Walker Edison BTLD46SP User manual

Assembly Instructions

Instruction Manual
IMPORTANT INFORMATION
READ BEFORE ASSEMBLING THIS PRODUCT
Follow the information on the warning labels found on the bunk bed and on the packaging. Do not
remove the warning labels from the bed.
Use only a mattress with the dimensions 74-75 in.L x 37.5-38.5 in.W x 6 in.H on the upper bunk.
The surface of the mattress must be at least 5 in. (127mm) below the upper edge of the guardrails.
Mattress must not exceed the maximum thickness of 6 in.
Always use the recommended size of mattress or mattress support, or both, to help prevent the
likelihood of entrapment or falls.
The use of a water or sleep flotation mattress is prohibited.
DO NOT use substitute parts. Contact the manufacturer or dealer for replacement parts.
Always use guardrails on the upper bunk. If the bunk bed will by placed next to a wall, the guardrail
running the full length of the bed should by placed against the wall to prevent entrapment between
the bed and the wall.
Periodically check that the guardrails, ladders and other components of the bed are in their proper
position, free from damage and that all connectors are tight.
Always use the ladder to access the upper bunk.
DO NOT allow children under 6 years of age to use the upper bunk.
DO NOT allow horseplay on or under the bed. Prohibit jumping on the bed.
Prohibit more than one person on the upper bunk.
The use of a night light may provide an added safety precaution for a child using the upper bunk.
STRANGULATION HAZARD – Never attach or hang items to any part of the bunk bed that are not
designed for use with the bed; including but not limited to hooks, belts and jump ropes.
Keep these instructions for future reference.

Parts List

Hardware List

Assembly Options
Option A - Ladder Left
To build this option follow Steps 1-8, Steps
10A-13A and Steps 14-23. Skip Step 9 for
this assembly option.
Option B - Ladder Right
To build this option follow Steps 1-8, Step 9,
Steps 10B-13B and Steps 14-23.

Attach guardrail (10) and shelf supports (8) to posts (1,4) using bolts (A). Tighten bolts (A) with wrench (G).
Please note the position of all pre-drilled holes as shown above before attaching bed parts together.
Attach second guardrail (10) posts (2,3) using bolts (A). Tighten bolts (A) with wrench (G). Please note the
position of all pre-drilled holes as shown above before attaching bed parts together.

Attach crossbar (5) to post (1) and crossbar (6) to post (4) using bolts (A). Tighten bolts (A) with wrench (G).
Please note the position of all pre-drilled holes as shown above before attaching bed parts together.
Attach opposite end of crossbar (5) to post (2) and opposite end of crossbar (6) to post (3) using bolts (A).
Tighten bolts (A) with wrench (G).

Roll mattress support slats (11) out along the bed frame and secure them to the bed frame using anchors (F)
and bolts (A) where indicated above. Bolts (A) will screw directly into crossbars (5,6). Tighten bolts (A) with
wrench (G).
Attach guardrail (9) to posts (3,4) using bolts (A). Secure guardrail (9) to crossbar (6) using bolts (B). Tighten
bolts (A,B) with wrench (G).

Attach second guardrail (9) to posts (1,2) using bolts (A). Secure guardrail (9) to crossbar (5) using bolts (B).
Tighten bolts (A,B) with wrench (G).
Attach shelf supports (12) to rails (7) using bolts (A). Tighten bolts (A) with wrench (G).

Attach ladder rungs (13) to post (1) using bolts (A). Tighten bolts (A) with wrench (G).
Attach the shelf support assembly from Step 7 to ladder rungs (13) using bolts (B). Rail (7) will attach directly
to ladder rungs (13). Tighten bolts (B) with wrench (G).