WAGO I/O-SYSTEM 750 User manual

Pos: 2 /Dokumentation al lgemein/Einband/Ei nband Handbuch - Frontseit e 2015 - mit DocVariablen ( Standard) @ 9\mod_12852292 89866_0.docx @ 64941 @ @ 1
WAGO-I/O-SYSTEM 750
Manual
750-597
8AO 0-
10V/±10V DC
8-Ch
annel Analog Output Module 0 ... 10 V/±10 V
Version 1.0.0
Pos: 3 /Alle Serien (Al lgemeine Module)/Rec htliches, Allgemeines/ Impressum für Standar dhandbücher - allg. Angaben, Ansc hriften, Telefonnummer nund E-Mail-Adr essen @ 3\mod_1219151118203_ 21.docx @ 21060 @ @1

2 WAGO-I/O-SYSTEM 750
750-597 8AO 0-10V/±10V DC
Manual
Version 1.0.0
© 2016 by WAGO Kontakttechnik GmbH & Co. KG
All rights reserved.
WAGO Kontakttechnik GmbH & Co. KG
Hansastraße 27
D-32423 Minden
Phone: [phone] – 0
Fax: [phone] – 1 69
E-Mail: [email protected]
Web: http://www.wago.com
Technical Support
Phone: [phone] – 5 55
Fax: [phone] – 85 55
E-Mail: [email protected]
Every conceivable measure has been taken to ensure the accuracy and
completeness of this documentation. However, as errors can never be fully
excluded, we always appreciate any information or suggestions for improving the
documentation.
E-Mail: [email protected]
We wish to point out that the software and hardware terms as well as the
trademarks of companies used and/or mentioned in the present manual are
generally protected by trademark or patent.
=== Ende der Liste für Textmarke Einband_vorne = ==

WAGO-I/O-SYSTEM 750 Table of Contents 3
750-597 8AO 0-10V/±10V DC
Manual
Version 1.0.0
Pos: 5 /Dokumentation al lgemein/Verzeic hnisse/Inhalts verzeichnis - Überschrift oG un d Verzeichni s @ 3\mod_12191512 30875_21.docx @ 21063 @ @ 1
Table of Contents
1Notes about this Documentation................................................................. 6
1.1 Validity of this Documentation................................................................. 6
1.2 Copyright................................................................................................... 6
1.3 Symbols..................................................................................................... 7
1.4 Number Notation....................................................................................... 9
1.5 Font Conventions ...................................................................................... 9
2Important Notes ......................................................................................... 10
2.1 Legal Bases ............................................................................................. 10
2.1.1 Subject to Changes ............................................................................. 10
2.1.2 Personnel Qualifications..................................................................... 10
2.1.3 Use of the WAGO-I/O-SYSTEM 750 in Compliance with
Underlying Provisions ........................................................................ 10
2.1.4 Technical Condition of Specified Devices ......................................... 11
2.2 Safety Advice (Precautions).................................................................... 12
3Device Description ..................................................................................... 14
3.1 View ........................................................................................................ 17
3.2 Connectors............................................................................................... 18
3.2.1 Data Contacts/Internal Bus................................................................. 18
3.2.2 Power Jumper Contacts/Field Supply ................................................ 19
3.2.3 Push-in CAGE CLAMP®Connectors................................................ 20
3.3 Display Elements .................................................................................... 22
3.4 Operating Elements................................................................................. 23
3.5 Schematic Diagram ................................................................................. 23
3.6 Technical Data ........................................................................................ 24
3.6.1 Device Data ........................................................................................ 24
3.6.2 Power Supply...................................................................................... 24
3.6.3 Communication .................................................................................. 24
3.6.4 Outputs ............................................................................................... 25
3.6.5 Connection Type ................................................................................ 25
3.6.6 Climatic Environmental Conditions ................................................... 26
3.7 Approvals ................................................................................................ 26
3.8 Standards and Guidelines........................................................................ 26
4Process Image............................................................................................. 27
4.1 Overview ................................................................................................. 28
4.2 Status Bytes............................................................................................. 29
4.3 Process Data ............................................................................................ 30
4.3.1 Overview of Signal Types .................................................................. 30
4.3.2 Signal Type „0-10 V”, ID0................................................................. 30
4.3.2.1 Amount/Sign Format ..................................................................... 30
4.3.2.2 Two's Complement Representation ............................................... 30
4.3.3 Signal Type “+/- 10 V”, ID1 .............................................................. 31
4.3.3.1 Amount/Sign Format ..................................................................... 31
4.3.3.2 Two's Complement Representation ............................................... 32

4 Table of Contents WAGO-I/O-SYSTEM 750
750-597 8AO 0-10V/±10V DC
Manual
Version 1.0.0
5Mounting..................................................................................................... 33
5.1 Mounting Sequence................................................................................. 33
5.2 Inserting and Removing Devices ............................................................ 34
5.2.1 Inserting the I/O Module .................................................................... 34
5.2.2 Removing the I/O Module.................................................................. 35
6Connect Devices ......................................................................................... 36
6.1 Connecting a Conductor to the Push-in CAGE CLAMP®...................... 36
6.2 Connection Example ............................................................................... 37
7Commissioning ........................................................................................... 38
7.1 Parameterization with WAGO-I/O-CHECK........................................... 38
7.1.1 Parameterization Dialog ..................................................................... 41
7.1.1.1 Title Bar ......................................................................................... 42
7.1.1.2 Main Menu..................................................................................... 42
7.1.1.3 Horizontal Tab Menu..................................................................... 43
7.1.1.3.1 “File” Tab.................................................................................. 43
7.1.1.3.1.1 “Open” Menu Item ............................................................... 44
7.1.1.3.1.2 “Save” Menu Item................................................................ 45
7.1.1.3.2 “Start” Tab ................................................................................ 45
7.1.1.3.3 “Connection” Tab ..................................................................... 46
7.1.1.4 Vertical Tab Menu......................................................................... 46
7.1.1.4.1 “Module settings” Menu Item................................................... 48
7.1.1.4.2 “Channel settings” Menu Item.................................................. 49
7.1.1.4.3 “Scaling” Menu Item ................................................................ 50
7.1.1.4.4 “Calibration” Menu Item .......................................................... 52
7.1.1.4.5 “Process Value” Menu Item...................................................... 54
7.1.1.4.6 “Information” Menu Item ......................................................... 55
7.1.1.5 Display Area .................................................................................. 55
7.1.1.6 Status Messages ............................................................................. 56
7.1.1.7 Status Bar....................................................................................... 56
7.2 Calibrating Process Values ..................................................................... 57
7.2.1 Example of Determining Gain and Offset.......................................... 58
7.3 Scaling Process Values ........................................................................... 59
8Diagnostics.................................................................................................. 60

WAGO-I/O-SYSTEM 750 Table of Contents 5
750-597 8AO 0-10V/±10V DC
Manual
Version 1.0.0
9Appendix..................................................................................................... 61
9.1 Configuration and Parameterization using a GSD File with PROFIBUS
DP and PROFINET IO............................................................................ 61
9.1.1 Configuration 8 AO 0-10 V, ±10 V DC S.E. ..................................... 61
9.1.1.1 PROFIBUS DP Fieldbus Coupler/Controller 750-333(/0xx-000),
750-833(/0xx-000)......................................................................... 61
9.1.1.2 PROFINET IO Fieldbus Coupler 750-370, 750-375(/025-000),
750-377(/025-000)......................................................................... 61
9.1.2 Parameterization 8 AI 0-10 V, ±10 V DC S.E. .................................. 62
9.1.2.1 All PROFIBUS DP and PROFINET IO Fieldbus Couplers.......... 64
9.1.2.2 PROFIBUS DP Fieldbus Coupler 750-333(/0xx-000), 750-
833(/0xx-000) ................................................................................ 65
9.1.2.3 PROFINET IO Fieldbus Coupler 750-370 .................................... 66
9.1.2.4 PROFINET IO Fieldbus Coupler 750-375(/025-000), 750-
377(/025-000) ................................................................................ 67
List of Figures ...................................................................................................... 68
List of Tables........................................................................................................ 69
=== Ende der Liste für Textmarke Verzeichni s_vorne ===
Pos: 7 /Alle Serien (Allge meine Module)/Übersc hriften/Neue Übersc hriften/Ebene 1Hin weise zu dieser Dokumenta tion - Überschrift 1 @ 4\mod_123 7987661750_21.doc x @ 29029 @ 1 @ 1

6 Table of Contents WAGO-I/O-SYSTEM 750
750-597 8AO 0-10V/±10V DC
Manual
Version 1.0.0
1 Notes about this Documentation
Pos: 8 /Alle Serien (Al lgemeine Module)/Si cherheits- und sonstige Hin weise/HinweisHin weis: Dokumentation aufb ewahren @ 4\mod_123798733 9812_21.docx @ 29026 @ @ 1
Always retain this documentation!
This documentation is part of the product. Therefore, retain the documentation
during the entire service life of the product. Pass on the documentation to any
subsequent user. In addition, ensure that any supplement to this documentation is
included, if necessary.
Pos: 9 /Alle Serien (Al lgemeine Module)/Über schriften/Neue Über schriften/Ebene 2Gü ltigkeitsbereic h - Überschrift 2 @ 12\mod_13389 12448776_21.docx @ 96469 @ 2 @ 1
1.1 Validity of this Documentation
Pos: 10 /Serie 750 (W AGO-I/O-SYSTEM)/Hinweise zur Dokumentation/ Gültigkeitsber eichGültigkeitsb ereich Dokumentatio n Busklemme 750-xxxx, nur Standar dversion @ 14\mod_135894 4037400_21.doc x@ 109342 @ @ 1
This documentation is only applicable to the I/O module 750-597
(8AO 0-10V/±10V DC).
Pos: 11 /Serie 750 (W AGO-I/O-SYSTEM)/Hinweise zur Dokumentation/ Hinweise/Achtung: Hinweiszur Doku mentation Buskle mmen7 50-xxxx @ 4\mod_123798 6979656_21.docx @ 29023 @ @ 1
The I/O module 750-597 shall only be installed and operated according to the
instructions in this manual and in the manual for the used fieldbus
coupler/controller.
Consider power layout of the WAGO-I/O-SYSTEM 750!
In addition to these operating instructions, you will also need the manual for the
used fieldbus coupler/controller, which can be downloaded at www.wago.com.
There, you can obtain important information including information on electrical
isolation, system power and supply specifications.
Pos: 12.1 /Alle Serien ( Allgemeine Module)/ Überschriften/Ebene 2/ Urheberschutz - Übersc hrift 2 @ 23\mod_1435647 042188_21.docx @ 184808 @ 2 @ 1
1.2 Copyright
Pos: 12.2 /Alle Serien ( Allgemeine Module)/ Rechtliches, Allge meines/Urheberschut z ausführlich @ 4\mod_1235565 145234_21.doc x@ 27691 @ @ 1
This Manual, including all figures and illustrations, is copyright-protected. Any
further use of this Manual by third parties that violate pertinent copyright
provisions is prohibited. Reproduction, translation, electronic and phototechnical
filing/archiving (e.g., photocopying) as well as any amendments require the
written consent of WAGO Kontakttechnik GmbH & Co. KG, Minden, Germany.
Non-observance will involve the right to assert damage claims.
Pos: 12.3 /Dokumenta tion allgemein/Glied erungselemente/---Sei tenwechsel--- @ 3\mod_122110804 5078_0.docx @ 21810 @ @1

7 Notes about this Documentation WAGO-I/O-SYSTEM 750
750-597 8AO 0-10V/±10V DC
Manual
Version 1.0.0
Pos: 12.4 /Alle Serien ( Allgemeine Module)/ Überschriften/Neue Überschriften/Ebene 2Symbole - Übersc hrift 2 @ 13\mod_1351068042 408_21.docx @ 105270 @ 2 @ 1
1.3 Symbols
Pos: 12.5.1 /Alle Serien ( Allgemeine Module) /Sicherheits- und sonsti ge Hinweise/Gefahr /Gefahr: _Warnung vor Per sonenschäden allgem ein_ - Erläuterung @ 13\mod_1343 309450020_21.doc x@ 101 029@ @ 1
Personal Injury!
Indicates a high-risk, imminently hazardous situation which, if not avoided, will
result in death or serious injury.
Pos: 12.5.2 /Alle Serien ( Allgemeine Module) /Sicherheits- und sonsti ge Hinweise/Gefahr /Gefahr: _Warnung vor Per sonenschäden durc h elektrischen Strom_ - Erläut erung @ 13\mod_134330969491 4_21.docx @ 101030 @ @1
Personal Injury Caused by Electric Current!
Indicates a high-risk, imminently hazardous situation which, if not avoided, will
result in death or serious injury.
Pos: 12.5.3 /Alle Serien ( Allgemeine Module) /Sicherheits- und sonsti ge Hinweise/W arnung/Warnung: _Warnung vor Personenschäden allgemein_ - Erläuterung @ 13\mo d_1343309877041_21.doc x @ 101035 @ @1
Personal Injury!
Indicates a moderate-risk, potentially hazardous situation which, if not avoided,
could result in death or serious injury.
Pos: 12.5.4 /Alle Serien ( Allgemeine Module) /Sicherheits- und sonsti ge Hinweise/Vorsi cht/Vorsicht: _W arnung vor Personenschäden a llgemein_ - Erläuterung @ 13\mod_1343 310028762_21.doc x @ 101038@ @ 1
Personal Injury!
Indicates a low-risk, potentially hazardous situation which, if not avoided, may
result in minor or moderate injury.
Pos: 12.5.5 /Alle Serien ( Allgemeine Module) /Sicherheits- und sonsti ge Hinweise/Achtung/ Achtung: _Warnung vor Sachschädenal lgemein_ - Erläuterung @ 13\mod_ 1343310134623_21.doc x@ 101 041 @ @1
Damage to Property!
Indicates a potentially hazardous situation which, if not avoided, may result in
damage to property.
Pos: 12.5.6 /Alle Serien ( Allgemeine Module) /Sicherheits- und sonsti ge Hinweise/Achtung/ Achtung: _Warnung vor Sachschädendur ch elektrostatisc he Aufladung_ - Erläuterung @ 13\mod_134 3310227702_21.doc x@ 101044 @ @ 1
Damage to Property Caused by Electrostatic Discharge (ESD)!
Indicates a potentially hazardous situation which, if not avoided, may result in
damage to property.
Pos: 12.5.7 /Alle Serien ( Allgemeine Module) /Sicherheits- und sonsti ge Hinweise/Hinwei s/Hinweis: _Wic htiger Hinweis allgemein_ - Er läuterung @ 13\mod_1343310326 906_21.docx @ 101047 @ @ 1
Important Note!
Indicates a potential malfunction which, if not avoided, however, will not result in
damage to property.
Pos: 12.5.8 /Alle Serien ( Allgemeine Module) /Sicherheits- und sonsti ge Hinweise/Inf ormation/Informatio n: _Weitere Inf ormation allgemein_ - Erläuter ung @ 13\mod_1343310439814_21. docx @ 101051 @ @1

8 Table of Contents WAGO-I/O-SYSTEM 750
750-597 8AO 0-10V/±10V DC
Manual
Version 1.0.0
Additional Information:
Refers to additional information which is not an integral part of this
documentation (e.g., the Internet).
Pos: 12.6 /Dokumentati on allgemein/Glieder ungselemente/---Seitenwec hsel--- @ 3\mod_1221108045078 _0.docx @ 21810 @ @1

9 Notes about this Documentation WAGO-I/O-SYSTEM 750
750-597 8AO 0-10V/±10V DC
Manual
Version 1.0.0
Pos: 12.7 /Alle Serien ( Allgemeine Module)/ Überschriften/Ebene 2/ Darstellung der Zahlensysteme - Überschr ift 2 @ 23\mod_1435647128 078_21.docx @ 184811 @ 2 @ 1
1.4 Number Notation
Pos: 12.8 /Alle Serien ( Allgemeine Module)/ Rechtliches, Allge meines/Zahlensyste me@ 3\mo d_1221059454015 _21.docx @ 2171 1 @ @1
Table 1: Number Notation
Number Code
Example
Note
Decimal
100
Normal notation
Hexadecimal
0x64
C notation
Binary
'100'
'0110.0100'
In quotation marks, nibble separated with
dots (.)
Pos: 12.9 /Alle Serien ( Allgemeine Module)/ Überschriften/Ebene 2/ Schriftkonventio nen - Überschrift 2 @23\mod_1435647186005_ 21.docx @ 184814 @ 2 @ 1
1.5 Font Conventions
Pos: 12.10 /Alle Seri en (Allgemeine Module)/ Rechtliches, Allge meines/Schrif tkonventionen @ 3\mod_1221059521 437_21.docx @ 21714 @ @ 1
Table 2: Font Conventions
Font Type
Indicates
italic
Names of paths and data files are marked in italic-type.
e.g.: C:\Program Files\WAGO Software
Menu
Menu items are marked in bold letters.
e.g.: Save
>
A greater-than sign between two names means the selection of a
menu item from a menu.
e.g.: File > New
Input
Designation of input or optional fields are marked in bold letters,
e.g.: Start of measurement range
“Value”
Input or selective values are marked in inverted commas.
e.g.: Enter the value “4 mA” under Start of measurement range.
[Button]
Pushbuttons in dialog boxes are marked with bold letters in square
brackets.
e.g.: [Input]
[Key]
Keys are marked with bold letters in square brackets.
e.g.: [F5]
Pos: 13 /Dokumentation al lgemein/Glieder ungselemente/---Seitenwec hsel--- @ 3\mod_122110804507 8_0.docx @ 21810 @ @1

10 Table of Contents WAGO-I/O-SYSTEM 750
750-597 8AO 0-10V/±10V DC
Manual
Version 1.0.0
Pos: 14 /Alle Serien ( Allgemeine Module)/ Überschriften/Neue Überschriften/Eben e 1Wichtige Erläuter ungen - Überschrift 1 @ 4\mod_1241428899156_21.d ocx @ 32170 @ 1 @ 1
2 Important Notes
Pos: 15.1 /Alle Serien ( Allgemeine Module)/ Rechtliches, Allge meinesWichtige Erläu terungen - Einleitung @ 3\mod_122 1059818031_21.doc x@ 21717 @ @ 1
This section includes an overall summary of the most important safety
requirements and notes that are mentioned in each individual section. To protect
your health and prevent damage to devices as well, it is imperative to read and
carefully follow the safety guidelines.
Pos: 15.2 /Alle Serien ( Allgemeine Module)/ Überschriften/Neue Überschriften/ Ebene 2Rechtliche Grund lagen - Überschrift 2 @ 3\mod_12210606263 43_21.docx @ 21726 @ 2 @ 1
2.1 Legal Bases
Pos: 15.3 /Alle Serien ( Allgemeine Module)/ Rechtliches, Allge meinesÄnderungsvorbeha lt - Überschrift 3 und Inhalt @ 3\mod_1221060036 484_21.docx @ 21720 @ 3 @ 1
2.1.1 Subject to Changes
WAGO Kontakttechnik GmbH & Co. KG reserves the right to provide for any
alterations or modifications that serve to increase the efficiency of technical
progress. WAGO Kontakttechnik GmbH & Co. KG owns all rights arising from
the granting of patents or from the legal protection of utility patents. Third-party
products are always mentioned without any reference to patent rights. Thus, the
existence of such rights cannot be excluded.
Pos: 15.4 /Serie 750 (W AGO-I/O-SYSTEM)/Wichtige Erläuterun gen/Personalqualif ikationPersonal qualifikation 750-xxxx - Übersc hrift 3 und Inhalt @ 3\mod_1224061208046_2 1.docx @ 24063 @ 3 @ 1
2.1.2 Personnel Qualifications
All sequences implemented on WAGO-I/O-SYSTEM 750 devices may only be
carried out by electrical specialists with sufficient knowledge in automation. The
specialists must be familiar with the current norms and guidelines for the devices
and automated environments.
All changes to the coupler or controller should always be carried out by qualified
personnel with sufficient skills in PLC programming.
Pos: 15.5 /Serie 750 (W AGO-I/O-SYSTEM)/Wichtige Erläuterun gen/Bestimmungsgem äße VerwendungBestim mungsgemäße Verwendung 750-xxxx - Ü berschrift 3 und I nhalt @ 3\mod_12240641512 34_21.docx @ 24070 @ 3 @ 1
2.1.3 Use of the WAGO-I/O-SYSTEM 750 in Compliance with
Underlying Provisions
Fieldbus couplers, fieldbus controllers and I/O modules found in the modular
WAGO-I/O-SYSTEM 750 receive digital and analog signals from sensors and
transmit them to actuators or higher-level control systems. Using programmable
controllers, the signals can also be (pre-) processed.
The devices have been developed for use in an environment that meets the IP20
protection class criteria. Protection against finger injury and solid impurities up to
12.5 mm diameter is assured; protection against water damage is not ensured.
Unless otherwise specified, operation of the devices in wet and dusty
environments is prohibited.
Operating the WAGO-I/O-SYSTEM 750 devices in home applications without
further measures is only permitted if they meet the emission limits (emissions of
interference) according to EN 61000-6-3. You will find the relevant information
in the section “Device Description” > “Standards and Guidelines” in the manual
for the used fieldbus coupler/controller.

11 Important Notes WAGO-I/O-SYSTEM 750
750-597 8AO 0-10V/±10V DC
Manual
Version 1.0.0
Appropriate housing (per 94/9/EG) is required when operating the WAGO-I/O-
SYSTEM 750 in hazardous environments. Please note that a prototype test
certificate must be obtained that confirms the correct installation of the system in
a housing or switch cabinet.
Pos: 15.6 /Alle Serien ( Allgemeine Module)/ Rechtliches, Allge meinesTechnischer Zust and der Geräte - Überschri ft 3 und Inhalt @ 3\mod_12210 60446109_21.docx @ 21723 @ 3 @ 1
2.1.4 Technical Condition of Specified Devices
The devices to be supplied ex works are equipped with hardware and software
configurations, which meet the individual application requirements. WAGO
Kontakttechnik GmbH & Co. KG will be exempted from any liability in case of
changes in hardware or software as well as to non-compliant usage of devices.
Please send your request for modified and new hardware or software
configurations directly to WAGO Kontakttechnik GmbH & Co. KG.
Pos: 15.7 /Dokumenta tion allgemein/Glied erungselemente/---Sei tenwechsel--- @ 3\mod_122110804 5078_0.docx @ 21810 @ @ 1

12 Table of Contents WAGO-I/O-SYSTEM 750
750-597 8AO 0-10V/±10V DC
Manual
Version 1.0.0
Pos: 15.8 /Alle Serien ( Allgemeine Module)/ Überschriften/Neue Überschriften/ Ebene 2Sicherheitshi nweise - Überschrift 2 @ 6\mod_1260180299987_21. docx @ 46724 @ 2 @ 1
2.2 Safety Advice (Precautions)
Pos: 15.9 /Alle Serien ( Allgemeine Dokumente) (Allgemeine Module) /Wichtige Erläuter ungen/Sicher heitshinweise/Einlei tung Sicherheitshi nweise Hardware @ 6\mod_1260 180170493_21.doc x@ 46720 @ @ 1
For installing and operating purposes of the relevant device to your system the
following safety precautions shall be observed:
Pos: 15.10.1 /Alle Ser ien (Allgemeine Dokumen te) (Allgemeine Module) /Wichtige Erläu terungen/Sicherhei tshinweise/Gefahr /Gefahr: Nicht an Gerä ten unter Spannung arbei ten! @ 6\mod_1260180365327 _21.docx @ 46727 @ @ 1
Do not work on devices while energized!
All power sources to the device shall be switched off prior to performing any
installation, repair or maintenance work.
Pos: 15.10.2 /Seri e 750 (WAGO-I/O-SYSTEM)/Wichtige Erläut erungen/Sicherheits- und s onstige Hinweise/ Gefahr/Gefahr: Ei nbau 0750-xxxx nur in Gehäusen, Sc hränken oder elektrischen Be triebsräumen! @ 6\mod_126 0180556692_21.doc x@ 46731 @ @ 1
Install the device only in appropriate housings, cabinets or in electrical
operation rooms!
The WAGO-I/O-SYSTEM 750 and its components are an open system. As such,
install the system and its components exclusively in appropriate housings,
cabinets or in electrical operation rooms. Allow access to such equipment and
fixtures to authorized, qualified staff only by means of specific keys or tools.
Pos: 15.10.3 /Alle Ser ien (Allgemeine Dokumen te) (Allgemeine Module) /Wichtige Erläu terungen/Sicherhei tshinweise/Gefahr /Gefahr: Unfallver hütungsvorschri ften beachten! @ 6\mod_12601806 57000_21.docx @ 46735 @ @ 1
Pos: 15.10.4 /Alle Ser ien (Allgemeine Dokumen te) (Allgemeine Module) /Wichtige Erläu terungen/Sicherhei tshinweise/Gefahr /Gefahr: Auf normgerec hten Anschluss achten! @ 6\mod_1260180753479_ 21.docx @ 46739 @ @ 1
Pos: 15.11.1 /Alle Ser ien (Allgemeine Dokumen te) (Allgemeine Module) /Wichtige Erläu terungen/Sicherhei tshinweise/Achtun g/Achtung: Defekte od er beschädigte Geräte au stauschen! @ 6\mod_126018 0857358_21.docx @ 46743 @ @ 1
Replace defective or damaged devices!
Replace defective or damaged device/module (e.g., in the event of deformed
contacts), since the long-term functionality of device/module involved can no
longer be ensured.
Pos: 15.11.2 /Alle Ser ien (Allgemeine Dokumen te) (Allgemeine Module) /Wichtige Erläu terungen/Sicherhei tshinweise/Achtun g/Achtung: Geräte vor kriechenden und iso lierenden Stoffen sc hützen! @ 6\mod_126018103621 6_21.docx @ 46747 @ @ 1
Protect the components against materials having seeping and insulating
properties!
The components are not resistant to materials having seeping and insulating
properties such as: aerosols, silicones and triglycerides (found in some hand
creams). If you cannot exclude that such materials will appear in the component
environment, then install the components in an enclosure being resistant to the
above-mentioned materials. Clean tools and materials are imperative for handling
devices/modules.
Pos: 15.11.3 /Alle Ser ien (Allgemeine Dokumen te) (Allgemeine Module) /Wichtige Erläu terungen/Sicherhei tshinweise/Achtun g/Achtung: Reini gung nur mit zulässigen Materi alien! @ 6\mod_12601812 03293_21.docx @ 46751 @ @ 1
Clean only with permitted materials!
Clean soiled contacts using oil-free compressed air or with ethyl alcohol and
leather cloths.
Pos: 15.11.4 /Alle Ser ien (Allgemeine Dokumen te) (Allgemeine Module) /Wichtige Erläu terungen/Sicherhei tshinweise/Achtun g/Achtung: Kein Kontak tspray verwenden! @ 6\mod_126 0181290808_21.doc x @ 46755@ @ 1

13 Important Notes WAGO-I/O-SYSTEM 750
750-597 8AO 0-10V/±10V DC
Manual
Version 1.0.0
Do not use any contact spray!
Do not use any contact spray. The spray may impair contact area functionality in
connection with contamination.
Pos: 15.11.5 /Alle Ser ien (Allgemeine Dokumen te) (Allgemeine Module) /Wichtige Erläu terungen/Sicherhei tshinweise/Achtun g/Achtung: Verpolun g vermeiden! @ 6\mod_1260184 045744_21.doc x@ 46767 @ @ 1
Do not reverse the polarity of connection lines!
Avoid reverse polarity of data and power supply lines, as this may damage the
devices involved.
Pos: 15.11.6 /Alle Ser ien (Allgemeine Dokumen te) (Allgemeine Module) /Wichtige Erläu terungen/Sicherhei tshinweise/Achtun g/Achtung: Elektrosta tische Entladung ver meiden! @ 6\mod_12601813647 29_21.docx @ 46759 @ @ 1
Avoid electrostatic discharge!
The devices are equipped with electronic components that may be destroyed by
electrostatic discharge when touched. Please observe the safety precautions
against electrostatic discharge per DIN EN 61340-5-1/-3. When handling the
devices, please ensure that environmental factors (personnel, work space and
packaging) are properly grounded.
Pos: 16 /Dokumentation al lgemein/Glieder ungselemente/---Seitenwec hsel--- @ 3\mod_122110804507 8_0.docx @ 21810 @ @ 1

14 Table of Contents WAGO-I/O-SYSTEM 750
750-597 8AO 0-10V/±10V DC
Manual
Version 1.0.0
Pos: 17 /Alle Serien ( Allgemeine Module)/ Überschriften/Neue Überschriften/Eben e 1Gerätebeschreibun g - Überschrift 1 @ 3\mod_123 3756084656_21.doc x@ 27096 @ 1 @ 1
3 Device Description
Pos: 18.1.1 /Seri e 750 (WAGO-I/O-SYSTEM)/Gerätebeschrei bung/Einleitung/An wendung/AO/Anwendu ng 750-04xx AO SE ( 0...10V oder ±10V) @ 25\mod_1453 466643598_21.doc x@ 199050 @ @ 1
The 750-597 I/O module (8AO 0-10V/±10V DC) generates standardized values of
0 V ... +10 V or −10 V … +10 V for the field range.
Pos: 18.1.2 /Seri e 750 (WAGO-I/O-SYSTEM)/Gerätebeschrei bung/Einleitung/ I/O-Beschreibung/A O/I/O-Beschreibung 750-05 xx8 A O SE Felddsignale über AO1 und M asse bzw. AO2....AO8 und Mass e @ 25\mod_1453462065782_ 21.docx @ 199038 @ @ 1
The I/O module has 8 output channels for field signals.
The actuators are connected to push-in CAGE CLAMP®terminals AO1 and
ground or AO2 … AO8 and respective ground.
The ground connections are available for all 8 channels on a common 0V ground
potential.
Pos: 18.1.3 /Seri e 750 (WAGO-I/O-SYSTEM)/Gerätebeschreibung/ Einleitung/I/ O-Beschreibung/Allg emein/Verweis auf Kapitel "Anschlüs se" @ 8\mod_127677537 8035_21.docx @ 57956 @ @ 1
The assignment of the connections is described in the “Connectors” section.
Pos: 18.1.4 /Seri e 750 (WAGO-I/O-SYSTEM)/Gerätebeschreibung/E inleitung/I/ O-Beschreibung/Allge mein/Verweis auf Kapitel "Gerät e anschließen" > "Anschlussbeis piel(e)" @ 5\mod_12460152032 81_21.docx @ 36298 @ @ 1
Connection examples are shown in section “Connecting Devices” > … >
“Connection Example(s)”.
Pos: 18.1.5 /Seri e 750 (WAGO-I/O-SYSTEM)/Gerätebeschrei bung/Einleitung/ I/O-Beschreibung/A O/I/O-Beschreibung 750-05 xxA O kurzschlussfes t, aber Störung der Signale a nderer Kanäle @ 25\mod_14558 96634269_21.docx @ 202047 @ @ 1
The I/O module outputs are short-circuit-proof. However, a short circuit in an
output causes interruption in the other outputs of the I/O module.
Pos: 18.1.6 /Seri e 750 (WAGO-I/O-SYSTEM)/Gerätebeschrei bung/Einleitung/Funk tion/Galvanisc he Trennung Ausgangssi gnal/Systemebene ( 12 Bit) @ 5\mod_1247050641729_ 21.docx @ 36877 @ @ 1
The Output signal is electrically isolated and will be transmitted with a resolution
of 12 bits.
Pos: 18.1.7 /Seri e 750 (WAGO-I/O-SYSTEM)/Gerätebeschrei bung/Einleitung/ LED-Anzeige/LED Zustand Be trieb und Klemmenbus-Ko mmunikation @ 5\mod_1247054 901573_21.docx @ 36892 @ @ 1
The operational readiness and the trouble-free internal data bus communication of
the channels are indicated via a green function LED.
Pos: 18.1.8 /Seri e 750 (WAGO-I/O-SYSTEM)/Gerätebeschrei bung/Einleitung/ LED-Anzeige/LED Fehler Feldversorgung @ 25\mod_1 453801812764_21.doc x @ 199238 @ @ 1
A red error LED displays the status of the field-side power supply voltage.
Pos: 18.1.9 /Seri e 750 (WAGO-I/O-SYSTEM)/Gerätebeschreibung/Ei nleitung/LED-Anzeig e/Verweis auf K apitel "Anzeigee lemente" @ 5\mod_1246010525 000_21.docx @ 36194 @ @ 1
The meaning of the LEDs is described in the “Display Elements” section.
Pos: 18.1.10 /Seri e 750 (WAGO-I/O-SYSTEM)/Gerätebeschrei bung/Einleitung/ Versorgung/Spannung sversorgung aus Sy stemspannung @ 5\mod_12471164 33759_21.docx @ 36920 @ @ 1
Power to the internal electronics is supplied via internal data bus.
Pos: 18.1.11 /Seri e 750 (WAGO-I/O-SYSTEM)/Gerätebeschrei bung/Einleitung/ Versorgung/Versor gung 24 V, 0 V über Leistungsko ntakte Standard @ 3\mod_1226 498974531_21.doc x@ 25020 @ @ 1
The I/O module 750-597 (8AO 0-10V/±10V DC) receives the 24 V voltage
supply for the field level from an upstream I/O module or from the fieldbus
coupler/controller via blade-formed power jumper contacts. It then provides these
potentials to subsequent I/O modules via spring-formed power jumper contacts.
Pos: 18.1.12 /Seri e 750 (WAGO-I/O-SYSTEM)/Wichtige Erläut erungen/Sicherheits- und s onstige Hinweise/Ac htung/Achtung: Maxi maler Strom Leistungs kontakte 10 A @ 3\mod_122649914 3500_21.docx @ 25029 @ @ 1
Do not exceed maximum current via power jumper contacts!
The maximum current to flow through the power jumper contacts is 10 A.
Greater currents can damage the contacts.
When configuring your system, ensure that this current is not exceeded. If
exceeded, insert an additional supply module.
Pos: 18.1.13 /Seri e 750 (WAGO-I/O-SYSTEM)/Gerätebeschrei bung/Einleitung/Ver sorgung/Anordnu ng unter Berücksic htigung der Leistungskonta kte beliebig @ 3\mod_1233756 233468_21.doc x@ 27099 @ @ 1
With consideration of the power jumper contacts, the individual modules can be
arranged in any combination when configuring the fieldbus node. An arrangement
in groups within the group of potentials is not necessary.
Pos: 18.1.14 /Seri e 750 (WAGO-I/O-SYSTEM)/Gerätebeschrei bung/Einleitung/ Einsatzbereic h/Einsatzbereic h 750-xxxxnur K oppler/Controller aus Kompa tibilitätsliste @ 4\mod_12423894 40265_21.docx @ 33262 @ @ 1
The 750-597 module can be used with the fieldbus couplers and controllers of the
WAGO-I/O-SYSTEM 750 of the specified version or higher listed in the
“Compatibility list” table.
Pos: 18.1.15 /Seri e 750 (WAGO-I/O-SYSTEM)/Gerätebeschrei bung/Einleitung/ Einsatzbereic h/Kompatibilitäts listen/Kompatibili tätsliste 750-0597 @ 25\mod_1457429566887_ 21.docx @ 203608 @ @ 1

15 Device Description WAGO-I/O-SYSTEM 750
750-597 8AO 0-10V/±10V DC
Manual
Version 1.0.0
Table 3: Compatibility List 750-597
Bus System Fieldbus Couplers/Controllers Item No.
Firmware
Revision Status
PROFINET Fieldbus coupler
750-375
03
750-377
03
PROFIBUS Fieldbus coupler 750-333 17
Controller 750-833 16
ETHERNET
Fieldbus coupler
750-342
18
750-352
04
Controller
750-841
20
750-842
19
750-843
03
750-852
01
750-871
08
750-872
04
750-873
04
750-880
04
750-881
04
750-882
04
750-885
04
PFC200 fieldbus controller
750-82xx
01
BA application controller
750-884
05
DeviceNet
Fieldbus coupler
750-306
4L
ECO Fieldbus Coupler
750-346
11
Controller
750-806
11
CANopen
Fieldbus coupler
750-337
20
750-338
20
ECO fieldbus coupler
750-347
10
750-348
10
Controller
750-837
15
750-838
15
Modbus
Fieldbus coupler
750-315/300-000
01
750-316/300-000
01
Controller
750-815/300-000
01
750-816/300-000
01
EtherCat
Fieldbus coupler
750-354
03
CC-Link
Fieldbus coupler
750-310
03
BACnet
Controller
750-831
03
KNX
Controller
750-889
07
LonWorks®
Controller
750-819
09

16 Table of Contents WAGO-I/O-SYSTEM 750
750-597 8AO 0-10V/±10V DC
Manual
Version 1.0.0
The 750-597 I/O module cannot be operated on the following fieldbus couplers:
• 750-320
• 750-323
• 750-324
• 750-327
• 750-343
• 750-351
Pos: 18.2 /Dokumenta tion allgemein/Glied erungselemente/---Sei tenwechsel--- @ 3\mod_122110804 5078_0.docx @ 21810 @ @ 1

17 Device Description WAGO-I/O-SYSTEM 750
750-597 8AO 0-10V/±10V DC
Manual
Version 1.0.0
Pos: 18.3 /Alle Serien ( Allgemeine Module)/ Überschriften/Neue Überschriften/ Ebene 2Ansicht - Überschri ft 2 @ 4\mod_124098421734 3_21.docx @ 31958 @ 2 @ 1
3.1 View
Pos: 18.4 /Serie 750 (W AGO-I/O-SYSTEM)/Gerätebeschreibung/ Ansicht/Analogau sgangsklemmen/Ansi cht 750-0597 @ 25\mod_14534 73238404_21.docx @ 199128 @ @ 1
Figure 1: View of Device
Pos: 18.5 /Serie 750 (W AGO-I/O-SYSTEM)/Gerätebeschreibung/ Ansicht/Ansic ht Push-in CageClamp®_Legen de mit LEDs @ 15\mod_1370852 562803_21.docx @ 122213 @ @ 1
Table 4: Legend for Figure “View”
Pos.
Description
Details See Section
1
Marking possibility with
Mini-WSB
---
2
Status LEDs
“Device Description” > “Display Elements”
3
Data contacts
“Device Description” > “Connectors”
4
Push-in CAGE CLAMP®
connectors
“Device Description” > “Connectors”
5
Power jumper contacts
“Device Description” > “Connectors”
6
Release tab
“Mounting” > “Inserting and Removing
Devices”
Pos: 18.6 /Dokumenta tion allgemein/Glied erungselemente/---Sei tenwechsel--- @ 3\mod_1221108045078 _0.docx @ 21810 @ @ 1

18 Table of Contents WAGO-I/O-SYSTEM 750
750-597 8AO 0-10V/±10V DC
Manual
Version 1.0.0
Pos: 18.7 /Alle Serien ( Allgemeine Module)/ Überschriften/Neue Überschriften/ Ebene 2Anschlüsse - Überschr ift 2 @ 4\mod_1240984262 656_21.docx @ 31961 @ 2 @ 1
3.2 Connectors
Pos: 18.8 /Serie 750 (W AGO-I/O-SYSTEM)/Gerätebeschreibung/Ansch lüsse/Datenkontak te/Klemmenbus - Überschr ift 3 @ 6\mod_1256294684083_ 21.docx @ 43660 @ 3 @ 1
3.2.1 Data Contacts/Internal Bus
Pos: 18.9.1 /Seri e 750 (WAGO-I/O-SYSTEM)/Gerätebeschrei bung/Anschlüsse/Dat enkontakte - Feldbuskopp ler/-controller, Abbi ldung und Beschreibung @ 3\mod_123 1771259187_21.doc x @ 26002 @ @ 1
Communication between the fieldbus coupler/controller and the I/O modules as
well as the system supply of the I/O modules is carried out via the internal bus. It
is comprised of 6 data contacts, which are available as self-cleaning gold spring
contacts.
Figure 2: Data Contacts
Pos: 18.9.2 /Seri e 750 (WAGO-I/O-SYSTEM)/Wichtige Erläuterun gen/Sicherheits- und so nstige Hinweise/Ac htung/Achtung: Busk lemmen nicht auf Goldfeder kontakte legen! @ 7\mod_126 6318463636_21.doc x @ 50695@ @ 1
Do not place the I/O modules on the gold spring contacts!
Do not place the I/O modules on the gold spring contacts in order to avoid soiling
or scratching!
Pos: 18.9.3 /Seri e 750 (WAGO-I/O-SYSTEM)/Wichtige Erläuterun gen/Sicherheits- und so nstige Hinweise/Ac htung/Achtung: ESD - A uf gute Erdung der Umgebung achten! @ 7\mod_1266318538667_ 21.docx @ 50708 @ @ 1
Ensure that the environment is well grounded!
The devices are equipped with electronic components that may be destroyed by
electrostatic discharge. When handling the devices, ensure that the environment
(persons, workplace and packing) is well grounded. Avoid touching conductive
components, e.g. data contacts.
Pos: 18.10 /Dokumenta tion allgemein/Glie derungselemente/---Sei tenwechsel--- @ 3\mod_1221108045078_0. docx @ 21810 @ @ 1

19 Device Description WAGO-I/O-SYSTEM 750
750-597 8AO 0-10V/±10V DC
Manual
Version 1.0.0
Pos: 18.11 /Serie 750 (W AGO-I/O-SYSTEM)/Gerätebeschreibung/ Anschlüsse/Leis tungskontakte/Fe ldversorgung - Überschr ift 3 @ 6\mod_1256294692864_2 1.docx @ 43664 @ 3 @ 1
3.2.2 Power Jumper Contacts/Field Supply
Pos: 18.12.1 /Seri e 750 (WAGO-I/O-SYSTEM)/Wichtige Erläut erungen/Sicherheits- und s onstige Hinweise/Vor sicht/Vorsicht: Verletzungsg efahr durch scharf kantige Messerkontakte! @ 6\mod_1256193279401_ 21.docx @ 43414 @ @ 1
Risk of injury due to sharp-edged blade contacts!
The blade contacts are sharp-edged. Handle the I/O module carefully to prevent
injury.
Pos: 18.12.2 /Seri e 750 (WAGO-I/O-SYSTEM)/Gerätebeschreibung/An schlüsse/Leistun gskontakte 2 LK (Messer/ Leistungskontakt e 2 LK (Messer/Feder) - Ei nleitung @ 15\mod_1371721641099_2 1.docx @ 123714 @ @ 1
The I/O module 750-597 has 2 self-cleaning power jumper contacts that supply
and transmit power for the field side. The contacts on the left side of the I/O
module are designed as blade contacts and those on the right side as spring
contacts.
Pos: 18.12.3 /Seri e 750 (WAGO-I/O-SYSTEM)/Gerätebeschrei bung/Anschlüsse/Lei stungskontakte 2 LK ( Messer/Feder) - Abbildung (16-K anal) @ 15\mod_137086661058 2_21.docx @ 122222 @ @ 1
Figure 3: Power Jumper Contacts
Pos: 18.12.4 /Seri e 750 (WAGO-I/O-SYSTEM)/Gerätebeschrei bung/Anschlüsse/Lei stungskontak te2 LK (Messer/Leis tungskontakte 2 LK (Messer /Feder) - Legende @ 15\mod_13717 21352500_21.docx @ 123710 @ @ 1
Table 5: Legend for Figure “Power Jumper Contacts”
Contact
Type
Function
1
Spring contact
Potential transmission (Uv) for field supply
2
Spring contact
Potential transmission (0 V) for field supply
3
Blade contact
Potential feed-in (0 V) for field supply
4
Blade contact
Potential feed-in (Uv) for field supply
Pos: 18.12.5 /Seri e 750 (WAGO-I/O-SYSTEM)/Wichtige Erläut erungen/Sicherhei ts- und sonstige Hinweise/A chtung/Achtung: Maximaler Strom Lei stungskontakte 10 A @ 3\mod_12264 99143500_21.doc x@ 2502 9 @ @ 1
Do not exceed maximum current via power jumper contacts!
The maximum current to flow through the power jumper contacts is 10 A.
Greater currents can damage the contacts.
When configuring your system, ensure that this current is not exceeded. If
exceeded, insert an additional supply module.
Pos: 18.12.6 /Seri e 750 (WAGO-I/O-SYSTEM)/Wichtige Erläut erungen/Sicherheits- und s onstige Hinweise/ Hinweis/Hinweis: Po tentialeinspeisek lemme für Erde einsetzen! (keine LK für Er de) @ 3\mod_1226499037468_21.doc x @ 25023 @ @ 1

20 Table of Contents WAGO-I/O-SYSTEM 750
750-597 8AO 0-10V/±10V DC
Manual
Version 1.0.0
Use supply modules for ground (earth)!
The I/O module has no power jumper contacts for receiving and transmitting the
earth potential. Use a supply module when an earth potential is needed for the
subsequent I/O modules.
Pos: 18.13 /Dokumenta tion allgemein/Glie derungselemente/------Leerzei le------@ 3\mod_1224662755 687_0.docx @ 24460 @ @ 1
Pos: 18.14 /Serie 750 (W AGO-I/O-SYSTEM)/Gerätebeschreibung/ Anschlüsse/Pus h-in CAGE CLAMP®-Anschlüsse - Übersc hrift 3 @ 15\mod_1370519905 692_21.docx @ 122018 @ 3 @ 1
3.2.3 Push-in CAGE CLAMP®Connectors
Pos: 18.15 /Serie 750 (W AGO-I/O-SYSTEM)/Gerätebeschreibung/ Anschlüsse/Analo gausgangsklemmen/ Anschlüsse 750-0597 @ 25\mod_14538070 51902_21.docx @ 199303 @ @ 1
Figure 4: Push-in CAGE CLAMP®Connections