WAGO 750-585/040-000 User manual

Pos: 2 /Dokumentation al lgemein/Einband/Ei nband Frontseite - Handbuc h; CI 2017; mitDoc Variablen (Standard) @ 28\mod_148647 7502910_0.docx @ 405388 @ @ 1
Manual
WAGO I/O SYSTEM 750 XTR
750-585/040-000
2AO 0
-20mA Ex i XTR
2
-Channel Analog Output; 0 … 20 mA; Intrinsically
Safe; Extreme
Version 1.1.0
Pos: 3 /Alle Serien (Al lgemeine Module)/Rec htliches, Allgemeines/ Impressum für Standar dhandbücher - allg. Angaben, Ansc hriften, Telefonnummer nund E-Mail-Adr essen @ 3\mod_1219151118203_ 21.docx @ 21060 @ @1

2 WAGO I/O SYSTEM 750 XTR
750-585/040-000 2AO 0-20mA Ex i XTR
Manual
Version 1.1.0
© 2020 WAGO Kontakttechnik GmbH & Co. KG
All rights reserved.
WAGO Kontakttechnik GmbH & Co. KG
Hansastraße 27
D-32423 Minden
Phone: +49 (0) 571/8 87 – 0
Fax: +49 (0) 571/8 87 – 1 69
E-Mail: [email protected]
Web: www.wago.com
Technical Support
Phone: +49 (0) 571/8 87 – 4 45 55
Fax: +49 (0) 571/8 87 – 84 45 55
E-Mail: [email protected]
Every conceivable measure has been taken to ensure the accuracy and
completeness of this documentation. However, as errors can never be fully
excluded, we always appreciate any information or suggestions for improving the
documentation.
E-Mail: [email protected]
We wish to point out that the software and hardware terms as well as the
trademarks of companies used and/or mentioned in the present manual are
generally protected by trademark or patent.
WAGO is a registered trademark of WAGO Verwaltungsgesellschaft mbH.
=== Ende der Liste für Textmarke Einband_vorne = ==

WAGO I/O SYSTEM 750 XTR Table of Contents 3
750-585/040-000 2AO 0-20mA Ex i XTR
Manual
Version 1.1.0
Pos: 5 /Dokumentation al lgemein/Verzeic hnisse/Inhalts verzeichnis - Überschrif t oG und Verzeic hnis @ 3\mod_1219 151230875_21.docx @ 21063 @ @ 1
Table of Contents
1Notes about this Documentation ..............................................................5
1.1 Validity of this Documentation..................................................................5
1.2 Copyright..................................................................................................5
1.3 Symbols ...................................................................................................6
1.4 Number Notation......................................................................................7
1.5 Font Conventions.....................................................................................7
2Important Notes ..........................................................................................8
2.1 Legal Bases .............................................................................................8
2.1.1 Subject to Changes.............................................................................8
2.1.2 Personnel Qualifications......................................................................8
2.1.3Use of the 750 Series in Compliance with Underlying Provisions.......8
2.1.4 Technical Condition of Specified Devices ...........................................9
2.1.4.1 Disposal..........................................................................................9
2.1.4.1.1 Electrical and Electronic Equipment ..........................................9
2.1.4.1.2 Packaging ................................................................................10
2.2 Safety Advice (Precautions)...................................................................11
3Device Description ...................................................................................14
3.1 View .......................................................................................................16
3.2 Connectors.............................................................................................17
3.2.1 Data Contacts/Local Bus...................................................................17
3.2.2 Power Jumper Contacts/Field Supply ...............................................18
3.2.3 CAGE CLAMP®Connectors..............................................................19
3.3 Display Elements ...................................................................................20
3.4 Operating Elements ...............................................................................20
3.5 Schematic Diagram................................................................................21
3.6 Technical Data.......................................................................................22
3.6.1 Device Data.......................................................................................22
3.6.2 Power Supply ....................................................................................22
3.6.3 Outputs..............................................................................................22
3.6.4 Explosion Protection..........................................................................23
3.6.5 Communication .................................................................................23
3.6.6 Connection Type ...............................................................................24
3.6.7 Mechanical Conditions ......................................................................24
3.6.8 Climatic Environmental Conditions....................................................24
3.7 Approvals...............................................................................................25
3.8 Standards and Guidelines......................................................................27
4Process Image ..........................................................................................33
5Mounting ...................................................................................................34
5.1 Mounting Sequence...............................................................................34
5.2 Inserting and Removing Devices ...........................................................36
5.2.1 Inserting the I/O Module....................................................................36
5.2.2 Removing the I/O Module..................................................................37
6Connect Devices.......................................................................................38
6.1 Connecting a Conductor to the CAGE CLAMP®....................................38

4 Table of Contents WAGO I/O SYSTEM 750 XTR
750-585/040-000 2AO 0-20mA Ex i XTR
Manual
Version 1.1.0
6.2 Power Supply Concept ..........................................................................39
6.2.1 Supplementary Power Supply Regulations.......................................42
6.3 Connection Example..............................................................................45
7Use in Hazardous Environments ............................................................46
7.1Marking Configuration Examples ...........................................................47
7.1.1 Marking for Europe According to ATEX and IECEx ..........................47
7.1.2 Marking for the United States of America (NEC) and Canada
(CEC) ................................................................................................51
7.2 Installation Regulations..........................................................................54
7.2.1 Special Notes including Explosion Protection ...................................54
7.2.2 Special Notes Regarding ANSI/ISA Ex .............................................56
List of Figures ....................................................................................................57
List of Tables......................................................................................................58
=== Ende der Liste für Textmarke Verzeichni s_vorne ===

WAGO I/O SYSTEM 750 XTR Notes about this Documentation 5
750-585/040-000 2AO 0-20mA Ex i XTR
Manual
Version 1.1.0
Pos: 7 /Alle Serien (Al lgemeine Module)/Über schriften/Ebene 1/ Hinweise zu dieser Dokumen tation - Überschrif t 1 @ 4\mod_1237987661750_21.d ocx @ 29029 @ 1 @ 1
1 Notes about this Documentation
Pos: 8 /Alle Serien (Al lgemeine Module)/Si cherheits- und sonstige Hin weise/Hinweis/Hin weis: Dokumentation auf bewahren @ 4\mod_12379873 39812_21.docx @ 29026 @ @ 1
Always retain this documentation!
This documentation is part of the product. Therefore, retain the documentation
during the entire service life of the product. Pass on the documentation to any
subsequent user. In addition, ensure that any supplement to this documentation
is included, if necessary.
Pos: 9 /Alle Serien (Al lgemeine Module)/Über schriften/Ebene 2/ Gültigkeitsbereic h - Überschrift 2 @ 12\mod_133 8912448776_21.doc x@ 96469 @ 2 @ 1
1.1 Validity of this Documentation
Pos: 10 /Serie 750 (W AGOI/ OSYS TEM)/Hinweise zur Doku mentation (alte Struk tur)/Gültigkeits bereich/Gültig keitsbereich Doku mentation I/O-Modul 750-xxxx, ohne Var iantenangabe @ 14\mod_1 358944037947_21.doc x@ 1093 46 @ @ 1
This documentation is only applicable to the I/O module 750-585/040-000
(2AO 0-20mA Ex i XTR).
Pos: 11 /Serie 750 (W AGOI/ OSYS TEM)/Hinweise zur Doku mentation (alte Struk tur)/Hinweise/Ac htung: Hinweis zur Doku mentation I/O-Module 750-xxxx/040-000 @ 27\mod_14 68502299549_21.doc x @ 216892 @ @ 1
The I/O module 750-585/040-000 shall only be installed and operated according
to the instructions in this manual, in the system description for the WAGO I/O
SYSTEM 750 XTR and in the manual for the used fieldbus coupler/controller.
Consider power layout of the WAGO I/O SYSTEM 750 XTR!
In addition to these operating instructions, you will also need the system
description “Design Notes XTR – Guidelines and Recommendations for
Increasing Operational Safety” and the manual for the used fieldbus
coupler/controller, which can be downloaded at www.wago.com. There, you can
obtain important information including information on electrical isolation, system
power and supply specifications.
Pos: 12.1 /Alle Serien ( Allgemeine Module)/ Überschriften/Ebene 2/ Urheberschutz - Übersc hrift 2 @ 23\mod_1435647 042188_21.docx @ 184808 @ 2 @ 1
1.2 Copyright
Pos: 12.2 /Alle Serien ( Allgemeine Module)/ Rechtliches, Allge meines/Urheberschut z ausführlich @ 4\mod_123 5565145234_21.doc x@ 27691 @ @ 1
This Manual, including all figures and illustrations, is copyright-protected. Any
further use of this Manual by third parties that violate pertinent copyright
provisions is prohibited. Reproduction, translation, electronic and phototechnical
filing/archiving (e.g., photocopying) as well as any amendments require the
written consent of WAGO Kontakttechnik GmbH & Co. KG, Minden, Germany.
Non-observance will involve the right to assert damage claims.
Pos: 12.3 /Dokumenta tion allgemein/Glied erungselemente/---Sei tenwechsel--- @ 3\mod_122110804 5078_0.docx @ 21810 @ @ 1

6 Notes about this Documentation WAGO I/O SYSTEM 750 XTR
750-585/040-000 2AO 0-20mA Ex i XTR
Manual
Version 1.1.0
Pos: 12.4 /Alle Serien ( Allgemeine Module)/ Überschriften/Ebene 2/ Symbole - Überschrif t 2 @ 13\mod_1351068042408_21. docx @ 105270 @ 2 @ 1
1.3 Symbols
Pos: 12.5.1 /Alle Serien ( Allgemeine Module) /Sicherheits- und sonsti ge Hinweise/Gefahr /Gefahr: _Warnung vor Per sonenschäden allgem ein_ - Erläuterung @ 13\mod_1343 309450020_21.docx @ 101029 @ @ 1
Personal Injury!
Indicates a high-risk, imminently hazardous situation which, if not avoided, will
result in death or serious injury.
Pos: 12.5.2 /Alle Serien ( Allgemeine Module) /Sicherheits- und sonsti ge Hinweise/Gefahr /Gefahr: _Warnung vor Per sonenschäden durc h elektrischen Strom_ - Erläut erung @ 13\mod_134330969 4914_21.docx @ 101030 @ @ 1
Personal Injury Caused by Electric Current!
Indicates a high-risk, imminently hazardous situation which, if not avoided, will
result in death or serious injury.
Pos: 12.5.3 /Alle Serien ( Allgemeine Module) /Sicherheits- und son stige Hinweise/W arnung/Warnung: _Warnung vor Personenschäden a llgemein_ - Erläuterung @ 13\mod_13 43309877041_21.doc x@ 1010 35 @ @ 1
Personal Injury!
Indicates a moderate-risk, potentially hazardous situation which, if not avoided,
could result in death or serious injury.
Pos: 12.5.4 /Alle Serien ( Allgemeine Module) /Sicherheits- und sonsti ge Hinweise/Vorsi cht/Vorsicht: _W arnung vor Personenschäden a llgemein_ - Erläuterung @ 13\mod_1343 310028762_21.doc x@ 101038 @ @ 1
Personal Injury!
Indicates a low-risk, potentially hazardous situation which, if not avoided, may
result in minor or moderate injury.
Pos: 12.5.5 /Alle Serien ( Allgemeine Module) /Sicherheits- und sonsti ge Hinweise/Achtung/ Achtung: _Warnung vor Sachschäden allge mein_ - Erläuterung @ 13\mod_1343 310134623_21.docx @ 101041 @ @ 1
Damage to Property!
Indicates a potentially hazardous situation which, if not avoided, may result in
damage to property.
Pos: 12.5.6 /Alle Serien ( Allgemeine Module) /Sicherheits- und son stige Hinweise/Achtung/ Achtung: _War nung vor Sachschäden durch ele ktrostatische Auflad ung_ - Erläuterung @ 13\mod_1343310 227702_21.docx @ 101044 @ @ 1
Damage to Property Caused by Electrostatic Discharge (ESD)!
Indicates a potentially hazardous situation which, if not avoided, may result in
damage to property.
Pos: 12.5.7 /Alle Serien ( Allgemeine Module) /Sicherheits- und sonsti ge Hinweise/Hinwei s/Hinweis: _Wic htiger Hinweis allgemein_ - Er läuterung @ 13\mod_1343310326 906_21.docx @ 101047 @ @ 1
Important Note!
Indicates a potential malfunction which, if not avoided, however, will not result in
damage to property.
Pos: 12.5.8 /Alle Serien ( Allgemeine Module) /Sicherheits- und sonsti ge Hinweise/Inf ormation/Informatio n: _Weitere Inf ormation allgemein_ - Erläuter ung @ 13\mod_1343310439814_21. docx @ 101051 @ @ 1

WAGO I/O SYSTEM 750 XTR Notes about this Documentation 7
750-585/040-000 2AO 0-20mA Ex i XTR
Manual
Version 1.1.0
Additional Information:
Refers to additional information which is not an integral part of this
documentation (e.g., the Internet).
Pos: 12.6 /Dokumenta tion allgemein/Glied erungselemente/---Sei tenwechsel--- @ 3\mod_122110804 5078_0.docx @ 21810 @ @ 1
Pos: 12.7 /Alle Serien ( Allgemeine Module)/ Überschriften/Ebene 2/ Darstellung der Zahlensysteme - Überschr ift 2 @ 23\mod_1435647128 078_21.docx @ 184811 @ 2 @ 1
1.4 Number Notation
Pos: 12.8 /Alle Serien ( Allgemeine Module)/ Rechtliches, Allge meines/Zahlensyste me@ 3\mo d_1221059454015 _21.docx @ 2171 1 @ @ 1
Table 1: Number Notation
Number Code
Example
Note
Decimal
100
Normal notation
Hexadecimal
0x64
C notation
Binary
'100'
'0110.0100'
In quotation marks, nibble separated
with dots (.)
Pos: 12.9 /Alle Serien ( Allgemeine Module)/ Überschriften/Ebene 2/ Schriftkonventio nen - Überschrift 2 @ 23\mod_1435647186005_21. docx@ 184 814 @ 2 @ 1
1.5 Font Conventions
Pos: 12.10 /Alle Seri en (Allgemeine Module)/ Rechtliches, Allge meines/Schrif tkonventionen @ 3\mod_1221059 521437_21.doc x@ 21714 @ @ 1
Table 2: Font Conventions
Font Type
Indicates
italic
Names of paths and data files are marked in italic-type.
e.g.: C:\Program Files\WAGO Software
Menu
Menu items are marked in bold letters.
e.g.: Save
>
A greater-than sign between two names means the selection of a
menu item from a menu.
e.g.: File > New
Input
Designation of input or optional fields are marked in bold letters,
e.g.:
Start of measurement range
“Value”
Input or selective values are marked in inverted commas.
e.g.: Enter the value “4 mA” under Start of measurement range.
[Button]
Pushbuttons in dialog boxes are marked with bold letters in square
brackets.
e.g.: [Input]
[Key]
Keys are marked with bold letters in square brackets.
e.g.:
[F5]
Pos: 13 /Dokumentation al lgemein/Glieder ungselemente/---Seitenwec hsel--- @ 3\mod_122110804507 8_0.docx @ 21810 @ @ 1

8 Important Notes WAGO I/O SYSTEM 750 XTR
750-585/040-000 2AO 0-20mA Ex i XTR
Manual
Version 1.1.0
Pos: 14 /Alle Serien ( Allgemeine Module)/ Überschriften/Ebene 1/W ichtige Erläuterun gen - Übers chrift 1 @ 4\mod_1241428899156_21.doc x@ 32170 @ 1 @ 1
2 Important Notes
Pos: 15.1 /Alle Serien ( Allgemeine Module)/ Rechtliches, Allge meines/Wichtige Er läuterungen - Einleitung @ 3\mod_1 221059818031_21.doc x@ 21717 @ @ 1
This section includes an overall summary of the most important safety
requirements and notes that are mentioned in each individual section. To protect
your health and prevent damage to devices as well, it is imperative to read and
carefully follow the safety guidelines.
Pos: 15.2 /Alle Serien ( Allgemeine Module)/ Überschriften/Ebene 2/ Rechtliche Grundl agen - Überschrift 2 @ 3\mod_1221060626343_21.d ocx @ 21726 @ 2 @ 1
2.1 Legal Bases
Pos: 15.3 /Alle Serien ( Allgemeine Module)/ Rechtliches, Allge meines/Änderungsvorbe halt - Überschrif t 3 und Inhalt @ 3\mod_122106003 6484_21.docx @ 21720 @ 3 @ 1
2.1.1 Subject to Changes
WAGO Kontakttechnik GmbH & Co. KG reserves the right to provide for any
alterations or modifications. WAGO Kontakttechnik GmbH & Co. KG owns all
rights arising from the granting of patents or from the legal protection of utility
patents. Third-party products are always mentioned without any reference to
patent rights. Thus, the existence of such rights cannot be excluded.
Pos: 15.4 /Serie 750 (W AGOI /O SYSTEM)/Wichti ge Erläuterungen (alte Str uktur)/Personalqua lifikation/Pers onalqualifika tion 750-xxxx - Überschrift 3 und Inhalt @ 3\mod_122406120804 6_21.docx @ 24063 @ 3 @ 1
2.1.2 Personnel Qualifications
All sequences implemented on WAGO I/O SYSTEM 750 devices may only be
carried out by electrical specialists with sufficient knowledge in automation. The
specialists must be familiar with the current norms and guidelines for the devices
and automated environments.
All changes to the coupler or controller should always be carried out by qualified
personnel with sufficient skills in PLC programming.
Pos: 15.5 /Serie 750 (W AGOI /O SYSTEM)/Wichti ge Erläuterungen (alte Str uktur)/Bestimmung sgemäße Verwendung/Bes timmungsgemäße Verwendun g 750-xxxx - Überschrift 3 @ 32\mod_ 1536041141528_21.doc x@ 498 494 @ 3 @ 1
2.1.3 Use of the 750 Series in Compliance with Underlying
Provisions
Pos: 15.6 /Serie 750 (W AGOI /O SYSTEM)/Wichti ge Erläuterungen (alte Str uktur)/Bestimmung sgemäße Verwendung/Bes timmungsgemäße Verwendun g 750-xxxx für Geräte - STD - mit E N 61000-6-3 @ 3\mod_122406415 1234_21.docx @ 24070 @ @ 1
Fieldbus couplers, controllers and I/O modules found in the modular WAGO I/O
SYSTEM 750 receive digital and analog signals from sensors and transmit them
to actuators or higher-level control systems. Using controllers, the signals can
also be (pre-) processed.
The devices have been developed for use in an environment that meets the IP20
protection class criteria. Protection against finger injury and solid impurities up to
12.5 mm diameter is assured; protection against water damage is not ensured.
Unless otherwise specified, operation of the devices in wet and dusty
environments is prohibited.
Operating the WAGO I/O SYSTEM 750 devices in home applications without
further measures is only permitted if they meet the emission limits (emissions of
interference) according to EN 61000-6-3. You will find the relevant information in
the section “Device Description” > “Standards and Guidelines” in the manual for
the used fieldbus coupler or controller.

WAGO I/O SYSTEM 750 XTR Important Notes 9
750-585/040-000 2AO 0-20mA Ex i XTR
Manual
Version 1.1.0
Appropriate housing (per 2014/34/EU) is required when operating the WAGO I/O
SYSTEM 750 in hazardous environments. Please note that a prototype test
certificate must be obtained that confirms the correct installation of the system in
a housing or switch cabinet.
The implementation of safety functions such as EMERGENCY STOP or safety
door monitoring must only be performed by the F I/O modules within the modular
WAGO I/O SYSTEM 750. Only these safe F I/O modules ensure functional safety
in accordance with the latest international standards. WAGO's interference-free
output modules can be controlled by the safety function.
Pos: 15.7 /Alle Serien ( Allgemeine Module)/ Rechtliches, Allge meines/Technischer Zustand der Geräte - Übersc hrift 3 und Inhalt @ 3\mod_ 1221060446109_21.doc x @ 21723 @ 3 @ 1
2.1.4 Technical Condition of Specified Devices
The devices to be supplied ex works are equipped with hardware and software
configurations, which meet the individual application requirements. These
modules contain no parts that can be serviced or repaired by the user. The
following actions will result in the exclusion of liability on the part of WAGO
Kontakttechnik GmbH & Co. KG:
• Repairs,
• Changes to the hardware or software that are not described in the
operating instructions,
• Improper use of the components.
Further details are given in the contractual agreements. Please send your
request for modified and new hardware or software configurations directly to
WAGO Kontakttechnik GmbH & Co. KG.
Pos: 15.8 /Alle Serien ( Allgemeine Module)/ Überschriften/Ebene 4/ Entsorgen - Überschri ft 4 @ 30\mod_151014511565 2_21.docx @ 469859 @ 4 @ 1
2.1.4.1 Disposal
Pos: 15.9.1 /Alle Serien ( Allgemeine Module) /Überschriften/ Ebene 5/Elektro- und Elektroni kgeräte - Überschri ft 5 @ 32\mod_1537446988 068_21.docx @ 501657 @ 5 @ 1
2.1.4.1.1 Electrical and Electronic Equipment
Pos: 15.9.2 /Alle Serien ( Allgemeine Module) /Rechtliches, Allg emeines/Elektro- und Elek tronikgeräte @ 32\mod_1 532425086061_21.doc x @ 491989 @ @ 1
Electrical and electronic equipment may not be disposed of
with household waste. This also applies to products without
this symbol.
Electrical and electronic equipment contain materials and substances that can be
harmful to the environment and health. Electrical and electronic equipment must
be disposed of properly after use.
WEEE 2012/19/EU applies throughout Europe. Directives and laws may vary
nationally.

10 Important Notes WAGO I/O SYSTEM 750 XTR
750-585/040-000 2AO 0-20mA Ex i XTR
Manual
Version 1.1.0
Environmentally friendly disposal benefits health and protects
the environment from harmful substances in electrical and
electronic equipment.
• Observe national and local regulations for the disposal of electrical and
electronic equipment.
• Clear any data stored on the electrical and electronic equipment.
• Remove any added battery or memory card in the electrical and
electronic equipment.
• Have the electrical and electronic equipment sent to your local
collection point.
Improper disposal of electrical and electronic equipment can be harmful to the
environment and human health.
Pos: 15.9.3 /Dokumen tation allgemein/Gli ederungselemente/ ----Leerzeile-(1Z) ---- @ 28\mod_1485262995837_0.doc x@ 404 006@ @ 1
Pos: 15.9.4 /Alle Serien ( Allgemeine Module) /Überschriften/ Ebene 5/Verpackung - Überschr ift 5 @ 32\mod_153744704 4202_21.docx @ 501662 @ 5 @ 1
2.1.4.1.2 Packaging
Pos: 15.9.5 /Alle Serien ( Allgemeine Module) /Rechtliches, Allg emeines/Verpackung @ 32\mod_153744678641 6_21.docx @ 501653 @ @ 1
Packaging contains materials that can be reused.
PPWD 94/62/EU and 2004/12/EU packaging guidelines apply throughout
Europe. Directives and laws may vary nationally.
Environmentally friendly disposal of the packaging protects the environment and
allows sustainable and efficient use of resources.
• Observe national and local regulations for the disposal of packaging.
• Dispose of packaging of all types that allows a high level of recovery,
reuse and recycling.
Improper disposal of packaging can be harmful to the environment and wastes
valuable resources.
Pos: 15.10 /Dokumenta tion allgemein/Glie derungselemente/---Sei tenwechsel--- @ 3\mod_1221108045078_0. docx @ 21810 @ @ 1

WAGO I/O SYSTEM 750 XTR Important Notes 11
750-585/040-000 2AO 0-20mA Ex i XTR
Manual
Version 1.1.0
Pos: 15.11 /Alle Seri en (Allgemeine Module)/ Überschriften/Eben e 2/Sicherheitshi nweise - Überschrif t 2 @ 6\mod_1260180299987_21. docx @ 46724 @ 2 @ 1
2.2 Safety Advice (Precautions)
Pos: 15.12 /Alle Serien ( Allgemeine Module)/Si cherheits- und sonstige Hin weise/Einleitu ng Sicherheitshinwei se Hardware @ 6\mod_126018017 0493_21.docx @ 46720 @ @ 1
For installing and operating purposes of the relevant device to your system the
following safety precautions shall be observed:
Pos: 15.13.1 /Alle Ser ien (Allgemeine Module) /Sicherheits- und sonsti ge Hinweise/Gefahr /Gefahr: Nicht an Gerä tenu nter Spannung arbei ten! @ 6\mod_1260180365327 _21.docx @ 46727 @ @ 1
Do not work on devices while energized!
All power sources to the device shall be switched off prior to performing any
installation, repair or maintenance work.
Pos: 15.13.2 /Alle Ser ien (Allgemeine Module) /Sicherheits- und sonsti ge Hinweise/Gefahr /Gefahr: Produkt nur in einem geeigneten Gehäuse einbauen! @ 33\mod_154 3581881435_21.doc x @ 511972 @ @ 1
Install device in only one suitable enclosure!
The device is an open system. Install the device in a suitable enclosure. This
enclosure must:
• Guarantee that the max. permissible degree of pollution is not exceeded.
• Offer adequate protection against contact.
• Prevent fire from spreading outside of the enclosure.
• Offer adequate protection against UV irradiation.
• Guarantee mechanical stability
• Restrict access to authorized personnel and may only be opened with tools
Pos: 15.13.3 /Alle Ser ien (Allgemeine Module) /Sicherheits- und sonsti ge Hinweise/Gefahr /Gefahr: Trennvorr ichtung und Überstrom schutz @ 33\mod_15439159784 39_21.docx @ 512267 @ @ 1
Ensure disconnect and overcurrent protection!
The device is intended for installation in automation technology systems.
Disconnect protection is not integrated. Connected systems must be protected by
a fuse.
Provide suitable disconnect and overcurrent protection on the system side!
Pos: 15.13.4 /Alle Ser ien (Allgemeine Module) /Sicherheits- und sonsti ge Hinweise/Gefahr /Gefahr: Unfallver hütungsvorschri ften beachten! @ 6\mod_12601806 57000_21.docx @ 46735 @ @ 1
Pos: 15.13.5 /Alle Ser ien (Allgemeine Module) /Sicherheits- und sonsti ge Hinweise/Gefahr /Gefahr: Auf normgerechten Ansch luss achten! @ 6\mod_1260180753479_21.d ocx @ 46739 @ @ 1
Ensure a standard connection!
To minimize any hazardous situations resulting in personal injury or to avoid
failures in your system, the data and power supply lines shall be installed
according to standards, with careful attention given to ensuring the correct
terminal assignment. Always adhere to the EMC directives applicable to your
application.
Pos: 15.14 /Serie 750 (W AGOI /O SYSTEM)/Wichti ge Erläuterungen (alte Str uktur)/Sicher heits- und sonstige Hinweise/ Warnung/War nung: Speisung ausschließ lich aus SELV-/PELV-Versorgung (24V -XTR-I/O-Module) @ 29\mod_1493107132163_21. docx @ 419618 @ @ 1
Power from SELV/PELV power supply only!
All field signals and field supplies connected to this XTR I/O module
(750-585/040-000) must be powered from SELV/PELV power supply(s)!
Pos: 15.15 /Alle Seri en (Allgemeine Module)/ Sicherheits- und sons tige Hinweise/Vorsic ht/Vorsicht: Heiße Ob erfläche nicht berühr en! (allgemein) @ 6\mod_126 4428115588_21.doc x@ 48610 @ @ 1

12 Important Notes WAGO I/O SYSTEM 750 XTR
750-585/040-000 2AO 0-20mA Ex i XTR
Manual
Version 1.1.0
Do not touch hot surfaces!
The surface of the housing can become hot during operation. If the device was
operated at high ambient temperatures, allow it to cool off before touching it.
Pos: 15.16.1 /Seri e 750 (WAGO I/O SYSTEM)/Wic htige Erläuterungen (alt e Struktur)/Sic herheits- und sonstige Hin weise/Achtung/Achtun g: Einwandfreie Kon taktierung zur Tragschi ene gewährleisten! @ 34\mod_15504814 07638_21.doc x @ 530599 @ @ 1
Ensure proper contact with the DIN-rail!
Proper electrical contact between the DIN-rail and device is necessary to
maintain the EMC characteristics and function of the device.
Pos: 15.16.2 /Alle Ser ien (Allgemeine Module)/Si cherheits- und sonstige Hin weise/Achtung/Ac htung: Defekte oder besc hädigte Geräte austausc hen! @ 6\mod_126018085735 8_21.docx @ 46743 @ @ 1
Replace defective or damaged devices!
Replace defective or damaged device/module (e.g., in the event of deformed
contacts).
Pos: 15.16.3 /Alle Ser ien (Allgemeine Module) /Sicherheits- und sonsti ge Hinweise/Achtun g/Achtung: Geräte vor kriechenden und iso lierenden Stoffen schü tzen! @ 6\mod_1260181036216 _21.docx @ 46747 @ @ 1
Protect the components against materials having seeping and insulating
properties!
The components are not resistant to materials having seeping and insulating
properties such as: aerosols, silicones and triglycerides (found in some hand
creams). If you cannot exclude that such materials will appear in the component
environment, then install the components in an enclosure being resistant to the
above-mentioned materials. Clean tools and materials are imperative for
handling devices/modules.
Pos: 15.16.4 /Alle Ser ien (Allgemeine Module)/Si cherheits- und sonstige Hin weise/Achtung/Ac htung: Reinigung nur mit zul ässigen Materialien! @ 6\mod_1260181203293_2 1.docx @ 46751 @ @ 1
Clean only with permitted materials!
Clean housing and soiled contacts with propanol.
Pos: 15.16.5 /Alle Seri en (Allgemeine Module)/ Sicherheits- und sonstig e Hinweise/Achtung/ Achtung: Kein Kontakt spray verwenden! @ 6\mod_126 0181290808_21.doc x@ 46755 @ @ 1
Do not use any contact spray!
Do not use any contact spray. The spray may impair contact area functionality in
connection with contamination.
Pos: 15.16.6 /Alle Ser ien (Allgemeine Module) /Sicherheits- und sonsti ge Hinweise/Achtun g/Achtung: Verpolun gen der Daten- und Versorgungs leitungen vermeiden! @ 6\mod_1260184045744_ 21.docx @ 46767 @ @ 1
Do not reverse the polarity of connection lines!
Avoid reverse polarity of data and power supply lines, as this may damage the
devices involved.
Pos: 15.16.7 /Alle Ser ien (Allgemeine Module) /Sicherheits- und sonsti ge Hinweise/Achtun g/Achtung: Elektr ostatische Entladung vermeiden! - DI N EN 6134 0-5-1/-3 @ 6\mod_1260181364729_21. docx @ 46759 @ @ 1

WAGO I/O SYSTEM 750 XTR Important Notes 13
750-585/040-000 2AO 0-20mA Ex i XTR
Manual
Version 1.1.0
Avoid electrostatic discharge!
The devices are equipped with electronic components that may be destroyed by
electrostatic discharge when touched. Please observe the safety precautions
against electrostatic discharge per DIN EN 61340-5-1/-3. When handling the
devices, please ensure that environmental factors (personnel, work space and
packaging) are properly grounded.
Pos: 15.17 /Serie 750 (W AGOI /O SYSTEM)/Wichti ge Erläuterungen (alte Str uktur)/Sicher heits- und sonstige Hin weise/Achtung/Ac htung: XTR - Isola tionsprüfungen mit DC durchführen! @ 15\mod_1370843209441_2 1.docx @ 122210 @ @ 1
Use only direct current (DC) for insulation testing!
Both the system voltage and field voltage side are capacitively coupled to the
DIN-rail. If an I/O module is mounted on the DIN-rail, application of an AC voltage
between the DIN-rail and at least one of these two potentials can lead to the
destruction of the module.
Use only direct current (DC) for insulation testing. To avoid destroying the I/O
module, you must discharge it completely before applying the test voltage again.
Pos: 16 /Dokumentation al lgemein/Glieder ungselemente/---Seitenwec hsel--- @ 3\mod_122110804507 8_0.docx @ 21810 @ @ 1

14 Device Description WAGO I/O SYSTEM 750 XTR
750-585/040-000 2AO 0-20mA Ex i XTR
Manual
Version 1.1.0
Pos: 17 /Alle Serien ( Allgemeine Module)/ Überschriften/Ebene 1/ Gerätebeschreibung - Übersc hrift 1 @ 3\mod_12337 56084656_21.doc x@ 27096 @ 1 @ 1
3 Device Description
Pos: 18.1.1 /Seri e 750 (WAGO I/O SYSTEM)/Geräteb eschreibung (alte Str uktur)/Einleitung/ Anwendung/AO/An wendung 750-05xx AO E x i Zone 1 (0...20mA) @ 12\mod_1337840585706_21.doc x @ 95483 @ @ 1
The analog output module 750-585/040-000 (2AO 0-20mA Ex i XTR) generates a
standardized signal of 0 … 20 mA for hazardous field area of zone 0 or 1.
Pos: 18.1.2 /Seri e 750 (WAGO I/O SYSTEM)/Wic htige Erläuterungen (alte S truktur)/Sic herheits- und sonstige Hinwei se/Warnung/W arnung: Exi Installation des W AGO-I/O-SYSTEM750 nur in Zone 2 oder im nicht-ex-Bereich @ 5\mod_1245851655116_21. docx @ 35947 @ @ 1
Installation only in zone 2 or in non-hazardous environments!
The installation of the WAGO I/O SYSTEM 750 fieldbus couplers/controllers and
I/O modules is only to be done in zone 2 or in non-hazardous environments.
Pos: 18.1.3 /Seri e 750 (WAGO I/O SYSTEM)/Geräteb eschreibung (alte Str uktur)/Einleitung/ I/O-Beschreibung/ AO/I/O-Beschreibung 750-05xx 2 AO 2-Leiter ( AO und 0V) @ 5\mod_1247048703 979_21.docx @ 36857 @ @ 1
The module has 2 output channels and enables, for example, the direct wiring of
two 2-conductor actuators. The actuators are connected to the CAGE CLAMP®
connectors AO 1 and 0 V or AO 2 and 0 V.
Pos: 18.1.4 /Seri e 750 (WAGO I/O SYSTEM)/Geräteb eschreibung (alte Str uktur)/Einleitung/ LED-Anzeige/LED Zust and Betrieb Kanal @ 5\mod_124539 1732046_21.doc x@ 35668 @ @ 1
The operating status of the channels is indicated by a green status LED per
channel.
Pos: 18.1.5 /Seri e 750 (WAGO I/O SYSTEM)/Geräteb eschreibung (alte Str uktur)/Einleitung/ LED-Anzeige/Verweis auf Kapitel "Anzei geelemente" @ 5\mod_1 246010525000_21.doc x @ 36194 @ @ 1
The meaning of the LEDs is described in the “Display Elements” section.
Pos: 18.1.6 /Seri e 750 (WAGO I/O SYSTEM)/Geräteb eschreibung (alte Str uktur)/Einleitung/ Versorgung/Versor gung 24 V, 0 V über Leistungsko ntakte Ex i XTR - NEUE FORMULIERUNG @ 28\mod_1486 132138923_21.doc x@ 405 256@ @ 1
The Ex i XTR I/O module (750-585/040-000) receives the 24 V voltage supply
potential and the 0V potential for the field level from an upstream Ex i XTR I/O
module or from the “Power Supply 24 VDC Diagn for Ex i XTR Modules” 750-
606/040-000 via the power contacts designed as blade contacts.
The Ex i XTR I/O module (750-585/040-000) provides these potentials to
subsequent I/O modules via the power contacts designed as spring contacts.
Pos: 18.1.7 /Seri e 750 (WAGO I/O SYSTEM)/Wic htige Erläuterungen (alte S truktur)/Sic herheits- und sonstige Hinwei se/Warnung/W arnung: Exi Einspeisung nur mit 75 0-606 XTR @ 28\mod_14861 31251915_21.docx @ 405250 @ @ 1
Ex i XTR I/O modules shall only be supplied via “Power Supply 24 VDC
Diagn for Ex i XTR Modules”
Ex i XTR I/O modules shall only be operated with a “Power Supply 24 VDC
Diagn for Ex i XTR Modules” 750-606/040-000.
Pos: 18.1.8 /Seri e 750 (WAGO I/O SYSTEM)/Wic htige Erläuterungen (alte S truktur)/Sic herheits- und sonstige Hinwei se/Achtung/Achtung: Maximaler Stro mE xi Einspeisung 750-0606/040-00 0 XTR @ 28\mod_ 1486128985806_21.doc x@ 405 244 @ @ 1
Do not exceed maximum current via power contacts!
The maximum current available from the “Power Supply 24 VDC Diagn for Ex i
XTR Modules” 750-606/040-000 is 1 A.
When configuring the system, ensure that this current is not exceeded.
If exceeded, an additional 750-606/040-000 must be used.
Pos: 18.1.9 /Seri e 750 (WAGO I/O SYSTEM)/Geräteb eschreibung (alte Str uktur)/Einleitung/ Versorgung/Gal vanische Trennung Feld/ System @ 3\mod_1233756478 750_21.docx @ 27102 @ @ 1
The field voltage and the system voltage are electrically isolated from each other.
Pos: 18.1.10 /Seri e 750 (WAGO I/O SYSTEM)/Geräte beschreibung (alte Str uktur)/Einleitun g/I/O-Beschreibung/ AO/I/O-Beschrei bung 750-05xx AO Gemeins amer Schi rmanschluss @ 12\mod_133 7841659376_21.doc x @ 95495@ @ 1
The output channels of this module have a common shield (screen) connection.
Pos: 18.1.11 /Seri e 750 (WAGO I/O SYSTEM)/Geräte beschreibung (alte Str uktur)/Einleitun g/I/O-Beschreibung/ Allgemein/Verwei s auf Kapitel "An schlüsse" @ 8\mod_127677 5378035_21.doc x@ 57956 @ @ 1
The assignment of the connections is described in the “Connectors” section.
Pos: 18.1.12 /Seri e 750 (WAGO I/O SYSTEM)/Geräte beschreibung (alte Str uktur)/Einleitun g/I/O-Beschreibung/ Allgemein/Verweis auf Kap itel "Geräte anschließen" > "Ansc hlussbeispiel(e) " @ 5\mod_1246015203281_21.doc x @ 36298 @ @ 1
Connection examples are shown in section “Connect Devices” > … >
“Connection Example(s)”.
Pos: 18.1.13 /Seri e 750 (WAGO I/O SYSTEM)/Geräte beschreibung (alte Str uktur)/Einleitun g/Versorgung/Anor dnung in Ex i-Segment belie big @ 4\mod_124150660020 3_21.docx @ 32297 @ @ 1

WAGO I/O SYSTEM 750 XTR Device Description 15
750-585/040-000 2AO 0-20mA Ex i XTR
Manual
Version 1.1.0
Any configuration of the I/O module is possible within an intrinsically safe
segment when configuring the fieldbus node. An arrangement in groups within
the group of potentials is not necessary.
Pos: 18.1.14 /Seri e 750 (WAGO I/O SYSTEM)/Geräte beschreibung (alte Str uktur)/Einleitun g/Einsatzberei ch/Einsatzbereic h 750-xxxx/040-000 alle XTR-Koppler /Controller ohne Einsc hränkung+Mischbetr iebhinweise @ 15\mod_13684 25919479_21.doc x@ 1194 44@ @ 1
The I/O module can be operated with all fieldbus couplers/controllers of the
WAGO I/O SYSTEM 750 XTR.
Observe the instructions for mixed operation when used in mixed operation
behind standard fieldbus couplers/controllers.
Pos: 18.2 /Dokumenta tion allgemein/Glied erungselemente/---Sei tenwechsel--- @ 3\mod_122110804 5078_0.docx @ 21810 @ @ 1

16 Device Description WAGO I/O SYSTEM 750 XTR
750-585/040-000 2AO 0-20mA Ex i XTR
Manual
Version 1.1.0
Pos: 18.3 /Alle Serien ( Allgemeine Module)/ Überschriften/Ebene 2/ Ansicht - Überschri ft 2 @ 4\mod_1240984217343_ 21.docx @ 31958 @ 2 @ 1
3.1 View
Pos: 18.4 /Serie 750 (W AGOI /O SYSTEM)/Gerätebesc hreibung (alte Strukt ur)/Ansicht/AO/A nsicht 750-0585/040-000 @ 28\mod_14 87756987944_21. docx @ 408856 @ @ 1
Figure 1: View
Pos: 18.5 /Serie 750 (W AGOI /O SYSTEM)/Gerätebesc hreibung (alte Strukt ur)/Ansicht/Ansi cht CageClamp®_Legende mit LEDs, mit 1 Entri egelungslasche @ 15\mod_137086 7188922_21.doc x@ 12222 5@ @ 1
Table 3: Legend for Figure “View”
Pos.
Description
Details See Section
1
Marking possibility with Mini-
WSB
---
2
Status LEDs
“Device Description” > “Display Elements”
3
Data contacts
“Device Description” > “Connectors”
4
CAGE CLAMP®connectors
“Device Description” > “Connectors”
5
Power jumper contacts
“Device Description” > “Connectors”
6
Release tab
“Mounting” > “Inserting and Removing
Devices”
Pos: 18.6 /Dokumenta tion allgemein/Glied erungselemente/---Sei tenwechsel--- @ 3\mod_1221108045078 _0.docx @ 21810 @ @ 1

WAGO I/O SYSTEM 750 XTR Device Description 17
750-585/040-000 2AO 0-20mA Ex i XTR
Manual
Version 1.1.0
Pos: 18.7 /Alle Serien ( Allgemeine Module)/ Überschriften/Ebene 2/ Anschlüsse - Überschri ft 2 @ 4\mod_124098426265 6_21.docx @ 31961 @ 2 @ 1
3.2 Connectors
Pos: 18.8 /Serie 750 (W AGOI /O SYSTEM)/Gerätebesc hreibung (alte Strukt ur)/Anschlüsse/ Datenkontakte/Loka lbus - Überschrift 3 @ 6\mod_12 56294684083_21.doc x@ 43660 @ 3 @ 1
3.2.1 Data Contacts/Local Bus
Pos: 18.9.1 /Seri e 750 (WAGO I/O SYSTEM)/Geräteb eschreibung (alte Str uktur)/Anschlüss e/Datenkontakte - Feldbusko ppler/-controll er und Module – Abbildung und Besc hreibung @ 3\mod_12317712 59187_21.docx @ 26002 @ @ 1
Communication between the fieldbus coupler/controller and the I/O modules as
well as the system supply of the I/O modules is carried out via the local bus. The
contacting for the local bus consists of 6 data contacts, which are available as
self-cleaning gold spring contacts.
Figure 2: Data Contacts
Pos: 18.9.2 /Seri e 750 (WAGO I/O SYSTEM)/Wic htige Erläuterungen (alte S truktur)/Sic herheits- und sonstige Hinwei se/Achtung/Achtung: I/ O-Modulenicht auf Goldfederkont akte legen! @ 7\mod_1266318463 636_21.docx @ 50695 @ @ 1
Do not place the I/O modules on the gold spring contacts!
Do not place the I/O modules on the gold spring contacts in order to avoid soiling
or scratching!
Pos: 18.9.3 /Seri e 750 (WAGO I/O SYSTEM)/Wic htige Erläuterungen (alte S truktur)/Sic herheits- und sonstige Hinwei se/Achtung/Achtung: ESD - Auf Potentialausgl eich der Umgebung achte n! @ 32\mod_1539077262331_2 1.docx @ 504433 @ @ 1
Pay attention to potential equalization from the environment!
The devices are equipped with electronic components that may be destroyed by
electrostatic discharge. When handling the devices, please ensure that
environmental factors (personnel, work space and packaging) are properly
equalized. Do not touch any conducting parts, e.g., data contacts.
Pos: 18.10 /Dokumenta tion allgemein/Glie derungselemente/---Sei tenwechsel--- @ 3\mod_1221108045078_0. docx @ 21810 @ @ 1

18 Device Description WAGO I/O SYSTEM 750 XTR
750-585/040-000 2AO 0-20mA Ex i XTR
Manual
Version 1.1.0
Pos: 18.11 /Serie 750 (W AGOI /O SYSTEM)/Gerätebesc hreibung (alte Struk tur)/Anschlüsse/ Leistungskontak te/Feldversorgung - Übersc hrift 3 @ 6\mod_125629 4692864_21.doc x@ 43664 @ 3 @ 1
3.2.2 Power Jumper Contacts/Field Supply
Pos: 18.12.1 /Seri e 750 (WAGO I/O SYSTEM)/Wic htige Erläuterungen (alt e Struktur)/Sic herheits- und sonstige Hin weise/Vorsicht/Vorsi cht: Verletzungs gefahr durch schar fkantige Messerkontakte! @ 6\mod_1256193279401_2 1.docx @ 43414 @ @ 1
Risk of injury due to sharp-edged blade contacts!
The blade contacts are sharp-edged. Handle the I/O module carefully to prevent
injury. Do not touch the blade contacts.
Pos: 18.12.2 /Seri e 750 (WAGO I/O SYSTEM)/Geräte beschreibung (alte Str uktur)/Anschlüs se/Leistungskontakt e 2 LK (Messer/Feder) - Einleitung @ 15\mod_13717216410 99_21.docx @ 123714 @ @ 1
The I/O module 750-585/040-000 has 2 self-cleaning power jumper contacts that
supply and transmit power for the field side. The contacts on the left side of the
I/O module are designed as blade contacts and those on the right side as spring
contacts.
Pos: 18.12.3 /Seri e 750 (WAGO I/O SYSTEM)/Geräte beschreibung (alte Str uktur)/Anschlüs se/Leistungskontakt e 2 LK (Messer/Feder) - Abbildung, doppelte Breite, Ex i @ 30\mod_15084285922 12_21.docx @ 467258 @ @ 1
Figure 3: Power Jumper Contacts
Pos: 18.12.4 /Seri e 750 (WAGO I/O SYSTEM)/Geräte beschreibung (alte Str uktur)/Anschlüs se/Leistungskontakt e 2 LK (Messer/Feder) - Legende @ 15\mod_1371721352500_ 21.docx @ 123710 @ @ 1
Table 4: Legend for Figure “Power Jumper Contacts”
Contact
Type
Function
1
Spring contact
Potential transmission (Uv) for field supply
2
Spring contact
Potential transmission (0 V) for field supply
3
Blade contact
Potential feed-in (0 V) for field supply
4
Blade contact
Potential feed-in (Uv) for field supply
Pos: 18.12.5 /Seri e 750 (WAGO I/O SYSTEM)/Wic htige Erläuterungen (alt e Struktur)/Sic herheits- und sonstige Hin weise/Achtung/Achtun g: Maximaler Strom Ex i Ei nspeisung 750-0606/040-000 XTR @ 28\mod_14861289858 06_21.docx @ 405244 @ @ 1
Do not exceed maximum current via power contacts!
The maximum current available from the “Power Supply 24 VDC Diagn for Ex i
XTR Modules” 750-606/040-000 is 1 A.
When configuring the system, ensure that this current is not exceeded.
If exceeded, an additional 750-606/040-000 must be used.
Pos: 18.13 /Dokumenta tion allgemein/Glie derungselemente/---Sei tenwechsel--- @ 3\mod_1221108045078_0. docx @ 21810 @ @ 1

WAGO I/O SYSTEM 750 XTR Device Description 19
750-585/040-000 2AO 0-20mA Ex i XTR
Manual
Version 1.1.0
Pos: 18.14 /Serie 750 (W AGOI /O SYSTEM)/Gerätebesc hreibung (alte Struk tur)/Anschlüsse/ CAGE CLAMP-Anschlüsse - Übersc hrift 3 @ 6\mod_125 6296337770_21.doc x @ 43674@ 3 @ 1
3.2.3 CAGE CLAMP®Connectors
Pos: 18.15 /Serie 750 (W AGOI /O SYSTEM)/Gerätebesc hreibung (alte Struk tur)/Anschlüsse/ AO/Anschlüsse 750-0585/ 040-000 @ 28\mod_1487757049286_2 1.docx @ 408859 @ @ 1
Figure 4: CAGE CLAMP®Connectors
Table 5: Legend for Figure “CAGE CLAMP®Connector”
Channel
Designation
Connector
Function
1
AO 1
1
Output AO 1: Signal voltage
0 V
3
Output AO 1: Actuator supply 0 V
2
AO 2
5
Output AO 2: Signal voltage
0 V
7
Output AO 2: Actuator supply 0 V
-
S
4
Shield connection
S
8
Pos: 18.16 /Serie 750 (W AGOI /O SYSTEM)/Wichti ge Erläuterungen (alte Str uktur)/Sicher heits- und sonstige Hinweise/ Hinweis/Hinweis: Ge schirmte Signalleit ungen verwenden! @ 7\mod_1265 723251019_21.doc x@ 50140 @ @ 1
Use shielded signal lines!
Only use shielded signal lines for analog signals and I/O modules which are
equipped with shield clamps. Only then can you ensure that the accuracy and
interference immunity specified for the respective I/O module can be achieved
even in the presence of interference acting on the signal cable.
Pos: 18.17 /Dokumenta tion allgemein/Glie derungselemente/---Sei tenwechsel--- @ 3\mod_1221108045078_0. docx @ 21810 @ @ 1

20 Device Description WAGO I/O SYSTEM 750 XTR
750-585/040-000 2AO 0-20mA Ex i XTR
Manual
Version 1.1.0
Pos: 18.18 /Alle Seri en (Allgemeine Module)/ Überschriften/Eben e 2/Anzeigeelemen te- Übersc hrift 2 @ 4\mod_12409 84390875_21.doc x @ 31964 @ 2 @ 1
3.3 Display Elements
Pos: 18.19 /Serie 750 (W AGOI /O SYSTEM)/Gerätebesc hreibung (alte Struk tur)/Anzeigeele mente/AO/Anzeigeele mente 750-0585/040-000 @ 28\mod_1487 695598237_21.doc x@ 408 777@ @ 1
Figure 5: Display Elements
Table 6: Legend for Figure “Display Elements”
Channel
Designation
LED
State
Function
1 Status AO 1 A
Off
No operational readiness or the local
bus communication is interrupted
Green
Operational readiness and trouble-free
local bus communication
2 Status AO 2 E
Off
No operational readiness or the local
bus communication is interrupted
Green
Operational readiness and trouble-free
local bus communication
Pos: 18.20 /Alle Seri en (Allgemeine Module)/ Überschriften/Eben e 2/Bedienelemente - Übersc hrift 2 @ 4\mod_1239191 655456_21.doc x@ 30439 @ 2 @ 1
3.4 Operating Elements
Pos: 18.21 /Serie 750 (W AGOI /O SYSTEM)/Gerätebesc hreibung (alte Struk tur)/Bedienele mente/Bedienelemente I /O-Modul 75x-xxxx nicht vorhanden @ 4\mod_123632203112 5_21.docx @ 28063 @ @ 1
The I/O module 750-585/040-000 has no operating elements.
Pos: 18.22 /Dokumenta tion allgemein/Glie derungselemente/---Sei tenwechsel--- @ 3\mod_1221108045078_0. docx @ 21810 @ @ 1
Table of contents
Other WAGO Control Unit manuals

WAGO
WAGO I/O-SYSTEM 750 User manual

WAGO
WAGO 750-652/040-000 User manual

WAGO
WAGO 750-555 User manual

WAGO
WAGO I/O-SYSTEM 751-3001 User manual

WAGO
WAGO WAGO-TO-PASS 761 User manual

WAGO
WAGO 750-491 User manual

WAGO
WAGO 750-502 User manual

WAGO
WAGO 750-563/040-000 User manual

WAGO
WAGO 750-645 User manual

WAGO
WAGO 750-363/0040-0000 User manual

WAGO
WAGO 750-535 User manual

WAGO
WAGO WAGO-TO-PASS 761 User manual

WAGO
WAGO 750-494 Series User manual

WAGO
WAGO 750-606 User manual

WAGO
WAGO 750-535/040-000 User manual

WAGO
WAGO 767-1501 User manual

WAGO
WAGO 767-4802/000-800 User manual

WAGO
WAGO TECHDOCS 750-600/000-001 User manual

WAGO
WAGO SPEEDWAY 767 Series User manual

WAGO
WAGO WAGO-TO-PASS 761 User manual