Walker Edison D51Z29 User manual

Assembly Diagram
Model No. D51Z29
1
For our most up to date assembly instructions or to request missing, lost, or broken parts, or for any other
customer service issue, please visit our website at www.walkeredison.com or call us toll free at 877-207-5906.
Important
*Note: These parts come preassembled for shipping purposes and must be disassembled for assembly
1
wrench
A
B
C
D
E
F
G
H*
J
L
M
N
O
P
Q
R
S
T
small bolts 8
medium bolts
4
12
16
8
4
2
2
L = 1, R = 1
1
1
2
2
1
1
2
2
large bolts
rubber suction
cups
CPU feet
desk feet
keyboard tray
bracket
keyboard tray
arm
keyboard tray
support frame
middle glass
keyboard tray
glass
desk leg left
desk leg right
middle frame
keyboard tray
frame
K2
desk glass
U
V
1
CPU stand
2
4
lower back
cross bar
left upper cross
bar
right upper cross
bar
support wire
Component List
I*

2
Step 1
Step 2
Screw desk feet (F) into the bottom of
desk legs (N) and (O).
*Note: Be sure that you are using
the correct desk leg by verifying the
positioning of the holes as shown in
the illustration.
Assembly Diagram Model No. D51Z29Model No. D51Z29
For the left side of the desk, take leg (N) and screw in the medium bolts (D) into the left upper
cross bars (T). Take the lower back support bar (S) and screw it into leg (N) with medium bolts (D).

3
Attach lower back support bar (S) to leg (O) using medium bolt (D).
Assembly Diagram Model No. D51Z29Model No. D51Z29
Screw in keyboard support tray frame (J) between left upper cross bars (T) using medium bolts (D).
Attach middle frames (R) and cross bars (T) to leg (O) using large bolts (C).
For the right side of the desk, attach middle frame (R) to leg (N) and right upper cross bars (U) using
large bolts (C). Attach leg (N) to lower back support bar (S) using medium bolt (D).
Step 3
Step 4
Step 5
Attach leg (O) to right upper cross bars (U) using medium bolts (D). Attach leg (O) to lower back
support bar (S) with medium bolt (D).
Step 6
J

Assembly Diagram Model No. D51Z29
4
Step 7
Secure the support wire (V) into legs (O) and (N) by putting the end of the support wire which has
the small curve into the hole, as shown in the above circle. Now secure the other end of the support
wire (V) into the loop on the lower back cross bar (S). Repeat this step for the other three support
wires (V). *Note: You may need to unscrew support wire (V) hook for proper fitting.
To construct the keyboard tray you need to take the keyboard tray brackets (H) and secure them to the
keyboard frame (Q) using small bolts (B) as shown in the circle of the illustration.
Step 8
S
S
T
U
Disassemble the keyboard tray brackets (H) and the keyboard tray arm (I)
by pressing down the small lever and pulling up.
Step 9
H
I

Assembly Diagram Model No. D51Z29
5
Step 10
Push down on small
lever to allow keyboard
bracket to slide along
keyboard arm.
Locate your rubber suction cups (E) and secure them to the table by placing the small ends into the
holes on top of the desk frame.
Place rubber suction cups (E) on keyboard tray frame (Q) and place keyboard tray glass (M) on top
of the rubber suction cups.
Now secure keyboard tray arm (I) onto both sides of the keyboard tray support frame (J) using
small bolts (B). Ensure the open end of keyboard tray arm (I) faces front side of desk.
Step 11
Step 12
Now take the keyboard tray and slide it into the keyboard tray arm (I).
Place desk glass (K) and (L) on top of the desk frame according to the above
illustration.
Step 13
Step 14

Assembly Diagram Model No. D51Z29
6
Step 12
Final Assembly
P
G
GG
G
Find the CPU stand (P) and screw
in the CPU feet (G) into the under
side of the frame.
For our most up to date assembly instructions or to request missing, lost, or broken parts, or for any other customer
service issue, please visit our website at www.walkeredison.com or call us toll free at 877-207-5906.