Walker Edison BLWS User manual

ITEM#: BLWS
Assembly Instructions
  
 
Revised 03/2017
Copyright © 2010, by Walker Edison Furniture Co., LLC. All rights reserved. P.1
(Work station and assembly instructions for both twin
size (BTOL) & full size (BDOL) loft bed work station)

Copyright © 2010, by Walker Edison Furniture Co., LLC. All rights reserved.

Copyright © 2010, by Walker Edison Furniture Co., LLC. All rights reserved.

Copyright © 2010, by Walker Edison Furniture Co., LLC. All rights reserved.

Copyright © 2010, by Walker Edison Furniture Co., LLC. All rights reserved.

Copyright © 2010, by Walker Edison Furniture Co., LLC. All rights reserved.
Remove the bolts, washers and plastic plugs shown above from the bunk bed frame.

Copyright © 2010, by Walker Edison Furniture Co., LLC. All rights reserved.
Remove the long crossbar from the bunk bed frame and turn it over so the screw holes are
facing forward. Reattach the long crossbar to the bunk bed frame using the bolts and
washers from Step 1. Loosen, but do not remove the bolts that anchor the short crossbars to
the bunk bed frame.

Copyright © 2010, by Walker Edison Furniture Co., LLC. All rights reserved.
Attach angle brackets (E) to crossbars (1,2) using medium bolts (A) and washers (B).

Copyright © 2010, by Walker Edison Furniture Co., LLC. All rights reserved.
Attach crossbars (1,2) to the bunk bed frame using medium bolts (A) and washers (B).
Retighten the bolts that secure the short crossbars.

Copyright © 2010, by Walker Edison Furniture Co., LLC. All rights reserved.
Attach crossbar (3) to the bunk bed frame using large bolts (C) and washers (B).

Copyright © 2010, by Walker Edison Furniture Co., LLC. All rights reserved.
Attach angle brackets (E) to crossbars (14,15) using medium bolts (A) and washers (B).

Copyright © 2010, by Walker Edison Furniture Co., LLC. All rights reserved.
Attach crossbars (14,15) to the bunk bed frame using medium bolts (A) and washers (B).
Retighten the bolts that secure the short crossbars.

Copyright © 2010, by Walker Edison Furniture Co., LLC. All rights reserved.
Attach crossbar (3) to the bunk bed frame using large bolts (C) and washers (B).

Copyright © 2010, by Walker Edison Furniture Co., LLC. All rights reserved.
Attach shelf racks (5L,5R) to shelf crossbar (6) using large bolts (C). Build each shelf by
attaching shelf supports (7,8) to shelf top (9) using small bolts (D) and washers (B).

Copyright © 2010, by Walker Edison Furniture Co., LLC. All rights reserved.
Attach the assembled shelves from Step 6 to shelf racks (5L,5R) by inserting them in at the
desired height and gently pushing down to lock in place.

Copyright © 2010, by Walker Edison Furniture Co., LLC. All rights reserved.
Attach the shelf assembly from Step 7 to the bunk bed frame using extra-large bolts (H) and
washers (B).

Copyright © 2010, by Walker Edison Furniture Co., LLC. All rights reserved.
Attach desk crossbars (4) to the bunk bed frame using medium bolts (A).

Copyright © 2010, by Walker Edison Furniture Co., LLC. All rights reserved.
Attach keyboard sliders (10,11) to keyboard tray (12) using small screws (J).

Copyright © 2010, by Walker Edison Furniture Co., LLC. All rights reserved.
Attach the keyboard assembly from Step 10 to crossbars (4) using small bolts (D) and
washers (B).

Copyright © 2010, by Walker Edison Furniture Co., LLC. All rights reserved.
Attach the desk top (13) to the bunk bed frame using medium screws (G) on either end,
and large screws (F) at the keyboard tray assembly.