Wasp N1181 Operating instructions

Please Read
Note:
The Wasp CCD Scanner is ready to scan the most popular
bar codes out of the box. This manual should only be
used to make changes in the configuration of the
scanner for specific applications. This scanner does not
require software or drivers to operate.The scanner enters
data as keyboard data. Please review this manual before
scanning any of the programming bar codes in this manual.
Tech Tip
If you are unsure of the scanner configuration or have
scanned the incorrect codes, please scan the default
bar code on page 6.This will reset the scanner to its
factory settings.
CCD Programming Guide
for Wasp Bar Code CCD Scanner

© Copyright Wasp Technologies
All rights reserved.
Version 2.0
No part of this publication may be reproduced or transmitted in any
form or by any means without the written permission of Wasp
Technologies.The information contained in this document is subject
to change without notice.
Wasp is a trademark ofWasp Technologies. All other trademarks or registered trademarks are the
property of their respective owners.

Table of Contents
Chapter 1. Introduction..............................................................................1
Chapter 2. Installation................................................................................2
Chapter 3. Quick Start ..............................................................................3
Chapter 4. Bar Code Symbologies............................................................4
Chapter 5. CCD Setup & Configuration ..............................................5-19
1. Set Default..............................................................6
2. Preamble/Postamble ..............................................7
3. CCD Audio Configuration........................................8
4. Keyboard Setting ....................................................9
5. CCD Scanning Control ........................................10
6. Enable Bar Code Symbologies........................11-12
7. Code 39................................................................13
10. Interleaved 2 of 5..................................................14
11. Codabar................................................................15
12. UPC-A ..................................................................16
13. UPC-E ..................................................................17
14. EAN/JAN-13..........................................................18
15. EAN/JAN-8............................................................19
Appendix A. Bar Code Test Symbols....................................................20-22
Appendix B. Preamble/Postamble AdditionTable ................................23-25
Appendix B. Preamble/Postamble Special Characters..............................26
Appendix C. Additional Scanner Functions................................................27
Product Support ..............................................................................................28
Warranty ..............................................................................................28

1
Chapter 1
Introduction
Bar coding is the most common Automated Data Collection (ADC) technology
providing timely, error-free information that can be used to increase productivity,
accuracy, and efficiency in the workplace. Virtually every type of industry is
using bar codes to replace keyboard data entry. Studies have shown that a
proficient data entry operator will make one error for every 300 characters that
are manually entered. The error rate using bar codes is almost negligible and
can be error-free using bar code symbologies with the check digit enabled.
The Wasp Charged Coupled Device (CCD) technology is a technique whereby a
bar code is photographed, digitized, and electronically sampled by built-in
photodetectors. The detectors process the measurement of every bar and
space using the number of adjacent photodetectors which contrast a black mark
and a white space. TheWasp CCD is extremely rugged since it has no moving
parts. The Wasp CCD reader supports PC AT/XT and PS/2 keyboard interfaces
and easily wedges between the computer and keyboard. Bar code data is
passed directly into the keyboard buffer as if it had been typed in by hand by a
data entry operator.
Of all the hand held, bar code scanning devices on the market, the CCD reader
is the easiest to use and most cost effective for the typical business user. The
Wasp CCD scanner is a one touch scanner allowing the user to come in direct
contact with the bar code.It also supports a depth of reading of up to 1.4 inches
to successfully decode a bar code symbology.Bar codes up to 2.75 inches in
length can be scanned. To activate the scanner, the user simply covers the bar
code with head of the scanner and pulls the trigger. The Wasp CCD supports a
scan rate of 50 scans per second.

2
Chapter 2
Installation
1. Turn off your computer.
2. Plug the keyboard wedge cable into the handle of the CCD reader.
3. Unplug your PC keyboard cable and plug the male end (Din 5) of the Wasp
CCD scanner directly into your PC keyboard port. Plug your keyboard
cable into the other end (female Din 5) of the the Wasp CCD scanner. If
your keyboard and PC support a Din 6 connection, use the enclosed Din 5
to Din 6 converter cables.
4. Turn your computer on.
Note: Make sure scanner is not plugged into the mouse port. Scanner will
not function properly if plugged into the mouse port.
Side View
Scan Feedback Indicator
Trigger
Scanning Aperture
Scanning
Aperture
Trigger
Keyboard Wedge Cable
Keyboard
Y-Cable
Bottom View
Din-6
Din-5
(PC Only)

3
Chapter 3
Quick Start
Your Wasp CCD Scanner is ready to go.The default settings of the Wasp
CCD Scanner have been pre-programmed for the most common bar code
configurations.Use the "CCD Setup & Configuration" sections only to
customize the Wasp CCD settings. Please review the 'Enable Bar Code
Symbologies' configuration on pages 11 and 12 to see the list of bar code
symbologies which are enabled by default.
Tip: Use the pre-printed "Bar Code Test Symbols" in Appendix A on page 20
as a test chart to begin practicing scanning.

4
Chapter 4
Bar Code Symbologies
Bar codes are symbols consisting of a series of bars and spaces which can be
applied to packages, cartons, bottles, and other commercial products. The bars
and spaces in each symbol are grouped in such a way to represent a specific
ASCII character or function. The interpretation of these groups is based on a
particular set of rules called symbologies. Various symbologies have been
developed for particular applications. Some examples are shipping and
receiving, manufacturing, retail, healthcare, transportation, document
processing, tracking, and libraries.
The resolution of a bar code is dependent on the narrowest element of a bar
code (X dimension), and can vary from high density (nominally less than 0.009
in./0.23 mm), medium density (between 0.009 in./0.23 mm and 0.020 in./0.50
mm), and low density (greater than 0.020 in./0.50 mm). Medium and low
densities are the most common since these are the easiest to read (scan) with
nearly all scanning devices. The Wasp CCD scanner can read bar codes with
X-dimensions as low as 5 mils (0.005 in./0.127 mm).
The Wasp CCD scanner can read the most popular bar code symbologies
including Code 39, Code 128, Interleaved 2 of 5, UPC-A, UPC-E,
EAN/JAN-8, EAN/JAN-13, Codabar, MSI Plessey, and Code 93.
Please see test chart on page 20.

5
Chapter 5
CCD Setup & Configuration
In order to configure the Wasp CCD scanner, you must familiarize yourself with
the setup procedures on the following pages.The default settings of the Wasp
CCD scanner are identified on each page and clearly marked with an asterisk
(*). The default settings have been preprogrammed for the most common
bar code configurations. Use the CCD Setup & Configuration only to
customize the Wasp CCD settings. If you need to configure the Wasp CCD
reader, the default settings will be overwritten. All the programmed settings are
stored permanently in non-volatile memory.Therefore, your configuration will be
maintained even if keyboard power to the Wasp CCD scanner is removed by
turning off your PC.
In order to configure the Wasp CCD, three basic steps need to be followed for
each programmed setting:
(1) Scan the 'Begin' bar code with the Wasp CCD reader to select
your configuration
(2) Scan the appropriate setting(s) to customize the CCD configuration
(3) Scan the corresponding 'End' bar code with the Wasp CCD reader
Note: If you are unsure whether or not you have programmed the scanner
properly, return to page 6 and return the scanner back to the default settings.
Then begin the configuration process again.

6
The 'Set Default' configuration restores the factory default settings.
Tip: Use this option to restore the factory default settings if you are
unsure of your CCD’s configuration. The 'Set Default' configuration is
very useful when you need to reprogram yourWasp CCD reader after the
defaults have been changed. By setting the default configuration, the user
knows precisely the configuration for each programmed setting.
CCD Setup & Configuration
—Set Default Configuration
Default
Begin
End

7
Note: Please use Appendix B regarding the prefix string.You may add up to 4
characters as a Preamble.
Note: Please refer to Appendix B regarding the suffix string.You may add up to
4 characters as a Postamble.
Preamble
Postamble
EndSet
The 'Preamble/Postamble' configuration is used to add a prefix or suffix set of
characters to the bar code value. Up to 4 characters may be added for each
option separately.Preamble and postamble characters can function concurrently,
but need to be configured separately.
To add preamble or postamble characters, follow the steps below:
(1) Scan the 'Begin' bar code on this page
(2) Scan the 'Preamble' or 'Postamble' option
(3) Use Appendix B on page 23 to locate the characters you want to add as
preamble or postamble characters. Find the two character 'Code' associated
with the character you want to add. Scan the two characters on page 25.
Make sure that you scan the two bar codes associated with each letter before
preceding to the next character. This step can be repeated up to six more
times - seven total. For example, to add the letter "A," scan the "4," and then
the "1" on page 25.The letter "A" will always appear in your data as a prefix
or suffix to the bar code value.
(4) Scan the 'Set' option at the bottom of this page.
(5) Scan the 'End' bar code on this page.
CCD Setup & Configuration
—Preamble/Postamble Configuration
Begin