Waring BB320 User manual

BB300
BB300 SERIES
INSTRUCTION MANUAL
MANUAL DE INSTRUCCIONES
DE LAS LICUADORAS DE LA SERIE BB300
DIRECTIVES D’UTILISATION
DES MÉLANGEURS DE LA SÉRIE BB300
For your safety and continued enjoyment of this product,
always read the instruction book carefully before using.
Para su seguridad y para disfrutar plenamente de este producto,
siempre lea las instrucciones cuidadosamente antes de usarlo.
An que cet appareil vous procure en toute sécurité beaucoup
de satisfaction, lire attentivement le mode d’emploi avant de l’utiliser.
BB320 BB340

2
IMPORTANT SAFEGUARDS
When using electrical appliances, basic safety precautions
should always be taken, including the following:
1. READ ALL INSTRUCTIONS.
2. Unplug from outlet when not in use, before putting
on or taking off parts, and before cleaning.
3. To protect against electrical hazards, do not immerse
the blender base in water or other liquids.
4. This appliance is not intended for use by persons
(including children) with reduced physical, sensory
or mental capabilities, or lack of experience and
knowledge, unless they have been given supervision
or instruction concerning use of the appliance by a
person responsible for their safety.
5. Children should be supervised to ensure that they
do not play with the appliance.
6. Avoid contact with moving parts.
7. Do not operate any appliance with a damaged cord or
plug or after the appliance malfunctions or is dropped
or damaged in any manner. Return appliance to the
nearest authorized service facility for examination,
repair or electrical or mechanical adjustment.
8. The use of attachments not recommended by the
appliance manufacturer may cause hazards.
9. Do not use outdoors.
10. Do not let cord hang over edge of table or counter,
where it can inadvertently be pulled on or tripped over,
or touch hot surfaces, which could damage the cord.
11. Keep hands and utensils out of container while
blending to prevent the possibility of severe personal
injury and/or damage to the blender. A rubber scraper
may be used, but must be used only when the blender
is not running.
12. Blades are SHARP. Handle carefully.

3
13. Never place cutting assembly or cutting blades on base
without container properly attached.
14. Always operate blender with cover in place.
15. Always operate blender with jar pad in place.
16. CAUTION:This blender is not intended for use with hot
liquids or ingredients.
17. Do not ll above MAX FILL line for blending.
18. Not for waterjet cleaning.
19. Ensure the jar coupler and motor coupler are aligned
and engaged before operating. If unable to engage,
remove jar and shake contents, then try again.
20. The jar coupler and motor coupler may be hot after
running; do not touch.
21. Replace jar pad if worn.
22. Always use HIGH speed for crushing ice.
23. If the jar overows during blending, there is too much
liquid/ingredients in the jar. Stop blending, remove
enough liquid/ingredients to below MAX FILL line, and
continue blending. Do not operate if overowing.
24. DO NOT use carbonated liquids in the blender jar or
any blending container. Using carbonated liquids in
the blender jar or any blending container may result in
injury.
25. DO NOT blend oil or oil-based products, such as
peanut butter, for more than 5 minutes.
26. Never remove blender jar from base unit until the blade
and coupling have completely stopped.
SAVE THESE INSTRUCTIONS

4
GROUNDING INSTRUCTIONS
• For your protection, Waring®Commercial Blenders are
equipped with a 3-conductor cord set.
• 120 volt units are supplied with a molded 3-prong,
grounding-type plug and should be used in combination
with a properly connected, grounding-type outlet, as
shown in Figure 1.
If a grounding-type outlet is not available, an adapter, shown
in Figure 2, may be obtained to enable a 2-slot wall outlet to
be used with a 3-prong plug.
Referring to Figure 3, the adapter must be grounded by
attaching its grounding lug under the screw of the outlet
cover plate.
CAUTION: Before using an adapter, it must be determined
that the outlet cover plate screw is properly grounded. If in
doubt, consult a licensed electrician.
Never use an adapter unless you are sure it is properly
grounded.
NOTE: Use of an adapter is not permitted in Canada.
BEFORE FIRST USE
Follow the cleaning and sanitizing instructions on page 8
before rst use and if you have not used your blender for a
period of time. Thoroughly dry the container before placing it
on the base.

5
BB300 OPERATION
1. With the switch in the OFF
position, place container
on blender base. Be sure
container is fully seated and
that drive coupling is properly
engaged. Plug blender cord
into outlet.
2. Put ingredients into jar and cover it. Do not ll above
MAX FILL line.
3. This blender has 2 speed settings: HIGH and LOW.
Press toggle switch to desired position. To crush ice,
always use HIGH speed setting.
4. When nished blending, set toggle switch to OFF
position.
5. This blender is equipped with a PULSE option. Hold
toggle switch in down position to engage PULSE
function. Unit will run on HIGH speed until the toggle
switch is released.
NOTE: This blender utilizes a Slow Start™feature. When
beginning HIGH or LOW operation, the unit will start in a
lower speed for 1 second and then switch to the full selected
speed. PULSE utilizes a .5-second Slow Start™. This allows
for a more even blending of ingredients in jar.
6. Allow motor to come to a complete stop before
removing container from blender base. Never place
the container on the motor base or remove it from
the motor base while motor is running.
7. Always hold container with one hand when starting and
while blending. Never operate without jar lid.
8. Wash and dry container after each use. See Cleaning
and Sanitizing Instructions.
9. Unplug to turn off all power to blender.

6
BB320 OPERATION
Follow steps 1–2 from BB300
instructions.
3. This blender is equipped
with an electronic membrane
keypad. The keypad has
HIGH, LOW, STOP, PULSE
and ON/OFF buttons. Always
use HIGH speed for crushing ice.
4. Press ON/OFF button; the blue LED light will turn on.
5. For continuous operation, press either the LOW or
HIGH button. When nished blending, press STOP. For
momentary operation, press the PULSE button; motor
will run on HIGH speed until the button is released.
NOTE: This blender utilizes a Slow Start™feature. When
beginning HIGH or LOW operation, the unit will start in a
lower speed for 1 second and then switch to the full selected
speed. PULSE utilizes a .5-second Slow Start™. This allows
for a more even blending of ingredients in jar.
6. Allow motor to come to a complete stop before
removing jar from blender base. Never place the
jar on the motor base or remove it from the motor
base while motor is running.
7. Always hold jar with one hand when starting and while
blending. Never operate without jar lid.
8. Wash and dry jar after each use. See Cleaning and
Sanitizing Instructions.
9. Unplug to turn off all power to blender.
BB340 OPERATION
Follow steps 1–2 from BB300 instructions.
3. This blender is equipped with an electronic membrane
keypad. The keypad has HIGH, LOW, STOP, PULSE
and ON/OFF buttons, as well as a 99-second

7
countdown timer with + and
– buttons. Always use HIGH
speed for crushing ice. The
blender can operate in two
modes: timer mode and
continuous mode.
4. For timer mode, press the ON/
OFF button. Press the + or –
button to set the desired time.
The electronic timer will indicate runtime in 1-second
intervals up to a maximum of 99 seconds. After the
desired time is set, press HIGH or LOW to start the
blender. The timer will count down to 0 in 1-second
intervals and blender will shut off. Pressing the PULSE
button or the STOP button will override the timer and
the blender will stop regardless of time left on timer.
5. If the STOP button is pressed, the timer function will
turn off and the unit will return to continuous mode. To
reactivate timer, press + or – button. When using the
electronic timer again, the initial time will be the last
time set. NOTE: If unit has been unplugged, the timer
will default back to 5 seconds.
6. For continuous operation, press either the LOW or
HIGH button when timer is not lit. If the timer is lit and
you want to use continuous mode, press the STOP
button and proceed. When nished blending, press
STOP. For momentary operation, press the PULSE
button. Motor will run on HIGH speed until the button is
released. Blue LED light will blink while in operation.
NOTE: This blender utilizes a Slow Start™feature. When
beginning HIGH or LOW operation, the unit will start in a
lower speed for 1 second and then switch to the full selected
speed. PULSE utilizes a .5-second Slow Start™. This allows
for a more even blending of ingredients in jar.
7. Allow motor to come to a complete stop before
removing container from blender base. Never place

8
the container on the motor base or remove it from
the motor base while motor is running.
8. Always hold jar with one hand when starting and while
blending. Never operate without jar lid.
9. Wash and dry jar after each use. See Cleaning and
Sanitizing Instructions.
10. Unplug to turn off all power to blender.
RESETTING THERMAL PROTECTION
• Your blender is equipped with a manual reset switch to
protect the motor from overheating.
• If your blender stops running under heavy use, press the
ON/OFF button and unplug the power cord. Empty the
blender jar of all its contents and allow approximately
5 to10 minutes for the motor to cool down.
• Plug the power cord back into the outlet and continue
blending.
• If your blender does not function properly following this
procedure, discontinue use and contact a certied Waring
Customer Service Center.
CLEANING AND SANITIZING INSTRUCTIONS
THE JAR MUST BE CLEANED AND DRIED AFTER EACH
USE OF THE BLENDER ACCORDING TO THE FOLLOWING
INSTRUCTIONS.
FAILURE TO DO SO MAY ALLOW RESIDUE OF
PROCESSED MATERIAL TO COLLECT ON THE INTERNAL
SEALS OF THE BLADE ASSEMBLY, RENDERING THEM
INEFFECTIVE.
• Wash, rinse, sanitize and dry jar prior to initial use and
whenever it will not be used again within a period of
1 hour.
• Wash and rinse container after each use.
• Clean and sanitize motor base prior to initial use and after
each use.

9
• Washing solutions based on non-sudsing detergents and
chlorine-based sanitizing solutions having a minimum
chlorine concentration of 100 PPM are recommended.
The following washing, rinsing, and sanitizing solutions, or
their equivalents, may be used.
• In repetitive batch-processing applications, frequent
cleaning of the jar will prolong the life of the blade
assembly. In no case should actual running time between
cleanings exceed one-half hour.
• Do not use jar to store processed foods or beverages.
TO WASH AND RINSE JAR
1. REMOVE JAR FROM MOTOR BASE. Remove lid.
Rinse jar interior and lid under running water. Add
washing solution to jar. Scrub and ush out the jar
interior to dislodge and remove as much food residue
as possible. Empty jar.
2. Wipe down exterior of jar with a soft cloth or sponge
dampened with washing solution. Wash lid and lid
insert in fresh washing solution. Fill jar one-quarter full
with fresh washing solution, cover (with lid only), place
on motor base and run on HIGH speed for two (2)
minutes. Empty jar.
3. Repeat step (2) using clean rinse water in place of
washing solution.
SOLUTION PRODUCT DILUTION IN
WATER
TEMPERATURE
Washing Diversey Wyandotte
Diversol®BX/A or CX/A
4 Tablespoons/Gallon Hot 115˚F ( 46˚C )
Rinsing Plain Water Warm 95˚F (35˚C)
Sanitizing Clorox® Institutional
Bleach
1 Tablespoon/Gallon Cold 50˚F–70˚F
(10˚C–21˚C)

10
IMPORTANT
NOTE: IN ORDER TO MINIMIZE POSSIBILITY OF
SCALDING, TEMPERATURE OF WASHING SOLUTION
AND RINSE WATER MUST NOT EXCEED 115˚F (46˚C),
AND QUANTITY USED MUST NOT EXCEED ONE-
QUARTER JAR FULL.
TO SANITIZE AND DRY CONTAINER
1. Wipe down exterior of jar with a soft cloth
or sponge dampened with sanitizing solution.
2. Fill jar with sanitizing solution, cover, place on motor
base, and run on HIGH speed for one (1) minute. Empty
jar. Dislodge any residual moisture from blade assembly
by placing empty jar on motor base and running on
HIGH speed for two (2) seconds.
3. Sanitize lid and lid insert by immersing in sanitizing
solution for two (2) minutes.
4. Do not rinse jar, lid, or lid insert after sanitizing
is completed. Allow parts to air-dry.
TO CLEAN AND SANITIZE MOTOR BASE
1. UNPLUG POWER CORD. Wipe down exterior surfaces
of motor base with soft cloths or sponges dampened
with washing solution, rinse water, and sanitizing
solution. Prevent liquid from running into motor base
by wringing all excess moisture from cloths or sponges
before using them.
DO NOT IMMERSE MOTOR BASE IN WASHING SOLUTION,
RINSE WATER OR SANITIZING SOLUTION.
2. Allow motor base to air-dry before using.
SERVICE
Refer to the list of Authorized Service Centers enclosed
with your Waring®Commercial Blender or visit
waringcommercialproducts.com for a ZIP code search.