Walker Edison BQATT User manual

Revised 10/2020
Item #:
BQATT

Parts List
Part 1: Headboard Panel
Part 2: Slat Set (7 slats)
Part 3: Side Rail
Part 4: Down Rail
Part 5: Cross Bar
Part 6: Up Rail
Part 7: Legs
Part 8: Headboard Lefth Feet
Part 9: Headboard Rigth Feet
Part 10: Footboard Lefth Feet
Part 11: Footboard Rigth Feet
Part 12: Slat Set (6 slats)
12
01
02
0303
04
05
06
07
08
09
10
11
0303
06
06
04
07
02
12

10x40 mm Wood dowel 08 pçs
08x40 mm Wood dowel 16 pçs
A
B
Ruler- Use this ruler to help correctly identify the screws
0510 15 20 25 30 35 40 45 50 55 60 65 70 75 80 85 90 95 100 105 110 115 120 125 130 135 140 145 150 155 160 165 170
1/4"x70 mm Headless bolt 20 pçs
C
Washer 20 pçs
D
Nut 22 pçs
E
Hex Key 01 pçs
F
Spanner 01 pçs
G
3,5x35mm Screw 24 pçs
H
4,0x16mm Screw 08 pçs
I
Metal Support 02 pçs
J
7,0x50mm Bolt 04 pçs
K
1/4"x40mm Bolt 02 pçs
L

Step 1
Step 2
Insert wood dowels (A) into parts (03 and 04).
P.5
A
A
A
A
A
A
A
A
A
B
B
B
B
B
BB
BB
B
B
B
B
B
B
B
B
Insert wood dowels (B) into parts (01 and 06).
A
0303
04
0303
04
B
01
06
06
06

Step 3
P.6
Insert Headless (C) into parts (08,09,10 and 11).
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
08 09
10
11

Step 4
P.7
PLEASE , Check the holes position
CAREFULLY
PLEASE , Check the holes position
CAREFULLY
Assemble the parts 06, 01 and 04 on the feet 08 and 09.
Step 5
01
04
06
08
09
06
Insert washer (D) and nut (E) as in the picture. After use Spanner (G) to
tighten. Repeat the same process at both sides.
E
G
D
E
D
G
D
E
G

Step 6
P.8
Rotate the Headboard 180 degrees.
Step 7
Insert washer (D) and nut (E) as in the picture. After use Spanner (G) to
tighten. Repeat the same process at both sides.
D
E
G
D
D
E
G

Step 8
Step 9
P.9
PLEASE , Check the holes position
CAREFULLY
PLEASE , Check the holes position
CAREFULLY
Assemble the parts 06 and 04 on the feet 10 and 11.
Insert washer (D) and nut (E) as in the picture. After use Spanner (G) to
tighten. Repeat the same process at both sides.
D
E
G
D
04
06
10
11
D
E
G

Step 10
P.10
IJ
I
I
I
Use screews (I) to fix (J) hardware.
Repeat this process at two parts.
F
K
K
Attach central support 05 to feet 07 using wood joint connectors (K).
05
07
50mm
16mm
J
I
K
F
07
Step 11