WAGO 852 Series User manual

Manual
WAGO ETHERNET Accessories 852
852-103
Industrial Switch
8
Ports 100BASE-TX; 2 Slots 100BASE-FX
Version 1.0.3

2 WAGO ETHERNET Accessories 852
852-103 Industrial Switch
Manual
Version 1.0.3
© 2020 WAGO Kontakttechnik GmbH & Co. KG
All rights reserved.
WAGO Kontakttechnik GmbH & Co. KG
Hansastraße 27
D-32423 Minden
Phone: [phone] – 0
Fax: [phone] – 1 69
E-Mail: [e-mail]
Web: www.wago.com
Technical Support
Phone: [phone] – 4 45 55
Fax: [phone] – 84 45 55
E-Mail: [e-mail]
Every conceivable measure has been taken to ensure the accuracy and
completeness of this documentation. However, as errors can never be fully
excluded, we always appreciate any information or suggestions for improving the
documentation.
E-Mail: [e-mail]
We wish to point out that the software and hardware terms as well as the
trademarks of companies used and/or mentioned in the present manual are
generally protected by trademark or patent.
WAGO is a registered trademark of WAGO Verwaltungsgesellschaft mbH.

WAGO ETHERNET Accessories 852 Table of Contents 3
852-103 Industrial Switch
Manual
Version 1.0.3
Table of Contents
1Notes about this Documentation .............................................................5
1.1 Validity of this Documentation.................................................................5
1.2 Copyright................................................................................................5
1.3 Symbols .................................................................................................6
1.4 Number Notation ....................................................................................8
1.5 Font Conventions ...................................................................................8
2Important Notes.........................................................................................9
2.1 Legal Bases............................................................................................9
2.1.1 Subject to Changes............................................................................9
2.1.2 Personnel Qualification ......................................................................9
2.1.3 Proper Use of the Industrial Switches.................................................9
2.1.4 Technical Condition of Specified Devices.........................................10
2.1.5 Standards and Regulations for Operating the Industrial Switches ....10
2.2 Safety Advice (Precautions)..................................................................11
2.3 Special Use Conditions for ETHERNET Devices..................................13
3General ....................................................................................................14
3.1 Package Contents ................................................................................14
3.2 Industrial ETHERNET Technology........................................................14
3.3 Switching Technology...........................................................................14
3.4 Autonegotiation ....................................................................................15
3.5 Functioning of Switches........................................................................15
3.6 Port Speed & Duplex Mode ..................................................................15
4Device Description..................................................................................16
4.1 View .....................................................................................................17
4.1.1 Front View........................................................................................17
4.1.2 Top View..........................................................................................18
4.2 Connectors...........................................................................................19
4.2.1 Grounding screw..............................................................................19
4.2.2 Power Input (PWR/RPS)..................................................................19
4.2.3 Network Connection.........................................................................21
4.2.3.1 100BASE-FX Ports......................................................................21
4.2.3.2 10/100BASE-TX Ports.................................................................22
4.3 Display Elements..................................................................................23
4.3.1 Device LEDs ....................................................................................23
4.3.2 Port LEDs ........................................................................................24
4.4 Operating Elements..............................................................................25
4.4.1 DIP Switches....................................................................................25
4.5 Technical Data .....................................................................................27
4.5.1 Device Data .....................................................................................27
4.5.2 System Data ....................................................................................27
4.5.3 Power Supply...................................................................................27
4.5.4 Communication ................................................................................27
4.5.5 Environmental Conditions ................................................................28
4.6 Approvals .............................................................................................29
5Mounting..................................................................................................30

4 Table of Contents WAGO ETHERNET Accessories 852
852-103 Industrial Switch
Manual
Version 1.0.3
5.1 Installation ............................................................................................30
5.2 Installation on a Carrier Rail..................................................................30
5.3 Removal from Carrier ail.......................................................................30
6Connect Devices .....................................................................................31
6.1 Power Supply .......................................................................................31
6.2 External Alarm Contact Connection......................................................32
7Appendix..................................................................................................33
7.1 RJ-45 Cables........................................................................................33
List of Figures ..................................................................................................34
List of Tables....................................................................................................35

WAGO ETHERNET Accessories 852 Notes about this Documentation 5
852-103 Industrial Switch
Manual
Version 1.0.3
1 Notes about this Documentation
Always retain this documentation!
This documentation is part of the product. Therefore, retain the documentation
during the entire service life of the product. Pass on the documentation to any
subsequent user. In addition, ensure that any supplement to this documentation
is included, if necessary.
1.1 Validity of this Documentation
This documentation is only applicable to WAGO ETHERNET accessory products
“Industrial Switch” (852-103).
1.2 Copyright
This Manual, including all figures and illustrations, is copyright-protected. Any
further use of this Manual by third parties that violate pertinent copyright
provisions is prohibited. Reproduction, translation, electronic and phototechnical
filing/archiving (e.g., photocopying) as well as any amendments require the
written consent of WAGO Kontakttechnik GmbH & Co. KG, Minden, Germany.
Non-observance will involve the right to assert damage claims.

6 Notes about this Documentation WAGO ETHERNET Accessories 852
852-103 Industrial Switch
Manual
Version 1.0.3
1.3 Symbols
Personal Injury!
Indicates a high-risk, imminently hazardous situation which, if not avoided, will
result in death or serious injury.
Personal Injury Caused by Electric Current!
Indicates a high-risk, imminently hazardous situation which, if not avoided, will
result in death or serious injury.
Personal Injury!
Indicates a moderate-risk, potentially hazardous situation which, if not avoided,
could result in death or serious injury.
Personal Injury!
Indicates a low-risk, potentially hazardous situation which, if not avoided, may
result in minor or moderate injury.
Damage to Property!
Indicates a potentially hazardous situation which, if not avoided, may result in
damage to property.
Damage to Property Caused by Electrostatic Discharge (ESD)!
Indicates a potentially hazardous situation which, if not avoided, may result in
damage to property.
Important Note!
Indicates a potential malfunction which, if not avoided, however, will not result in
damage to property.

WAGO ETHERNET Accessories 852 Notes about this Documentation 7
852-103 Industrial Switch
Manual
Version 1.0.3
Additional Information:
Refers to additional information which is not an integral part of this
documentation (e.g., the Internet).

8 Notes about this Documentation WAGO ETHERNET Accessories 852
852-103 Industrial Switch
Manual
Version 1.0.3
1.4 Number Notation
Table 1: Number Notation
Number Code
Example
Note
Decimal
100
Normal notation
Hexadecimal
0x64
C notation
Binary
'100'
'0110.0100'
In quotation marks, nibble separated
with dots (.)
1.5 Font Conventions
Table 2: Font Conventions
Font Type
Indicates
italic
Names of paths and data files are marked in italic-type.
e.g.: C:\Program Files\WAGO Software
Menu
Menu items are marked in bold letters.
e.g.:
Save
>
A greater-than sign between two names means the selection of a
menu item from a menu.
e.g.: File > New
Input
Designation of input or optional fields are marked in bold letters,
e.g.:
Start of measurement range
“Value”
Input or selective values are marked in inverted commas.
e.g.: Enter the value “4 mA” under
Start of measurement range
.
[Button]
Pushbuttons in dialog boxes are marked with bold letters in square
brackets.
e.g.: [Input]
[Key]
Keys are marked with bold letters in square brackets.
e.g.: [F5]

WAGO ETHERNET Accessories 852 Important Notes 9
852-103 Industrial Switch
Manual
Version 1.0.3
2 Important Notes
This section includes an overall summary of the most important safety
requirements and notes that are mentioned in each individual section. To protect
your health and prevent damage to devices as well, it is imperative to read and
carefully follow the safety guidelines.
2.1 Legal Bases
2.1.1 Subject to Changes
WAGO Kontakttechnik GmbH & Co. KG reserves the right to provide for any
alterations or modifications. WAGO Kontakttechnik GmbH & Co. KG owns all
rights arising from the granting of patents or from the legal protection of utility
patents. Third-party products are always mentioned without any reference to
patent rights. Thus, the existence of such rights cannot be excluded.
2.1.2 Personnel Qualification
All sequences implemented on Series 852 devices may only be carried out by
electrical specialists with sufficient knowledge in automation. The specialists must
be familiar with the current norms and guidelines for the devices and automated
environments.
All changes to the controller should always be carried out by qualified personnel
with sufficient sufficient skills in PLC programming.
2.1.3 Proper Use of the Industrial Switches
The device is designed for the IP30 protection class. It is protected against the
insertion of solid items and solid impurities up to 2.5 mm in diameter, but not
against water penetration. Unless otherwise specified, the device must not be
operated in wet and dusty environments.

10 Important Notes WAGO ETHERNET Accessories 852
852-103 Industrial Switch
Manual
Version 1.0.3
2.1.4 Technical Condition of Specified Devices
The devices to be supplied ex works are equipped with hardware and software
configurations, which meet the individual application requirements. These
modules contain no parts that can be serviced or repaired by the user. The
following actions will result in the exclusion of liability on the part of WAGO
Kontakttechnik GmbH & Co. KG:
• Repairs,
• Changes to the hardware or software that are not described in the
operating instructions,
• Improper use of the components.
Further details are given in the contractual agreements. Please send your
request for modified and new hardware or software configurations directly to
WAGO Kontakttechnik GmbH & Co. KG.
2.1.5 Standards and Regulations for Operating the Industrial
Switches
Please observe the standards and regulations that are relevant to installation:
• The data and power lines must be connected and installed in compliance
with the standards to avoid failures on your installation and eliminate any
danger to personnel.
• For installation, startup, maintenance and repair, please observe the
accident prevention regulations of your machine (e.g., DGUV Regulation
“Electrical Installations and Equipment”).
• Emergency stop functions and equipment must not be deactivated or
otherwise made ineffective. See relevant standards (e.g., EN 418).
• Your installation must be equipped in accordance to the EMC guidelines so
electromagnetic interferences can be eliminated.
• Please observe the safety measures against electrostatic discharge
according to EN 61340-5-1/-3. When handling the modules, ensure that
environmental factors (persons, workplace and packing) are well grounded.
• The relevant valid and applicable standards and guidelines regarding the
installation of switch cabinets must be observed.

WAGO ETHERNET Accessories 852 Important Notes 11
852-103 Industrial Switch
Manual
Version 1.0.3
2.2 Safety Advice (Precautions)
For installing and operating purposes of the relevant device to your system the
following safety precautions shall be observed:
Do not work on devices while energized!
All power sources to the device shall be switched off prior to performing any
installation, repair or maintenance work.
Only install in appropriate housings, cabinets or electrical operation
rooms!
WAGO's 852 Series ETHERNET Switches are considered exposed operating
components. Therefore, only install these switches in lockable housings, cabinets
or electrical operation rooms. Access must be limited to authorized, qualified staff
having the appropriate key or tool.
Ensure a standard connection!
To minimize any hazardous situations resulting in personal injury or to avoid
failures in your system, the data and power supply lines shall be installed
according to standards, with careful attention given to ensuring the correct
terminal assignment. Always adhere to the EMC directives applicable to your
application.
Do not use in telecommunication circuits!
Only use devices equipped with ETHERNET or RJ-45 connectors in LANs.
Never connect these devices with telecommunication networks.
Replace defective or damaged devices!
Replace defective or damaged device/module (e.g., in the event of deformed
contacts).

12 Important Notes WAGO ETHERNET Accessories 852
852-103 Industrial Switch
Manual
Version 1.0.3
Protect the components against materials having seeping and insulating
properties!
The components are not resistant to materials having seeping and insulating
properties such as: aerosols, silicones and triglycerides (found in some hand
creams). If you cannot exclude that such materials will appear in the component
environment, then install the components in an enclosure being resistant to the
above-mentioned materials. Clean tools and materials are imperative for
handling devices/modules.
Clean only with permitted materials!
Clean housing and soiled contacts with propanol.
Do not use any contact spray!
Do not use any contact spray. The spray may impair contact area functionality in
connection with contamination.
Do not reverse the polarity of connection lines!
Avoid reverse polarity of data and power supply lines, as this may damage the
devices involved.
Avoid electrostatic discharge!
The devices are equipped with electronic components that may be destroyed by
electrostatic discharge when touched. Please observe the safety precautions
against electrostatic discharge per DIN EN 61340-5-1/-3. When handling the
devices, please ensure that environmental factors (personnel, work space and
packaging) are properly grounded.

WAGO ETHERNET Accessories 852 Important Notes 13
852-103 Industrial Switch
Manual
Version 1.0.3
2.3 Special Use Conditions for ETHERNET Devices
If not otherwise specified, ETHERNET devices are intended for use on local
networks. Please note the following when using ETHERNET devices in your
system:
• Do not connect control components and control networks directly to an
open network such as the Internet or an office network. WAGO
recommends putting control components and control networks behind a
firewall.
• Limit physical and electronic access to all automation components to
authorized personnel only.
• Change the default passwords before first use! This will reduce the risk of
unauthorized access to your system.
• Regularly change the passwords used! This will reduce the risk of
unauthorized access to your system.
• If remote access to control components and control networks is required,
use a Virtual Private Network (VPN).
• Regularly perform threat analyses. You can check whether the measures
taken meet your security requirements.
• Use “defense-in-depth” mechanisms in your system's security configuration
to restrict the access to and control of individual products and networks.

14 General WAGO ETHERNET Accessories 852
852-103 Industrial Switch
Manual
Version 1.0.3
3 General
3.1 Package Contents
• One Industrial Switch
• DIN rail bracket
• Protective caps for unused ports
3.2 Industrial ETHERNET Technology
The line of switches from WAGO ensure the scalability of your network
infrastructure with outstanding electrical and mechanical characteristics. These
robust devices are designed for industrial use and they are fully compliant with
IEEE 802.3, 802.3u.
They have function monitoring and redundant voltage supply with a supply
voltage range of 9 … 48 V. Alarm functions are enabled via DIP switch.
Characteristics such as auto negotiation and auto MDI/MDIX (crossover) on all
10/100BASE-TX ports are also realized, as is a store-and-forward switching
mode.
3.3 Switching Technology
Industrial ETHERNET primarily uses switching technology. This technology
allows any network subscriber to send at any time because the subscriber always
has an open peer-to-peer connection to the next switch. The connection is
bidirectional, i.e., the subscriber can send and receive at the same time (full
duplex).
The targeted use of switching technology can increase real-time capability
because the peer-to-peer connection prevents collisions in network
communication.

WAGO ETHERNET Accessories 852 General 15
852-103 Industrial Switch
Manual
Version 1.0.3
3.4 Autonegotiation
Autonegotiation allows the switch to detect the transmission rate and operating
mode for each port and the connected subscriber or subscribers, and to set them
automatically. The highest possible mode (transmission speed and operating
mode) is set.
Autonegotiation is available to ETHERNET subscribers connected to the switch
via copper cable.
This make the switch a plug-and-play device.
3.5 Functioning of Switches
Switches analyze all incoming data packages and forward them to the port where
the corresponding destination address is located. Exceptions are the multicast
and broadcast telegrams, which are forwarded to all active ports of the switch.
For selective forwarding of the telegrams, each switch contains of an address /
port assignment table in which the assignments of the destination addresses to a
specific port of the switch are stored. The address / port mapping table is typically
generated and maintained automatically by the switch through a self-learning
process. Incoming data packages are analyzed, filtered and forwarded directly to
the appropriate port by using this assignment table based on their destination
address. The incoming data package is sent to all ports, if there is no
corresponding entry in the assignment table for a destination address. If a
destination address answers, the assignment table is complemented with this
destination address as well as the associated port.
3.6 Port Speed & Duplex Mode
After a cable is plugged into a specific port, the system uses auto negotiation to
determine the transmission mode for the new twisted pair connection:
If the connected device does not support auto negotiation or has auto negotiation
disabled, an auto sensing process is initiated to select the speed and set the
duplex mode to half duplex.

16 Device Description WAGO ETHERNET Accessories 852
852-103 Industrial Switch
Manual
Version 1.0.3
4 Device Description
The 852-103 Industrial Switch is an 8-port 10/100BASE-TX with dual SFP
100Base-FX port (SFP modules are optional) ETHERNET switch. The switch has
a rugged housing, a redundant power supply and function monitoring with relay,
making it ideal for a wide range of applications.
Other key features are:
• Eight (8) 10/100BASE-TX and Two (2) 100BASE-FX (SFP-type fiber
transceivers)
• Rugged metal-IP30 case
• Vibration/Shock operational
• Wide voltage range: 9 … 48 V
• DIP switch to enable or disable alarm functions
• Power input polarity protection function
• Auto negotiation at all copper ports

WAGO ETHERNET Accessories 852 Device Description 17
852-103 Industrial Switch
Manual
Version 1.0.3
4.1 View
4.1.1 Front View
Figure 1: Front View of the Industrial Switch
Table 3: Legend for Figure “Front View of the Industrial Switch”
Pos.
Descrip-
tion
Meaning Details see Section
1 PWR Status LED Power Supply
“Device Description” >
“Display Elements”
2 RPS Status LED Redundant Voltage Supply
“Device Description” >
“Display Elements”
3 ALM Status LED Alarm
“Device Description” >
“Display Elements”
4 -
Status LED TX-Port 100 Mbit/s
(1 LED for each port)
“Device Description” >
“Display Elements”
5 -
Status LED TX-Port LNK/ACT
(1 LED for each port)
“Device Description” >
“Display Elements”
6 - Port 8 x RJ-45 (10/100BASE-TX-Ports)
“Device Description” > “
Connectors”
7 - Port 2 x SFP (100BASE-FX, fiber optic)
"Device Description" >
"Connections"

18 Device Description WAGO ETHERNET Accessories 852
852-103 Industrial Switch
Manual
Version 1.0.3
Table 3: Legend for Figure “Front View of the Industrial Switch”
Pos.
Descrip-
tion
Meaning Details see Section
8 OFFLINE
Status LED 100 Mbit/s for fiber optic port, port
offline (2)
“Device Description” >
“Display Elements”
9 LNK/ACT Status LED, LNK/ACT for fiber optic port (2)
“Device Description” >
“Display Elements”
10 100 Status LED, 100 Mbit/s for fiber optic port (2)
“Device Description” >
“Display Elements”
4.1.2 Top View
Figure 2: Top View of the Industrial Switch
Table 4: Legend for Figure “Top View of the Industrial Switch”
Pos.
Descrip-
tion
Meaning Details see Section
1
-
Grounding screw
-
2 -
Terminal block (male connector) for power supply
(PWR/RPS/ALM) and potential free alarm contact
“Device Description” > “
Connectors”
3 - DIP switches
“Device Description” >
„Operating elements“

WAGO ETHERNET Accessories 852 Device Description 19
852-103 Industrial Switch
Manual
Version 1.0.3
4.2 Connectors
4.2.1 Grounding screw
The switch must be grounded. Connect the grounding screw to the ground
potential. Do not operate the switch without an appropriately installed protective
earth conductor.
Figure 3: Grounding screw
4.2.2 Power Input (PWR/RPS)
The female connector (Item No. 2231-106/026-000) can easily be connected to
the 6-pole male connector located on the top of the switch.
The male connector shows the following pin assignment:
Abbildung 4: Power Supply (PWR/RPS)
Table 5: Legend for Figure “Power Supply (PWR/RPS)”
Connection
Description
Description
+
PWR
Primary DC input
-
PWR
Primary DC input
+
RPS
Secondary DC input
-
RPS
Secondary DC input
ALM
Contact for external alarm
ALM
Contact for external alarm

20 Device Description WAGO ETHERNET Accessories 852
852-103 Industrial Switch
Manual
Version 1.0.3
Warning of damage to equipment by electrostatic discharge
DC Powered Switch: Power is supplied through an external DC power source.
Since the switch does not include a power switch, plugging its power adapter into
a power outlet will immediately power it on.