTEM 750 in Compliance with
Underlying Provisions .......................................................................... 9
2.1.4 Technical Condition of Specified Devices ......................................... 10
2.2 Safety Advice (Precautions).................................................................... 11
3Device Description ..................................................................................... 13
3.1 View ........................................................................................................ 15
3.2 Connectors............................................................................................... 16
3.2.1 Data Contacts/Internal Bus................................................................. 16
3.2.2 Power Jumper Contacts/Field Supply ................................................ 17
3.2.3 CAGE CLAMP®Connectors ............................................................. 18
3.3 Display Elements .................................................................................... 19
3.4 Schematic Diagram ................................................................................. 20
3.5 Technical Data ........................................................................................ 21
3.5.1 Device................................................................................................. 21
3.5.2 Power Supply...................................................................................... 21
3.5.3 Communication .................................................................................. 21
3.5.4 Outputs ............................................................................................... 22
3.5.5 Connection.......................................................................................... 22
3.5.6 Climatic Environmental Conditions................................................... 22
3.5.7 Load Limiting Value Graph of the Relay........................................... 23
3.6 Approvals ................................................................................................ 24
3.7 Standards and Guidelines ........................................................................ 25
4Process Image ............................................................................................. 26
5Mounting..................................................................................................... 27
5.1 Mounting Sequence................................................................................. 27
5.2 Inserting and Removing Devices ............................................................ 28
5.2.1 Inserting the I/O Module .................................................................... 28
5.2.2 Removing the I/O Module.................................................................. 29
5.3 I/O Modules with Pluggable Wiring Level (Series 753) ........................ 30
5.3.1 Coding ................................................................................................ 31
5.3.2 Connector Removal ............................................................................ 33
6Connect Devices ......................................................................................... 34
6.1 Connecting a Conductor to the CAGE CLAMP®................................... 34
6.2 Connection Examples.............................................................................. 36

4 Table of Contents WAGO-I/O-SYSTEM 750
753-514 2DO 125V AC 0.5A/ Relay 2CO/ Potential Free
Manual
Version 1.1.0
6.2.1 1-Wire Connection, Protection Class I Actuators .............................. 36
6.2.2 1-Wire Protection Class II and III Actuators...................................... 36
6.3 Protective Circuits for Contacts of Relay Modules................................. 37
List of Figures ...................................................................................................... 39
List of Tables........................................................................................................ 40
=== En de der Lis te für T extmar ke Verz eich nis_vor ne == =

WAGO-I/O-SYSTEM 750 Notes about this Documentation 5
753-514 2DO 125V AC 0.5A/ Relay 2CO/ Potential Free
Manual
Version 1.1.0
Pos: 7 /Al le Seri en ( All ge mei ne M od ul e)/ Üb ersc hr ift en f ür al l e S eri en/H i nwei se zur D o ku ment ati on /Hi nw eise zu dies er D o kum ent atio n - Ü b er sc hri f t 1@ 4\mod_1237987661750_21.docx@ 29029 @ 1@ 1
1 Notes about this Documentation
Pos: 8 /Al le Ser ie n ( All ge m ein e M od ul e) /Hi nw eis e z ur Doku m ent ati o n/Hi n weis e/H i n weis : D o kum ent ati on auf be wahr e n @ 4\mod_1237987339812_21.docx@ 29026 @ @ 1
Always retain this documentation!
This documentation is part of the product. Therefore, retain the documentation
during the entire service life of the product. Pass on the documentation to any
subsequent user. In addition, ensure that any supplement to this documentation is
included, if necessary.
Pos: 9 /Al le S eri en ( Allg em eine M od ul e)/Ü bers chr ift en für all e S erie n/Hi n weis e zur Do ku ment ation /G ültig kei tsb erei ch - Ü b ers chr if t 2 @ 12\mod_1338912448776_21.docx@ 96469@ 2 @ 1
1.1 Validity of this Documentation
Pos: 10 / S eri e 750 ( WA GO-I/ O-SYST EM )/ Hi n weis e z ur Do kum e ntat i on/ Gül ti gk eits b erei c h/G ülti g k eits ber ei ch Dok um ent ati o n Bus kl e mme 750-x xxx, ohne V aria ntena ngabe @ 14 \mod_1358944037947_21.docx@ 109346@ @ 1
This documentation is only applicable to the I/O module 753-514
(2DO 125V AC 0.5A/ Relay 2CO/ Potential Free).
Pos: 11 / S eri e 750 ( WA GO-I/ O-SYST EM) /Hi n weis e z ur Do kume nt ati on/Hi n wei se /Ac ht ung : Hi nw eis z ur Do ku ment ati on B us kl emm en 750-xxxx @ 4\mod_1237986979656_21.docx@ 29023@ @ 1
The I/O module 753-514 shall only be installed and operated according to the
instructions in this manual and in the manual for the used fieldbus
coupler/controller.
Consider power layout of the WAGO-I/O-SYSTEM 750!
In addition to these operating instructions, you will also need the manual for the
used fieldbus coupler/controller, which can be downloaded at www.wago.com.
There, you can obtain important information including information on electrical
isolation, system power and supply specifications.
Pos: 12.1 /All e S eri en ( Al lg emei ne Mod ule) /Hi n weis e z ur D okumentation/Urheberschutzausführlich@ 4\mod_1235565145234_21.docx@ 27691@ 2 @ 1
1.2 Copyright
This Manual, including all figures and illustrations, is copyright-protected. Any
further use of this Manual by third parties that violate pertinent copyright
provisions is prohibited. Reproduction, translation, electronic and phototechnical
filing/archiving (e.g., photocopying) as well as any amendments require the
written consent of WAGO Kontakttechnik GmbH & Co. KG, Minden, Germany.
Non-observance will involve the right to assert damage claims.
Pos:12.2/Dokumentationallgemein/Gliederungselemente/---Seite nwe chs el--- @ 3\mod_1221108045078_0.docx @ 21810@ @ 1

6 Notes about this Documentation WAGO-I/O-SYSTEM 750
753-514 2DO 125V AC 0.5A/ Relay 2CO/ Potential Free
Manual
Version 1.1.0
Pos: 12.3 /All e Ser i en ( Al lg emei ne Mo dul e)/Ü ber s chri ft e n f ür alle Seri en/ Hi nw eis e z ur D o ku me nta tio n/ S y mbol e - Ü bers c hri ft 2 @ 13\mod_1351068042408_21.docx@ 105270@ 2 @ 1
1.3 Symbols
Pos: 12 .4.1 /Al le Seri en (All gemei ne Mod ule)/ Wichti ge Erl äuter unge n/Sich erheit s- undsonstigeHinweise/Gefahr/Gefahr:_WarnungvorPersonenschädenallgemein_- Er l äu ter ung @ 13\mod_1343309450020_21.docx@ 101029@ @ 1
Personal Injury!
Indicates a high-risk, imminently hazardous situation which, if not avoided, will
result in death or serious injury.
Pos: 12 .4.2 /Al le Seri en (All gemei ne Mod ule)/ Wichti ge Erl äut er u ng en/ S ich er h eits - u nd so ns ti ge H in wei s e/ Ge fahr /G ef ahr : _War nu ng vor P er so nen sc hä de n dur c h el ek tri sc he n S tro m_ - Erläuterung@ 13\mod_1343309694914_21.docx @ 101030 @ @ 1
Personal Injury Caused by Electric Current!
Indicates a high-risk, imminently hazardous situation which, if not avoided, will
result in death or serious injury.
Pos: 12 .4.3 /Al le Seri en (All gemei ne Mod ule)/ Wichti ge Erl äuter unge n/Sich erheit s- undsonstigeHinweis e/ War n ung / War n ung : _ W ar nu ng vor Pers one ns c h äde n al lg e mei n_ - Erläuterung@ 13\mod_1343309877041_21.docx@ 101035@ @ 1
Personal Injury!
Indicates a moderate-risk, potentially hazardous situation which, if not avoided,
could result in death or serious injury.
Pos: 12 .4.4 /Al le Seri en (All gemei ne Mod ule)/ Wichti ge Erl äuter unge n/Sich erheit s- und so ns ti ge H in wei s e/ Vors ic ht /V ors ich t: _War nu ng vor P ers on e nsc hä den allg e mei n_ - Erläuterung@ 13\mod_1343310028762_21.docx@ 101038@ @ 1
Personal Injury!
Indicates a low-risk, potentially hazardous situation which, if not avoided, may
result in minor or moderate injury.
Pos: 12 .4.5 /Al le Seri en (All gemei ne Mod ule)/ Wichti ge Erl äuter unge n/Sich erheit s- undsonstigeHinweise/Achtung/Achtung:_Warnung vorSachschädenal lg em ein_ - Erläuterung@ 13\mod_1343310134623_21.docx @ 101041 @ @ 1
Damage to Property!
Indicates a potentially hazardous situation which, if not avoided, may result in
damage to property.
Pos: 12.4 .6 /All e Serien ( Allge meine M odule) /Wic htige Er läut erung en/Si cherh eits- undsonstigeHinweise/Achtung/Achtung: _Warnung vorSachschädendurch elektrostatischeAufladung_ - Erläuterung@ 13\mod_1343310227702_21.docx@ 101044@ @ 1
Damage to Property Caused by Electrostatic Discharge (ESD)!
Indicates a potentially hazardous situation which, if not avoided, may result in
damage to property.
Pos: 12 .4.7 /Al le Seri en (All gemei ne Mod ule)/ Wichti ge Erl äuter unge n/Sich erheit s- undsonstigeHinweise/Hinweis/Hinweis:_ WichtigerHi nweis allgemein_ - Erläuterung@ 13\mod_1343310326906_21.docx@ 101047@ @ 1
Important Note!
Indicates a potential malfunction which, if not avoided, however, will not result in
damage to property.
Pos: 12 .4.8 /All e Serie n ( Al lg e mei ne Mod ule) / Wi c htig e Erlä ut er ung e n/ Si ch er hei ts- u nd sons ti g e H i nw eis e/I nf or ma ti o n/I nf or ma ti o n: _ W eit er e I nf or ma ti o n al lg e mei n_ - Erl äuter ung @ 13 \mod_1343310439814_21.docx@ 101051@ @ 1

WAGO-I/O-SYSTEM 750 Notes about this Documentation 7
753-514 2DO 125V AC 0.5A/ Relay 2CO/ Potential Free
Manual
Version 1.1.0
Additional Information:
Refers to additional information which is not an integral part of this
documentation (e.g., the Internet).
Pos:12.5/Dokumentationallgemein/Gliederungselemente/---Seite nwe chs el--- @ 3\mod_1221108045078_0.docx @ 21810@ @ 1

8 Notes about this Documentation WAGO-I/O-SYSTEM 750
753-514 2DO 125V AC 0.5A/ Relay 2CO/ Potential Free
Manual
Version 1.1.0
Pos: 12.6 /All e S eri en ( Al lg emei ne Mod ule) /Hi n weis e z ur D o ku ment at i on /Za hl e ns ys t eme @ 3\mod_1221059454015_21.docx@ 21711@ 2 @ 1
1.4 Number Notation
Table 1: Number Notation
Number Code
Example
Note
Decimal
100
Normal notation
Hexadecimal
0x64
C notation
Binary
'100'
'0110.0100'
In quotation marks, nibble separated with
dots (.)
Pos: 12.7 /All e S eri en ( Al lg emei ne Mod ule) /Hi n weis e z ur D o ku ment ati on /Sc hri ft kon venti o ne n @ 3\mod_1221059521437_21.docx@ 21714 @ 2 @ 1
1.5 Font Conventions
Table 2: Font Conventions
Font Type
Indicates
italic
Names of paths and data files are marked in italic-type.
e.g.: C:\Program Files\WAGO Software
Menu
Menu items are marked in bold letters.
e.g.: Save
>
A greater-than sign between two names means the selection of a
menu item from a menu.
e.g.: File > New
Input
Designation of input or optional fields are marked in bold letters,
e.g.: Start of measurement range
“Value”
Input or selective values are marked in inverted commas.
e.g.: Enter the value “4 mA” under Start of measurement range.
[Button]
Pushbuttons in dialog boxes are marked with bold letters in square
brackets.
e.g.: [Input]
[Key]
Keys are marked with bold letters in square brackets.
e.g.: [F5]
Pos: 13 / D o kum e nt atio n allg emei n/ Gl ie der ung s el e me nte /---Sei t e n wec hs el--- @ 3\mod_1221108045078_0.docx @ 21810@ @ 1

WAGO-I/O-SYSTEM 750 Important Notes 9
753-514 2DO 125V AC 0.5A/ Relay 2CO/ Potential Free
Manual
Version 1.1.0
Pos: 14 /Al l e Ser i en ( All ge mei ne M od ule) /Ü b ersc hri fte n f ür alle Seri en/WichtigeErläuterungen/WichtigeErläuterungen - Üb ersc hr if t 1 @ 4\mod_1241428899156_21.docx@ 32170@ 1 @ 1
2 Important Notes
Pos: 15 .1 /All e Seri en( Allg emeine D okum ente) ( Allg emeine M odule) /Wic htige Er läut erung en/Wi chtig e Erlä uteru ngen - Einl ei t ung @ 3\mod_1221059818031_21.docx@ 21717 @ @ 1
This section includes an overall summary of the most important safety
requirements and notes that are mentioned in each individual section. To protect
your health and prevent damage to devices as well, it is imperative to read and
carefully follow the safety guidelines.
Pos: 15 .2 /All e Seri en( Allg emeine M odul e)/Ü berschr ifte nf ür alle S erie n/Wich tige Er läuter ung enRec htlic he Grun dlag en -Ü ber sc hr ift 2 @ 3\mod_1221060626343_21.docx@ 21726@ 2 @ 1
2.1 Legal Bases
Pos: 15.3/AlleSerien(AllgemeineDokumente)( AllgemeineModule)/Wichtige Erläuterungen/Änderungsvorbehalt- Über schr ift 3 und In halt @ 3\mod_1221060036484_21.docx@ 21720@ 3 @ 1
2.1.1 Subject to Changes
WAGO Kontakttechnik GmbH & Co. KG reserves the right to provide for any
alterations or modifications that serve to increase the efficiency of technical
progress. WAGO Kontakttechnik GmbH & Co. KG owns all rights arising from
the granting of patents or from the legal protection of utility patents. Third-party
products are always mentioned without any reference to patent rights. Thus, the
existence of such rights cannot be excluded.
Pos:15.4/Serie750(WAGO-I/O-S YST EM )/ Wi c hti g e Er lä ut er u ng en/ Per s on al q ual if i kat io nP ers on alq u ali fi ka ti on 750- xxxx - Ü bersc hrift 3 und I nhalt @ 3\mod_1224061208046_21.docx@ 24063@ 3 @ 1
2.1.2 Personnel Qualifications
All sequences implemented on WAGO-I/O-SYSTEM 750 devices may only be
carried out by electrical specialists with sufficient knowledge in automation. The
specialists must be familiar with the current norms and guidelines for the devices
and automated environments.
All changes to the coupler or controller should always be carried out by qualified
personnel with sufficient skills in PLC programming.
Pos:15.5/Serie750( WAGO-I/ O-SYSTEM)/Wichtige Erläuterungen/BestimmungsgemäßeVerwendungBestimmungsgemäßeVerwendung750-xxxx- Ü b ers chr if t 3 un d I n hal t @ 3\mod_1224064151234_21.docx@ 24070 @ 3 @ 1
2.1.3 Use of the WAGO-I/O-SYSTEM 750 in Compliance with
Underlying Provisions
Fieldbus couplers, fieldbus controllers and I/O modules found in the modular
WAGO-I/O-SYSTEM 750 receive digital and analog signals from sensors and
transmit them to actuators or higher-level control systems. Using programmable
controllers, the signals can also be (pre-) processed.
The devices have been developed for use in an environment that meets the IP20
protection class criteria. Protection against finger injury and solid impurities up to
12.5 mm diameter is assured; protection against water damage is not ensured.
Unless otherwise specified, operation of the devices in wet and dusty
environments is prohibited.
Operating the WAGO-I/O-SYSTEM 750 devices in home applications without
further measures is only permitted if they meet the emission limits (emissions of
interference) according to EN 61000-6-3. You will find the relevant information
in the section “Device Description” > “Standards and Guidelines” in the manual
for the used fieldbus coupler/controller.

10 Important Notes WAGO-I/O-SYSTEM 750
753-514 2DO 125V AC 0.5A/ Relay 2CO/ Potential Free
Manual
Version 1.1.0
Appropriate housing (per 94/9/EG) is required when operating the WAGO-I/O-
SYSTEM 750 in hazardous environments. Please note that a prototype test
certificate must be obtained that confirms the correct installation of the system in
a housing or switch cabinet.
Pos: 15 .6 /All e Seri en( Allg emeine D okum ente) ( Allg emeine M odule) /Wic htige Er läut erung en/T echnis cher Z ustan d der Ger äte - Übers chri ft 3 und Inh alt @ 3\mod_1221060446109_21.docx@ 21723@ 3 @ 1
2.1.4 Technical Condition of Specified Devices
The devices to be supplied ex works are equipped with hardware and software
configurations, which meet the individual application requirements. WAGO
Kontakttechnik GmbH & Co. KG will be exempted from any liability in case of
changes in hardware or software as well as to non-compliant usage of devices.
Please send your request for modified and new hardware or software
configurations directly to WAGO Kontakttechnik GmbH & Co. KG.
Pos:15.7/Dokumentationallgemein/Gliederungselemente/---Seite nwe chs el--- @ 3\mod_1221108045078_0.docx @ 21810 @ @ 1

WAGO-I/O-SYSTEM 750 Important Notes 11
753-514 2DO 125V AC 0.5A/ Relay 2CO/ Potential Free
Manual
Version 1.1.0
Pos: 15.8 /All e S eri en ( Al lg emei ne Mod ule) /Ü bers chr ift e n f ür alle S er ie n/Wi ch tig e E rlä uter u ngen Sic her hei t shi nwei s e - Üb ers c hri ft 2 @ 6 \mod_1260180299987_21.docx@ 46724@ 2 @ 1
2.2 Safety Advice (Precautions)
Pos: 15.9 /All e S eri en ( Al lg emei ne Doku m ente) (Al lg emei ne Mod ule) /Wi c htig e Er lä ut eru nge n/ Sich erh eits hi n weis e/ Einl ei tung Sic her hei ts hin wei se H ar dw are @ 6\mod_1260180170493_21.docx @ 46720@ @ 1
For installing and operating purposes of the relevant device to your system the
following safety precautions shall be observed:
Pos: 15.1 0. 1 / Al l e S er ie n ( All g em ei ne D o ku ment e) (All g em ei ne M o dul e) / Wich ti g e E rl ä uter u ng en /Sic h erh ei ts hi nw eis e /G ef ahr /G ef ahr : Nich t an G erät e n unter Spa nn ung ar beit e n! @ 6\mod_1260180365327_21.docx@ 46727@ @ 1
Do not work on devices while energized!
All power sources to the device shall be switched off prior to performing any
installation, repair or maintenance work.
Pos: 15.1 0. 2 / S er ie 750 ( W AG O-I/O-SY ST EM) /Wic htig e Er läu ter ung en/ Sic her heit s- und s o nsti g e H i n w eis e/ G ef ahr/ Ge fa hr : Einb au 0750-x xxx nur i n Gehäus e n, Schr än ken oder ele ktri sc he n B etr ie bsr ä ume n! @ 6\mod_1260180556692_21.docx@ 46731@ @ 1
Install the device only in appropriate housings, cabinets or in electrical
operation rooms!
The WAGO-I/O-SYSTEM 750 and its components are an open system. As such,
install the system and its components exclusively in appropriate housings,
cabinets or in electrical operation rooms. Allow access to such equipment and
fixtures to authorized, qualified staff only by means of specific keys or tools.
Pos: 15.1 0. 3 / Al l e S er ie n ( All g em ei ne D o ku ment e) (All g em ei ne M o dul e) / Wich ti g e E rl ä uter u ng en /Sic h erh ei ts hi nw eis e /G ef ahr /G ef ahr : Unfal l v erh üt ung s v ors c hri ft en beac h te n! @ 6\mod_1260180657000_21.docx@ 46735@ @ 1
Pos: 15.1 0. 4 / Al le Ser ie n (Al l ge m ein e D o k ume nt e) ( Al lg e m ein e M o dul e) / Wi ch tig e Erlä uter u ngen /S ic h er h eits hi n wei se /G ef ahr /G ef ahr : Auf n or mg er ec ht e n A nsc hl u ss acht en! @ 6 \mod_1260180753479_21.docx@ 46739@ @1
Pos: 15.1 1 /Al le S eri en ( Allg em ein e Mo dul e)/ Wich tig e Er lä uter ung en /Si c h er hei ts- un d s o nst ig e Hin wei se /G ef a hr/ G ef ahr: Lei t ung en nur i n s pa n nu ng sfr ei e m Z ust a nd ansc hl ies s e n od er tren n en @ 16\mod_1372153982130_21.docx@ 124277@ @ 1
Only connect or disconnect lines when power is safely isolated!
The lines to the device can carry hazardous voltages and currents. Contact with
the lines when live can result in severe injury or death. Therefore, read and
observe the following safety rules before you perform work on the device:
1. Disconnect the respective system component from the power supply.
2. Secure the system component against unintentional restart.
3. Check if the voltage is positively isolated.
Pos: 15.1 2. 1 / Al l e S er ie n ( All g em ei ne D o ku ment e) (All g em ei ne M o dul e) / Wich ti g e E rl ä uter u ng en /Sic h erh ei ts hi nw eis e /Ac ht u ng /Ac ht u ng : De fe k t e od er besc h ädig t e Gerät e austa us c h en! @ 6\mod_1260180857358_21.docx @ 46743@ @ 1
Replace defective or damaged devices!
Replace defective or damaged device/module (e.g., in the event of deformed
contacts), since the long-term functionality of device/module involved can no
longer be ensured.
Pos: 15.1 2. 2 / Al l e S er ie n ( All g em ei ne D o ku ment e) (All g em ei ne M o dul e) / Wich ti g e E rl ä uter u ng en /Sic h erh ei ts hi nw eis e /Ac ht u ng /Ac ht u ng : G erä te vor kriec he nde n und i s ol ier e nden Sto ff en schüt z en! @ 6\mod_1260181036216_21.docx@ 46747 @ @ 1

12 Important Notes WAGO-I/O-SYSTEM 750
753-514 2DO 125V AC 0.5A/ Relay 2CO/ Potential Free
Manual
Version 1.1.0
Protect the components against materials having seeping and insulating
properties!
The components are not resistant to materials having seeping and insulating
properties such as: aerosols, silicones and triglycerides (found in some hand
creams). If you cannot exclude that such materials will appear in the component
environment, then install the components in an enclosure being resistant to the
above-mentioned materials. Clean tools and materials are imperative for handling
devices/modules.
Pos: 15.1 2. 3 / Al l e S er ie n ( All g em ei ne D o ku ment e) (All g em ei ne M o dul e) / Wich ti g e E rl ä uter u ng en /Sic h erh ei ts hi nw eis e /Ac ht u ng /Ac ht u ng : Rei nig u ng nur mit zul äss ig e n M at er ial ie n! @ 6\mod_1260181203293_21.docx @ 46751@ @ 1
Clean only with permitted materials!
Clean soiled contacts using oil-free compressed air or with ethyl alcohol and
leather cloths.
Pos: 15.1 2. 4 / Al l e S er ie n ( All g em ei ne D o ku ment e) (All g em ei ne M o dul e) / Wich ti g e E rl ä uter u ng en /Sic h erh ei ts hi nw eis e /Ac ht u ng /Ac ht u ng : K ei n K o nt akts pr a y verwe nd e n! @ 6\mod_1260181290808_21.docx@ 46755@ @ 1
Do not use any contact spray!
Do not use any contact spray. The spray may impair contact area functionality in
connection with contamination.
Pos: 15.1 2. 5 / Al l e S er ie n ( All g em ei ne D o ku ment e) (All g em ei ne M o dul e) / Wich ti g e E rl ä uter u ng en /Sic h erh ei ts hi nw eis e /Ac ht u ng /Ac ht u ng : V erp ol ung ver mei de n! @ 6\mod_1260184045744_21.docx@ 46767@ @ 1
Do not reverse the polarity of connection lines!
Avoid reverse polarity of data and power supply lines, as this may damage the
devices involved.
Pos: 15.1 2. 6 / Al l e S er ie n ( All g em ei ne D o ku ment e) (All g em ei ne M o dul e) / Wich ti g e E rl ä uter u ng en /Sic h erh ei ts hi nw eis e /Ac ht u ng /Ac ht u ng : El e ktr os t atis c h e Ent l a du ng verm eid e n! @ 6\mod_1260181364729_21.docx@ 46759@ @ 1
Avoid electrostatic discharge!
The devices are equipped with electronic components that may be destroyed by
electrostatic discharge when touched. Please observe the safety precautions
against electrostatic discharge per DIN EN 61340-5-1/-3. When handling the
devices, please ensure that environmental factors (personnel, work space and
packaging) are properly grounded.
Pos: 16 /D o kum ent at io n allge mei n/ G li e der ung s el em e nte /---Sei t en we chs el --- @ 3\mod_1221108045078_0.docx@ 21810 @ @ 1

WAGO-I/O-SYSTEM 750 Device Description 13
753-514 2DO 125V AC 0.5A/ Relay 2CO/ Potential Free
Manual
Version 1.1.0
Pos: 17 /A lle Ser ien (Al lge meine Mo dule)/ Über schrif ten für all e Serie n/Gerä teb eschrei bung /Gerä tebes chrei bung - Üb er sc hr ift 1 @ 3\mod_1233756084656_21.docx@ 27096@ 1 @ 1
3 Device Description
Pos: 18 .1.1 /S erie 750 ( WAGO -I/O-SYST EM )/G erä te bes c hrei bu ng/Ei nl ei tu ng/A n wen dung /D O/A nw end ung 750-05 xx D O R el ais @ 5\mod_1246611276875_21.docx@36561 @ @ 1
The 753-514 Digital Output Module transmits binary control signals from the
automation device to the connected actuators (e.g., solenoid valves, contactors,
transmitters, relays or other electrical loads).
Pos: 18 .1.2 /S erie 750 ( W AG O-I/ O-SYST EM )/G erä te bes chr ei bu ng/Ei nl ei tung /I/ O-B esc hrei bu ng /DO /I / O-B esc hr ei bu ng 750-0 514 2 D O 2-L eiter (DO oder / DO) @ 22\mod_1425475259743_21.docx @ 176742@ @ 1
The I/O module has 2 output channels, providing for direct connection of
actuators to the CAGE CLAMP®connectors DO 1 or /DO 1 of channel 1 and an
external N potential or DO 2 or /DO 2 of channel 2 and an external N potential.
Pos: 18 .1.3 /S erie 750 ( WAGO -I/O-SYST EM )/G erä te bes c hrei bu ng/Ei nl ei tu ng/I/ O-B es c hr ei bu ng /Al lg e m ein / V er wei s auf K api tel " A ns c hlüss e" @ 8\mod_1276775378035_21.docx@ 57956@ @ 1
The assignment of the connections is described in the “Connectors” section.
Pos: 18 .1.4 /S erie 750 ( WAGO -I/O-SYST EM )/G erä te bes c hrei bu ng/Ei nl ei tu ng/I/ O-B es c hr ei bu ng /Al lg e m ein / V er wei s auf K api tel " G erät e ansc hli eß en" > "A nsc hlus sb eis pi el (e) " @ 5\mod_1246015203281_21.docx @ 36298@ @ 1
Connection examples are shown in section “Connecting Devices” > … >
“Connection Example(s)”.
Pos: 18 .1.5 /S erie 750 ( WAGO -I/O-SYST EM )/G erä te bes c hrei bu ng/Ei nl ei tu ng/I/ O-Besc hr ei bu ng /D O /I/ O-B es c hr ei bu ng 75 0-051 4R el aiskont akte 1 1 und 21 @ 2 2\mod_1425462562262_21.docx@ 176626@ @ 1
An external potential of 125 VAC can be applied to relay contacts 11 and 21.
Pos: 18 .1.6 /S erie 750 ( WAGO -I/O-SYST EM )/ Wi ch tig e Erläut er u ng en/Si c h erh eits - undsonstigeHinweise/Achtung/Achtung:DO InduktionsspannungsbegrenzungRelais@ 5\mod_1247031985231_21.docx@ 36766@ @ 1
Inductive loads must be dampened!
For the protection of relay coils and contacts, inductive loads must be dampened
with an effective protection circuit!
Examples of protection circuits can be seen in the section “Protective Circuits for
Contacts of Relay Modules”.
Pos: 18 .1.7 /S erie 750 ( WAGO -I/O-SYSTEM)/Wichtige Erläuterungen/Sicherheits- und so nstige H inwei se/A chtung /Ach tung: Verl ust vo n Eigens chaft en durc h hohe Sc haltl eistung ! @ 22\mod_1425462925724_21.docx @ 176630@ @ 1
Loss of properties due to high switching power!
To prevent the gold layer from being damaged, 30 VDC switching voltages and
50 mA currents must not be exceeded. Higher switching power with switching arc
eventually evaporates the gold layer. This can cause the relay to lose its properties
in regards to minimum switching current.
Pos: 18 .1.8 /S erie 750 ( WAGO -I/O-SYST EM )/G erä te bes c hrei bu ng/Ei nl ei tu ng/I/ O-B esc hrei bu ng /DO / I/ O-B esc hrei bu ng 750-0 5 xx W ec hsler @ 5\mod_1246866311313_21.docx@ 36609@ @ 1
The I/O module incorporates two change-over relays connected potential free.
This means on the field side only the connections of the relay contacts are present.
Therefore, both relays can be operated with different voltages.
Because of the potential free contacts also a serial connection of the two relays is
possible as well as a serial connection of several relays with block wise
connection of several modules.
Pos: 18 .1.9 /S erie 750 ( WAGO -I/O-SYST EM )/G erä te bes c hrei bu ng/Ei nl ei tu ng/I/ O-B esc hrei bu ng /DO / I/ O-B esc hrei bu ng 750-0 514, -517 Durc hsc h al tu ng des mittl er en R elai s ko nt a kt es @ 22\mod_1425393644292_21.docx@ 176581@ @ 1
Depending on the relay status the voltage of the middle contact 11 resp. 21 is
switched to the lower contact 12 resp. 22 or to the upper contact 14 resp. 24. In
the OFF state the contacts 11 resp. 21 are switched to the lower contacts 12 resp.
22.
Pos: 18.1 .1 0 / S er ie 750 ( W AG O-I/O-SY ST EM) /G er ät e be schr eib ung / Ei nl ei t ung / I/O-Be schr eibu ng/DO/ I/O-Beschreibung750-05xxAnsteuerungderR elais (Interne Systemspannung) @ 5\mod_1246861676649_21.docx@ 36599@ @ 1
The internal system voltage is used to trigger the relays.
Pos: 18.1 .1 1 / S er ie 750 ( W AG O-I/O-SY ST EM) /G er ät e be schr eib ung / Ei nl ei t ung / LED -A nzei g e /L ED Z us ta nd Rel ais @ 5\mod_1246862048946_21.docx@ 36603@ @ 1
The switching status of the two relays is indicated via green status LEDs.
Pos: 18.1 .1 2 / S er ie 750 ( W AG O-I/O-SY ST EM) /G er ät e be schr eib ung / Ei nl ei t ung / LED -A nzei g e /V er weis auf Kapi tel " A nzei g eel e me nt e" @ 5 \mod_1246010525000_21.docx@ 36194 @ @ 1
The meaning of the LEDs is described in the “Display Elements” section.

14 Device Description WAGO-I/O-SYSTEM 750
753-514 2DO 125V AC 0.5A/ Relay 2CO/ Potential Free
Manual
Version 1.1.0
Pos: 18.1 .1 3 / S er ie 750 ( W AG O-I/O-SY ST EM) /Wic htig e Er läu ter ung en/ Sic her heit s- und s o nsti ge H i nw eis e/ Ac htu ng /Ac ht ung : M a xim aler Str o m Lei s tu ngs ko nta kt e 1 0 A @ 3\mod_1226499143500_21.docx@ 25029 @ @ 1
Do not exceed maximum current via power jumper contacts!
The maximum current to flow through the power jumper contacts is 10 A.
Greater currents can damage the contacts.
When configuring your system, ensure that this current is not exceeded. If
exceeded, insert an additional supply module.
Pos: 18.1 .1 4 / S er ie 750 ( W AG O-I/O-SY ST EM) /G er ät e be schr eib ung / Ei nl ei t ung / Ver sor g u ng /A nor d nu ng u nt er Ber üc ksi c hti gu ng der Leis t ungs kon ta kt e b el ie big @ 3 \mod_1233756233468_21.docx@ 27099 @ @ 1
With consideration of the power jumper contacts, the individual modules can be
arranged in any combination when configuring the fieldbus node. An arrangement
in groups within the group of potentials is not necessary.
Pos: 18.1 .1 5 / S er ie 750 ( W AG O-I/O-SY ST EM) /G er ät e be schr eib ung / Ei nl ei t ung / V er sor g ung / V ers org ung Erd-PotentialüberLeistungskontakt@ 5\mod_1246868578453_21.docx@ 36622@ @ 1
The I/O module receives the earth potential for the field level from an upstream
I/O module via the power contacts used as blade contacts. It then provides this
potential to subsequent I/O modules via the power contacts used as spring
contacts.
Pos: 18.1 .1 6 / S er ie 750 ( W AG O-I/O-SY ST EM) /Wic htig e Er läu ter ung en/ Sic her heit s- und s o nsti ge H i nw eis e/ Hin w eis/ Hi n weis : P ot ent ial ei ns pei s ekl em me eins etz e n! ( nur LK für Erde)@ 18\mod_1395131828626_21.docx @ 148188@ @ 1
Use the supply module!
The I/O module is equipped with an integrated power contact for relaying the
ground potential.
When required, use a power supply module for the field-side supply of the
following I/O modules.
#
Pos: 18.1 .1 7 / S er ie 750 ( W AG O-I/O-SY ST EM) /G er ät e be schr eib ung / Ei nl ei t ung / Ein sa tz b erei c h/ Ei ns a tzb er eic h 750-xxx x al le Kop pler/ C ontr oll er o h ne E i nsc hrä nku ng @ 3\mod_1232541691906_21.docx@26522 @ @ 1
The I/O module 753-514 can be used with all fieldbus couplers/controllers of the
WAGO-I/O-SYSTEM 750.
Pos:18.2/Dokumentationallgemein/Gliederungselemente/---Seite nwe chs el--- @ 3\ mod_1221108045078_0.docx@ 21810@ @ 1

WAGO-I/O-SYSTEM 750 Device Description 15
753-514 2DO 125V AC 0.5A/ Relay 2CO/ Potential Free
Manual
Version 1.1.0
Pos: 18.3 /All e Ser i en ( Al lg emei ne Mo dul e)/Ü ber s chri ft e n f ür alle Seri en/ Ger ä te bes c hrei bu ng /A nsic ht - Ü b ers chr if t 2 @ 4\mod_1240984217343_21.docx@ 31958@ 2 @ 1
3.1 View
Pos:18.4/Serie753(WAGO-I/O-SYST EM )/H i n weis e z ur D o kum ent ati on/ Hi n wei s z u m Z ub ehör t eil 753-110 @ 20\mod_1411023611789_21.docx@ 163868@ @ 1
Depiction of the I/O module with 753-110 Connector!
Information on this pluggable connection pertains to the 753-110 Connector,
which is not included with the I/O module.
Pos:18.5/Serie753(WAGO-I/O-S YST EM) / Ger äte b esc hr ei bung /A nsi c ht /Di gi tala usg a ng s klem me n/A nsi c ht 7 53-0 514 @ 22\mod_1425565763768_21.docx@ 176970@ @ 1
Figure 1: View
Pos:18.6/Serie753( WAGO-I/ O-SYST EM) / Ger äte b esc hrei bu ng /A nsi c ht / A nsi c ht – Legen de mit 1 LK, mit Ko dier ung, Ka belbe festig ung und Pr üföf fnung en @ 22\mod_1425565508846_21.docx@176967@ @ 1
Table 3: Legend for Figure “View”
Pos.
Description
Details See Section
1
Marking possibility with Mini-
WSB
---
2
Status-LEDs
“Device Description” > “Display
Elements”
3
Data contacts
“Device Description” > “Connectors”
4
CAGE CLAMP®connectors
“Device Description” > “Connectors”
5
Release tab
“Mounting” > “Inserting and Removing
Devices” and “I/O Modules with
Pluggable Wiring Level (Series 753)”
6
Coding possibility with coding
fingers
“Mounting” > “Coding”
7
Test port
---
8
Power jumper contacts
“Device Description” > “Connectors”
9
Fixing lug for cable ties
“Mounting” > “I/O Modules with
Pluggable Wiring Level (Series 753)”
Pos:18.7/Dokumentationallgemein/Gliederungselemente/---Seite nwe chs el--- @ 3\mod_1221108045078_0.docx @ 21810@ @ 1

16 Device Description WAGO-I/O-SYSTEM 750
753-514 2DO 125V AC 0.5A/ Relay 2CO/ Potential Free
Manual
Version 1.1.0
Pos: 18.8 /All e S eri en ( Al lg emei ne Mod ule) /Ü ber s chr ift e n f ür alle Ser ie n/G erä te bes c hrei bu ng /A nsc hl üs se - Ü b ersc hr if t 2 @ 4\mod_1240984262656_21.docx@ 31961@ 2 @ 1
3.2 Connectors
Pos:18.9/Serie750(WAGO-I/O-S YST EM) /Ger äte b esc hrei bu ng/A nsc hl üs se/ Da ten kon tak te/ Kl em men bus -Ü ber sc hri ft 3 @ 6\mod_1256294684083_21.docx@ 43660@ 3 @ 1
3.2.1 Data Contacts/Internal Bus
Pos: 18.1 0. 1 / S er ie 750 ( W AG O-I/O-SY ST EM) /G er ät e be schr eib ung / A nsc hlüs s e/D at e n kont a kt e - F el dbus k oppl er /-co ntr oller , A bbil du ng und Beschr ei bung @ 3\mod_1231771259187_21.docx@ 26002@ @ 1
Communication between the fieldbus coupler/controller and the I/O modules as
well as the system supply of the I/O modules is carried out via the internal bus. It
is comprised of 6 data contacts, which are available as self-cleaning gold spring
contacts.
Figure 2: Data Contacts
Pos: 18.1 0. 2 / S er ie 750 ( W AG O-I/O-SY ST EM) /Wic htig e Er läu ter ung en/ Sic her heit s- und s o nsti g e H i n w eis e/ Ac ht u ng /Ac ht ung : Bus kl em me n ni ch t auf G ol df ed er ko nt a kte l eg e n! @ 7\mod_1266318463636_21.docx@ 50695@ @ 1
Do not place the I/O modules on the gold spring contacts!
Do not place the I/O modules on the gold spring contacts in order to avoid soiling
or scratching!
Pos: 18.1 0. 3 / S er ie 750 ( W AG O-I/O-SY ST EM) /Wic htig e Er läu ter ung en/ Sic her heit s- und s o nsti ge H i nw eis e/ Ac htu ng /Ac ht ung : E SD - Auf guteErdungder Umgebung achten!@ 7\mod_1266318538667_21.docx@ 50708@ @ 1
Ensure that the environment is well grounded!
The devices are equipped with electronic components that may be destroyed by
electrostatic discharge. When handling the devices, ensure that the environment
(persons, workplace and packing) is well grounded. Avoid touching conductive
components, e.g. data contacts.
Pos: 18.1 1 /D o kum ent ati on al lg em ei n/Gli ed eru ng sel e ment e/---S eit en wec hs el--- @ 3 \mod_1221108045078_0.docx@ 21810@ @ 1

WAGO-I/O-SYSTEM 750 Device Description 17
753-514 2DO 125V AC 0.5A/ Relay 2CO/ Potential Free
Manual
Version 1.1.0
Pos: 18.1 2 / S er ie 750 ( W AG O-I/ O-SYST EM) /G er ät e be schr eib u ng /A nsc hlüs s e/ L eis t ungs ko nta kt e/ F eld v ers or g ung - Ü b ers chr if t 3 @ 6 \mod_1256294692864_21.docx@ 43664@ 3 @ 1
3.2.2 Power Jumper Contacts/Field Supply
Pos: 18.1 3. 1 / S er ie 750 ( W AG O-I/O-SY ST EM) /Wic htig e Er l äuter ung en /Sic her hei ts- un d s o ns tig e Hi n wei se /V or si ch t/ Vor si c ht: Ver let zu ng sg ef a hr durc h sc har f ka ntig e Mes ser k on ta kt e! @ 6\mod_1256193279401_21.docx@ 43414@ @ 1
Risk of injury due to sharp-edged blade contacts!
The blade contacts are sharp-edged. Handle the I/O module carefully to prevent
injury.
Pos: 18.1 3. 2 / S er ie 750 ( W AG O-I/O-SY ST EM) /G er ät e be schr eib ung / A nsc hlüs s e/ L eis t ungs kon ta kt 1 LK (Mess er /F ed er ) - Ei nl eitu ng @ 18\mod_1393922127812_21.docx@ 146986 @ @ 1
The I/O module 753-514 has 1 self-cleaning power jumper contact that supply and
transmit power for the field side. The contact on the left side of the I/O module is
designed as male contact and the contact on the right side as spring contact.
Pos: 18.1 3. 3 / S er ie 753 ( W AG O-I/O-SY ST EM) /G er ät e be schr eib ung / A nsc hlüs s e/ L eis t ungs kon ta kt 1 LK (Mess er /F ed er ) - Ab bild ung (ein fach e Breit e) @ 20\mod_1407152952622_21.docx@ 161111@ @ 1
Figure 3: Power Jumper Contacts
Pos: 18.1 3. 4 / S er ie 750 ( W AG O-I/O-SY ST EM ) /G er ät ebe s chr ei b ung / Ans c hl üss e/ L ei st ung s kon ta kt 1 LK (Mess er /F ed er) - Legen de @ 18\mod_1393926089446_21.docx @ 147000@ @ 1
Table 4: Legend for Figure “Power Jumper Contacts”
Contact
Type
Function
1
Spring contact
Potential transmission (Earth) for field supply
2
Blade contact
Potential feed-in (Earth) for field supply
Pos: 18.1 3. 5 / S er ie 750 ( W AG O-I/O-SY ST EM) /Wic htig e Er läu ter ung en/ Sic her heit s- und s o nsti ge H i nw eis e/ Ac htu ng /Ac ht ung : M a xim aler Str o m Lei s tu ngs ko nta kt e 1 0 A @ 3\mod_1226499143500_21.docx@ 25029 @ @ 1
Do not exceed maximum current via power jumper contacts!
The maximum current to flow through the power jumper contacts is 10 A.
Greater currents can damage the contacts.
When configuring your system, ensure that this current is not exceeded. If
exceeded, insert an additional supply module.
Pos: 18.1 4 /D o kum ent ati on al lg em ei n/Gli ed eru ng sel e ment e/---S eit en wec hs el--- @ 3 \mod_1221108045078_0.docx@ 21810@ @ 1

18 Device Description WAGO-I/O-SYSTEM 750
753-514 2DO 125V AC 0.5A/ Relay 2CO/ Potential Free
Manual
Version 1.1.0
Pos: 18.1 5 / S er ie 750 ( W AG O-I/ O-SYST EM) /G er ät e be schr eib u ng /A nsc hlüs s e/C A G E C L AMP- Anschlüsse - Ü ber sc hr ift 3 @ 6\mod_1256296337770_21.docx@ 43674@ 3 @ 1
3.2.3 CAGE CLAMP®Connectors
Pos: 18.1 6 /S eri e 7 53 (W AG O-I/ O-SYSTEM)/Hinweisezur Dokumentation/HinweiszumZubehörteil753-110 @ 20\mod_1411023611789_21.docx@ 163868@ @ 1
Depiction of the I/O module with 753-110 Connector!
Information on this pluggable connection pertains to the 753-110 Connector,
which is not included with the I/O module.
Pos: 18.1 7 / S er ie 753 ( W AG O-I/ O-SYST EM ) /G erät e bes chr ei bu ng /A nsc hlüs s e/Di gi t ala usg a ngs kle m me n/A nsc hl üs se 7 5 3-051 4 @ 22\mod_1425570063603_21.docx@ 176987@ @ 1
Figure 4: CAGE CLAMP®Connectors
Table 5: Legend for Figure “CAGE CLAMP®Connectors”
Channel
Designation
Connector
Function
1
14
1
Output DO 1:
Normally open contact
11
2
Load line
12
3
Output /DO 1:
Normally closed contact
Ground
4
Field supply ground
2
24
5
Output DO 2:
Normally open contact
21
6
Load line
22
7
Output /DO 2:
Normally closed contact
Ground
8
Field supply ground
Pos: 18.1 8 /D o kum ent ati on al lg em ei n/Gli ed eru ng sel e ment e/---S eit en wec hs el--- @ 3 \mod_1221108045078_0.docx@ 21810@ @ 1

WAGO-I/O-SYSTEM 750 Device Description 19
753-514 2DO 125V AC 0.5A/ Relay 2CO/ Potential Free
Manual
Version 1.1.0
Pos: 18.1 9 / Al l e S er ie n ( All g em ei ne M o dul e) /Üb er sc hr i ft en f ür all e S eri en/ G erät e bes c hr ei b ung/ An z eig e el em e nt e - Ü ber sc hr ift 2 @ 4\mod_1240984390875_21.docx@ 31964@ 2 @ 1
3.3 Display Elements
Pos: 18.2 0 / S er ie 750 ( W AG O-I/ O-SYST EM) /G er ät e be schr eib u ng /A nzei g eel e me nt e/Di g it al a usg a ngs kle mm en /A nz ei geel e ment e 750-05 xx 2D O CO (Agn, C gn) @ 16\mod_1371808897994_21.docx@ 123970 @ @ 1
Figure 5: Display Elements
Table 6: Legend for Figure “Display Elements”
Channel
Designation
LED
State
Function
1 State
relays 1 A
Off
Make contact DO 1 opened
Break contact /DO 1 closed
Green
Make contact DO 1 closed
Break contact /DO 1 opened
2 State
relays 2 C
Off
Make contact DO 2 opened
Break contact /DO 2 closed
Green
Make contact DO 2 closed
Break contact /DO 2 opened
Pos: 18.2 1 /D o kum ent ati on al lg em ei n/Gli ed eru ng sel e ment e/---S eit en wec hs el--- @ 3 \mod_1221108045078_0.docx@ 21810@ @ 1

20 Device Description WAGO-I/O-SYSTEM 750
753-514 2DO 125V AC 0.5A/ Relay 2CO/ Potential Free
Manual
Version 1.1.0
Pos: 18.2 2 / Al l e S er ie n ( All g em ei ne M o dul e) /Üb er sc hr i ft en f ür all e S eri en/ G erät e bes c hr ei b ung/ Sc he mati sc h es Schalt bi ld - Über sc hr if t 2 @ 4\mod_1240984441312_21.docx@ 31967@ 2@ 1
3.4 Schematic Diagram
Pos: 18.2 3 / S er ie 753 ( W AG O-I/ O-SYST EM) /G er ät e be schr eib u ng /Sc he m ati s ch es Schal t bil d/Sc h e mat isc hes Sc hal tbil d 753-0514 @ 22\mod_1425566170583_21.docx@ 176981@ @ 1
Figure 6: Schematic Diagram
Pos: 18.2 4 /D o kum ent ati on al lg em ei n/Gli ed eru ng sel e ment e/---S eit en wec hs el--- @ 3 \mod_1221108045078_0.docx@ 21810@ @ 1